Skip to content
Website
🧱 CFC 283Glued, floating or nailed installationChapter 9 of 10 in the section

On heating: full-surface bonding recommended, thermal resistance of the assembly and protocol

This chapter covers the mastery of parquet installation on heated screeds. You will learn how to calculate the overall thermal resistance of the floor assembly, rule out insulating air gaps typical of floating installations, and verify the compliance of the heating-up protocol before starting the full-surface bonding of your parquet elements.

Key takeaways

  • Full-surface bonding ensures direct heat transfer without an insulating air cushion.
  • The total thermal resistance of the covering and its adhesive must not exceed the permitted limit.
  • The heating-up protocol must be signed by the heating engineer before any installation work begins.
  • The substrate surface temperature must imperatively stabilize between eighteen and twenty-two degrees during bonding.

Full-surface bonding eliminates the insulating air cushion of floating systems

On a low-temperature underfloor heating system, the thermal conductivity of the system depends on intimate contact between the mineral substrate and the wood overlay. In a floating configuration, the resilient underlay and the thin trapped air gap beneath the boards form an unintended thermal break. Stagnant air has a very low conductivity, in the order of 0.026 W/(m·K), which slows down the upward heat flux and forces the heating installation to raise its flow temperature to compensate for this barrier. This overheating increases the differential expansion of the wood and raises the building's energy consumption.

Transmission bridge via full-surface bonding
Continuous bond achieved by the regular squashing of polymer or polyurethane adhesive beads using a suitable notched trowel, eliminating any air voids between the mineral screed and the underside of the parquet boards.

Full-surface bonding meets this physical requirement precisely. By ensuring direct and full contact over the entire surface, the cured adhesive film contributes to heat diffusion through pure conduction. SIA 253 governs these bonded floor coverings and emphasizes the importance of flawless adhesion to guarantee the performance of the floor-integrated emitters. In addition, the adhesive bonds the wood to the mass of the screed, reducing transversal dimensional deformations induced by seasonal thermal cycles.

Thermal and mechanical behavior according to the installation method on underfloor heating
Evaluation criterionFull-surface bondingFloating installation with underlay
Added thermal resistanceLow: continuous bond without air voidsHigh: insulating underlay and air cushion
Heating efficiencyOptimal, homogeneous temperature riseDegraded, energy losses and overconsumption
Dimensional stabilityExcellent, restrained by the adhesive filmAverage, increased risk of board cupping
Acoustic comfort against footstep noiseMuted and muffled, no box resonanceHollow sound requiring heavy treatment

Verification of the thermal resistance of the assembly and control of the heating-up protocol

For floor coverings installed on heated screeds, the total thermal resistance of the floor assembly must not exceed 0.15 m²·K/W in order to maintain the efficiency of the thermal system and the durability of the overlay.

Norme SIA 253

The calculation of total thermal resistance takes into account the thickness of the parquet divided by its nominal thermal conductivity, plus the specific thermal resistance of the adhesive bed. Solid or engineered oak displays an average conductivity of 0.13 to 0.15 W/(m·K). To comply with the strict ceiling of 0.15 m²·K/W set by professional rules and standard SIA 253, the total thickness of the parquet element generally does not exceed fourteen to fifteen millimetres. Dense and stable woods, such as oak, are preferred over reactive species like beech or maple.

  1. 1. Receive and check the heating-up protocolThe document drawn up jointly by the heating engineer and the screed layer attests to the gradual temperature rise and then the holding plateau. Installation is formally suspended until this report is initialled by the site management.
  2. 2. Verify the lowering of the screed temperatureThe heating system must be turned off or modulated at least forty-eight hours before bonding. At the time of installation, the screed surface must display a stable temperature between eighteen and twenty degrees.
  3. 3. Check the ambient climate in the roomThe relative humidity of the air must imperatively be between forty and sixty percent, with an ambient temperature of at least eighteen degrees to ensure optimal cross-linking of the adhesive.
  4. 4. Gradually reactivate the system after curingAfter the complete polymerization time prescribed by the adhesive manufacturer, restarting the heating is done in increments not exceeding two to three degrees per day until the nominal operating regime is reached.

Receipt of the heating protocol and preliminary interface checks

Before starting any installation operations, the parquet layer must request the official screed heating-up protocol, completed and signed by the companies responsible for the heating and the screed. This document certifies that the complete cycle of temperature rise, maximum plateau, and controlled cooling has been fully executed. For the parquet layer, this protocol constitutes an essential contractual document: it guarantees the release of the initial shrinkage tensions of the mortar and the initiation of the evacuation of residual water. The absence of this written document prohibits the opening of the flooring construction site, as installing on a heated substrate that has not been cycled exposes the work to screed cracking or massive deformations of the boards due to subsequent thermal shocks.

Measuring the residual moisture of the screed constitutes a major technical hold point. Even after a complete heating cycle, the parquet layer carries out their own cross-check using the calcium carbide meter, the only destructive method recognized to reliably determine the actual moisture state of the binder at the core of the section. On a calcium sulfate screed on underfloor heating, the water content must not exceed 0.3 percent CM. On a cement-based screed on underfloor heating, the maximum tolerated value is 1.5 percent CM. Any exceedance requires a halt to operations and a concerted resumption of the drying heat by the heating engineer, notified in writing to the client.

