Skip to content
Website
🧱 CFC 283Substrate, preparation and underlaysChapter 6 of 10 in the section

Wet rooms: what is possible, what is not, and the waiver to be signed

Installing parquet flooring in a wet room is a recurring technical challenge for the flooring installer. You will learn how to identify suitable timber species and refuse floating installations, which are incompatible with ambient humidity. You will master the execution of watertight perimeter seals as well as the drafting of a formal notification and a liability waiver required by the Code of Obligations before work begins on the construction site.

Key takeaways

  • Full-surface bonding without hollow joints is strictly mandatory to eliminate any risk of moisture infiltration.
  • Dense exotic timber species such as teak or doussie guarantee optimal dimensional stability.
  • Penetrating oiled finishes prevent surface blistering caused by standing water underneath varnishes.
  • A written waiver signed by the client protects the craftsperson against risks related to usage.

Choice of timber species, full-surface bonding, and finish control in wet rooms

SIA 253 strictly regulates the installation of wooden floor coverings and points out that humid environments subject floorboards to severe dimensional variations. In a residential bathroom, the relative air humidity frequently fluctuates between 35% during the heating season and over 80% after a prolonged shower. Wood, being a hygroscopic material by nature, absorbs this water vapour and swells, then shrinks during the ventilation phase. To limit these tangential and radial stresses that cause cupping or delamination, the use of solid or engineered parquet of narrow width remains subject to choosing a timber species featuring a minimal volumetric shrinkage coefficient and excellent natural resistance to wood-destroying fungi.

Behaviour of main timber species when exposed to wet room stresses
Timber speciesDimensional stabilityWater sensitivityTechnical assessment
Teak (Tectona grandis)Very high (minimal shrinkage)Nil to very low (natural oleoresins)Approved for bonded installation
Doussie (Afzelia)High (low variation)Low (hard and dense wood)Approved for bonded installation
Iroko (Milicia excelsa)Medium to highLow after stabilisationApproved subject to ventilation
Beech or MapleVery low (high shrinkage)Very high (staining, rapid cupping)Strictly prohibited

Floating installation is strictly forbidden in damp environments by SIA 253. A non-adhering board creates an underlying air gap conducive to trapping condensation, leading to hidden mould and degradation of the underlay. The flooring installer therefore applies direct full-surface bonding onto the dry and prepared mineral screed using a silane-terminated polymer adhesive or a two-component reactive polyurethane. These adhesives maintain permanent elasticity, which compensates for shear stresses without breaking the mechanical bond. Regarding surface protection, applying a penetrating, polymerisable, and water-repellent natural oil is clearly preferable to a film-forming surface sealer. Indeed, a varnish risks flaking if water infiltrates through a micro-defect or along the edges, trapping the liquid under the watertight film and irreversibly darkening the wood fibres.

Edge waterproofing, critical zones, and formal written waiver

Water must under no circumstances be allowed to bypass the parquet flooring and infiltrate beneath the screed or against the masonry walls. The flooring installer treats the perimeter of the room with the same technical rigor as a waterproofing specialist. The perimeter edges, left with a ten to twelve millimetre gap to allow free movement of the wood, cannot remain open or be simply masked by a nailed skirting board. It is essential to install a closed-cell polyethylene foam backing cord, compressed at the core, and then extrude a high-performance elastomeric caulking sealant. This elastic perimeter joint ensures splash-proofing while absorbing the seasonal swelling of the boards without overflowing or failing under pressure. Door frame feet and radiator pipe penetrations must undergo the same systematic treatment using elastomeric sealant.

A strict geometric distinction is also required in the installation layout. Wooden parquet flooring does not constitute waterproofing tanking in the sense of SIA 253: it can never be installed directly within the footprint of a walk-in shower without a shower tray or on a surface subject to permanent standing water. The direct splashing zone around the bath and washbasins requires prompt wiping of puddles after each use, as well as a mechanical ventilation system in perfect working order capable of evacuating the vapour in under twenty minutes.

