Skip to content
Website
🧱 CFC 283Section 3 of 610 chapters

Glued, floating or nailed installation: the execution reference standard

This section is aimed at parquet layers, site foremen and construction managers who must specify or execute the implementation of wooden flooring on various substrates. According to SIA 253 standard, each installation method imposes strict rules regarding bonding, elasticity and decoupling. Mastering these techniques guarantees the mechanical durability of the work, acoustic comfort and the natural breathability of the wood.

  • 10chapters
  • 22 000words
  • 6sections in the training course
  • 60chapters in total

Key values to remember 5

norme SIA 253

10 to 15 mm

Minimum width of the continuous perimeter gap along walls

norme SIA 253

400 mm

Maximum centre-to-centre spacing between battens for nailed solid boards

norme SIA 253

0.15 m²K/W

Maximum permissible thermal resistance for the parquet and underlay assembly on underfloor heating

norme SIA 253

300 mm

Minimum longitudinal offset between end joints of two successive rows

norme SIA 253

8 to 10 m

Maximum linear dimension of a room without an expansion joint in floating installation

Scope of the section and limits of services

The installation of wooden floor coverings comprises three fundamental methods: direct adhesion to the screed using reactive adhesive, decoupled assembly on a resilient underlay known as floating, and mechanical fixing on battens or subfloors. The SIA 253 standard governs these operations by specifying flatness tolerances, ambient conditions and the management of dimensional deformations of wood caused by variations in hygrometry.

This technical silo deals exclusively with the craft of the parquet layer (CFC 283). Excluded from the scope of intervention are:

  • The pouring of cement or calcium sulphate screeds, drying times and moisture measurement using the calcium carbide method (CFC 281).
  • The supply and installation of skirting boards, threshold profiles, plinths and perimeter joinery cladding (CFC 273).
  • The sizing, installation of heating pipes and adjustment of the heating curve for underfloor heating (CFC 241).
  • Waterproof joints and waterproofing screeds under tiling or natural stone (CFC 282).

The intervention begins with the controlled unpacking of parquet bundles previously acclimatised in heated spaces, and extends until the delivery of a flat, stable floor that is ready to receive its impregnation or varnishing treatments.

Execution method and reading path

To design and execute a parquet floor without the risk of cupping, uneven joints or debonding, the technical order of consultation follows the chronology of workshop and construction site decisions.

  1. Choice of mechanical and adhesive systemThe first chapter [U3-01] compares glued, floating and nailed installation according to use requirements, impact sound insulation and the presence of underfloor heating. Chapter [U3-02] covers the choice of resins (modified silane or polyurethane), trowel notch sizes and the modulus of elasticity required to control the thrust of solid boards. Chapter [U3-03] details the acoustic wedging of battens, centre-to-centre spacing and secret face-nailing to prevent any squeaking.
  2. Dimensional management and geometryChapter [U3-04] establishes the absolute rule for continuous perimeter gaps at the base of partition walls, doorframes and pipe penetrations. Chapter [U3-05] defines the critical linear measurement thresholds requiring an invisible movement joint under doorways or over long spans. Chapters [U3-06] and [U3-07] cover spatial distribution: orientation relative to grazing light, minimum offset of board ends, and rigorous chalk-line layout for complex patterns such as herringbone or chevron.
  3. Appearance, thermal constraints and corrective interventionsChapter [U3-08] organises the visual mixing of boards according to appearance classes and wood characteristics. Chapter [U3-09] brings together thermal admissibility criteria for low-temperature underfloor heating. Finally, chapter [U3-10] sets out the protocol for the surgical extraction of a damaged board in the middle of a glued field without destroying the neighbouring assembly.

📘 Chapters in this section 10

Glued, floating or nailed installation

Glued, floating or nailed: substrate, acoustics, underfloor heating and foot feel

Determine the assembly system according to the substrate, acoustic constraints and required walking comfort.

Glued, floating or nailed installation

Adhesive: elasticity, consumption, trowel and solid wood requiring greater flexibility

Master trowel notch sizes and polymer reactivity to guarantee lasting elastic support.

Glued, floating or nailed installation

On joists: centre-to-centre spacing, subfloor ventilation, skewed nailing and squeaking

Install on ventilated battens with slanted fixings to eliminate any squeaking under repeated flexing.

Glued, floating or nailed installation

Clearance everywhere: walls, pipes, door frames, and the single blocking point that causes failure

Provide the continuous perimeter clearances essential for absorbing free hygrometric swelling without buckling.

Glued, floating or nailed installation

Large area: maximum joint-free length, separating profile and corridor

Judiciously divide spacious rooms and hallways to prevent lifting caused by thermal expansion.

Glued, floating or nailed installation

Direction and offset: light, length, minimum end-joint offset and pattern

Align the axis of the boards with the source of natural light while ensuring structural offset.

Glued, floating or nailed installation

The patterns: herringbone, chevron, starting axis and actual waste

Methodically set out reference axes to lay out herringbone and chevron patterns without drift.

Glued, floating or nailed installation

Sorting boards: selection grade, knots, sapwood, and the sample setting expectations

Distribute knots and sapwood variations as soon as bundles are opened according to the client's validated expectations.

Glued, floating or nailed installation

On heating: full-surface bonding recommended, thermal resistance of the assembly and protocol

Validate the performance of low-temperature underfloor heating by checking the overall permissible thermal resistance.

Glued, floating or nailed installation

Replacing a plank: removal without damage, colour matching and reserve planks

Extract a damaged board in the middle of the floor without damaging the adjacent intact tongue and groove joints.