Thermal resistance of the assembly and mastery of full-surface bonding

The performance of underfloor heating depends directly on the heat flux transferred to the room. In order to prevent the covering from acting as an insulating screen and forcing the heat generator to run at excessive speeds incompatible with the wood's stability, the total thermal resistance of the finished assembly (including floor covering and adhesive bed) must under no circumstances exceed the strict threshold of 0.15 square meter kelvin per watt. A parquet installed floating, with its resilient interlayer and trapped air gap, frequently exceeds this critical threshold and severely degrades thermal efficiency. Conversely, full-surface bonding ensures physical continuity without gaseous discontinuity between the upper face of the screed and the underside of the boards, allowing direct heat transmission through pure conduction.

Indicative thermal resistances according to the type of parquet and installation method
Type of parquetTotal thicknessInstallation methodThermal resistance RThermal behavior
Solid oak mosaic8 mmFull-surface bonded0.04 to 0.05 m²·K/WRapid transmission and minimal resistance
2-ply engineered oak10 mmFull-surface bonded0.07 to 0.08 m²·K/WExcellent transmission and high stability
3-ply engineered oak14 mmFull-surface bonded0.10 to 0.12 m²·K/WCompliant with maximum permissible threshold
Engineered on underlay14 + 2 mmFloating clicked installation0.16 to 0.20 m²·K/WNon-compliant, penalizing air cushion
Wide-plank solid oak20 mmFull-surface bonded0.14 to 0.16 m²·K/WHigh inertia and risk of shrinkage effects

The choice of adhesive and notched trowel conditions thermal efficiency and mechanical hold. Solvent-free reactive adhesives, notably silane polymers or hard-elastic single-component polyurethanes, are required for their resistance to shear stresses and thermal aging. Application is carried out using a B11 or B15 notched trowel, ensuring a covering transfer of at least 80 percent of the underside of the boards. Careful flattening of the ridges during beating is decisive: any inclusion of residual air creates an inverse thermal bridge, slowing down heat diffusion and causing local overheating beneath the wood.

The reactivation of the heating takes place after complete curing of the adhesive, generally after seven days of stabilization. This temperature rise is carried out gradually, in steps of 2 to 3 degrees Celsius per twenty-four hours, until the usual setpoint is reached. Throughout the building's operation, the contact temperature at the surface of the parquet must never exceed 27 degrees Celsius, under penalty of causing abrupt hygrometric shrinkage, longitudinal cracks, or detachment of the wood.

Management of non-conformities, missing protocol, and thermal damage

On underfloor heating, interface failure between the substrate and the wood generates heavy disputes. As soon as a discrepancy occurs during preparation or after commissioning, the parquet layer applies a rigorous traceability procedure to clear themselves of technical liability.

  1. Observation of overheating or thermal blockageIf calculations reveal a thermal resistance of the floor assembly higher than the permissible limit prescribed by standard SIA 253, or if the surface temperature exceeds the maximum operating value, the notice of anomaly is notified before any bonding begins.
  2. Diagnosis of parquet detachmentIn the event of hollow sounds or element detachment after heating, carry out spot checks. The analysis determines whether the failure stems from the reactive adhesive, insufficient surface cohesion of the screed, or a residual air cushion detrimental to bonded installation and heat transmission.
  3. Conservatory measures and remediationRecord ambient humidity and flow temperature. Stop the installation if cracks appear. Remediation requires the total elimination of adhesive residues, surfacing of the mineral, and a complete revaluation of the conductivity of the receiving assembly.

Frequently asked questions

What should be done if the site management demands installation without a heating protocol?

The parquet layer formally refuses to intervene via a substantiated written notice in accordance with standard SIA 118. The absence of thermal conditioning prevents the dimensional stabilization of the screed and the expulsion of residual moisture. Installing parquet without this signed document transfers full responsibility for future defects, such as cupping or cracking, onto the flooring installation company.

How to react if the thermal resistance of the parquet exceeds the prescribed threshold?

When the calculated thermal resistance of the floor assembly exceeds the limit value of standard SIA 253, the parquet layer refuses the planned material in writing. A covering that is too insulating blocks heat diffusion, induces overheating at the adhesive bed, and impairs the performance of the installation. A denser species or a suitable reduced thickness should be proposed.

Why is bonded installation required in the case of reversible underfloor heating?

Bonded installation ensures optimal thermal continuity without an insulating air cushion between the substrate and the wood element. In cooling mode, continuous contact prevents points of interstitial condensation beneath the boards. A floating installation would create a captive air gap detrimental to thermal efficiency, risking major dimensional variations and board warping during cycle reversals.

What ambient temperature must be maintained during bonding work?

The heating must be turned off or lowered to maintain a screed surface temperature of between 15 and 18 degrees Celsius during adhesive application and complete curing. The room atmosphere must display a relative humidity in accordance with the requirements of standard SIA 253. Gradual reheating only takes place after complete drying of the adhesive.

Texts and standards cited

  • norme SIA 118General conditions for the execution of construction work and management of interruption notices
  • norme SIA 253Bonded floor coverings: adhesion requirements, residual moisture, and permissible thermal resistance

In the same section