Facing these usage constraints, which the craftsperson cannot control on a daily basis, the duty to inform and the duty to notify an interruption defined by the Code of Obligations takes on its full significance. Even when the client contractually demands parquet flooring in a bathroom, the flooring installer must send them a written and documented warning prior to ordering any materials. This document explains the natural behavior of wood under the effect of water, the inherent risks of cracking, colour variation, and swelling, as well as strict maintenance rules.

Perimeter interface, elastomeric caulking, and climatic requirements of SIA 253

In wet rooms, hygrothermal behavior imposes severe constraints on the flooring installer. SIA 253 specifies requirements relating to bonded floor coverings and points out that wood constantly reacts to differences in ambient relative air humidity. Unlike dry rooms where dimensional movements remain moderate, a bathroom undergoes sudden cycles of saturated vapour followed by drying phases via mechanical ventilation. A full-surface bonded installation with a single-component polyurethane or silane-terminated polymer adhesive is essential to curb cupping. Floorboards must demonstrate proven compatibility with these loads, excluding floating or click systems that promote pockets of condensation beneath the facing.

Technical treatment of perimeter junctions and singularities in wet rooms
Interface zoneHydraulic stressWaterproofing deviceSealing mastic
Perimeter of sanitary fittings (bath, tray)Direct runoff and frequent splashingRound cellular closed-cell backing cord compressed to 30%MS polymer elastomeric sealant with fungicide
Perimeter edges against partitionsWater vapour and cyclical ambient humidityCalibrated perimeter expansion gap between 8 and 10 mmShrink-free elastic polyurethane sealant
Penetrating pipework openingsPoint condensation and localised thermal bridgeRaised waterproof sleeve and compressible ringContinuous bead of water-repellent silane polymer
Door threshold and tiling transitionWater cleaning and accidental stagnationBonded transition profile with capillary breakFlexible waterproof joint with elastic recovery

The execution of edge joints determines the durability of the work. Under no circumstances must the flooring installer block the edges with mortar or rigid mastic. The closed-cell polyethylene foam backing cord is inserted into the perimeter space to prevent the mastic from adhering on three faces, thereby ensuring purely two-sided working of the elastomer. After degreasing the board edges and applying a suitable primer if the chosen timber species is particularly dense or resinous, the sealant bead is smoothed with a spatula using a neutral agent. This continuous barrier prevents lateral infiltrations of soapy water beneath the parquet while allowing the shrinkage and swelling movements required by trade standards.

Written information, waiver clause, and operating protocol

Faced with a client's express desire to install parquet flooring in a damp room, the flooring installer has an obligation to formalise a detailed technical warning. According to the Code of Obligations, the contractor incurs liability for any defects resulting from the work if they have not notified the client of the risks of alteration linked to the physical characteristics of wood. This warning cannot remain verbal: it must be the subject of a specific contractual document drawn up before placing the order or opening the construction site. The waiver does not exempt the installer from correctly executing perimeter joints or complying with SIA 253 tolerances, but it transfers the direct consequences of the material's natural behavior when exposed to water onto the client.

  1. Prior technical notification and risk inventoryDraft a technical memo describing the physical limits of solid or engineered parquet flooring in damp environments, specifying the risks of joint darkening and board cupping.
  2. Signing of the liability waiver agreementHave the waiver addendum co-signed by the client and the architect before any timber is delivered to the construction site, integrating a reminder of the SIA 253 requirements.
  3. Delivery protocol and handover of maintenance instructionsCarry out a joint inspection after the final finishing coat has been applied, with hand-delivery of a nourishing vegetable soap and a suitable maintenance oil.

Surface treatment completes the installation. In wet rooms, varnished or sealed finishes are strictly prohibited: the slightest micro-crack along a joint allows water to infiltrate by capillarity, trapping moisture under the film and causing irreversible darkening of the wood through tannin reaction. Only natural siccative oils, applied to saturation in successive passes until mechanical refusal, offer a breathable and water-repellent protection. This treatment allows water to bead on the surface while letting the wood release absorbed vapour. Finally, the flooring installer records in their delivery report the operator's obligation to wipe up any standing water without delay after using water points and to ban rubber bath mats that trap condensation.

Claim management in damp environments and repair protocol

When defects occur on bathroom parquet flooring, the manifestations are almost systematic: pronounced cupping of the boards, wood darkening at the ends or near sanitary fittings, cracking of the perimeter joint, and localised detachment of the adhesive bed. Facing these damages, the flooring installer's reaction must follow a methodical technical and contractual approach to determine the exact origin of the claim and assert the technical reservations notified prior to installation.

  1. Hygrometric reading and initial diagnosisMeasure the residual moisture content of the wood using a capacitive and pin-type moisture meter, then check the room's ambient climate with a thermo-hygrometer. Determine whether the damage originates from un-wiped standing water, faulty ventilation, or underlying infiltration caused by a ruptured flexible waterproof joint.
  2. Comparison with the signed waiverReview the information protocol and the written waiver validated by the client prior to the work. Examine whether operating rules were breached, notably through prolonged lack of ventilation, placing wet laundry on the floor, or using stripping cleaning products that destroyed the oil treatment.
  3. Conservatory measures and controlled dryingImmediately remove perimeter finishing profiles to release the expansion gap blocked by transverse swelling of the wood. Install an air dehumidifier without direct hot air blowing, so as to slowly re-balance the material without inducing internal stresses that cause cracking.
  4. Decision to repair or removeOnce moisture has stabilized, test the adhesion of the system to the substrate. If the polymer adhesive bed has ruptured due to shear stress or if the wood shows internal rot, localized removal is required. If adhesion remains, corrective sanding and full impregnation with natural oil can be carried out.

When degradation results from proven non-compliance with maintenance instructions listed in the formal notice, the written waiver protects the craftsperson against abusive claims in accordance with the provisions of the Code of Obligations. SIA 253 points out that parquet floors are not waterproof by nature. If the client confirmed the implementation by explicitly accepting these constraints, the repair costs remain their sole responsibility.

Frequently asked questions

Can engineered parquet flooring be installed in a wet room?

Engineered parquet flooring is strongly discouraged in bathrooms. Even though its cross-layered backing limits overall dimensional variations, moisture penetrating the edges causes delamination of the wear layer and irreversible swelling of the core. Only solid parquet flooring of a naturally stable and rot-proof timber species, fully bonded and saturated with oil, offers the required resistance against occasional water exposure.

How to treat waterproofing under sanitary appliances?

Parquet flooring must never be extended under bathtubs or floor-level shower trays. The work systematically stops at the edge against the masonry or tiled plinth that has been waterproofed beforehand. The junction between the board and the equipment requires marine-grade elastomeric sealant caulking over a cellular backing cord, in order to compensate for the dimensional movements of the wood while guaranteeing a watertight barrier compliant with SIA 253.

Which finish should be preferred between oil and surface sealer in a bathroom?

Natural siccative oil is mandatory in wet rooms. A surface sealer forms a superficial waterproof film that eventually cracks under the hygrothermal deformations of the parquet. Water then infiltrates beneath the varnish without being able to evaporate, causing rot and darkening of the wood. Oil impregnation saturates the cellular network in depth, preserves vapour permeability, and allows easy regular touch-ups on wet areas.

Why have a written waiver signed for wooden flooring in a damp room?

Wood reacts directly to climatic variations and fears standing water. By virtue of the duty to notify arising from the Code of Obligations, the company formally informs the client of the risks of cupping, discoloration, and biological degradation. The signature of this waiver attests that the client has properly received strict drying and ventilation guidelines, and that they assume responsibility for claims related to the room's operating conditions.

Texts and standards cited

  • SIA 253Flexible floor coverings and parquet flooring: installation instructions and permissible climatic conditions

In the same section