Key takeaways
- The breaking joint at the threshold divides the parquet into independent dimensional movement zones.
- Standard SIA 253 stipulates interrupting the installation at doorways to prevent buckling.
- The peripheral clearance under the future threshold profile must be maintained on both sides.
- The thickness difference between tiles and parquet requires rigorous shimming right from installation.
Interrupting the continuity of the parquet at the door rebate
The temptation of continuous installation from a bedroom to a hallway is one of the major causes of defects in parquet flooring. Wood constantly reacts to variations in ambient air humidity, increasing in volume during the humid summer period and shrinking during the winter heating period. If a parquet floor is extended without a break through a narrow opening, the total moving mass over the cumulative length of the work is choked at the door frame passage. The tangential and radial forces that then occur cause irreversible deformations: cupping in the centre of the room, shearing of the full-surface adhesives or sudden opening of the joints at the head of the board.
Glued or floating floor coverings must be separated by appropriate movement joints at surface narrowings, notably at doorways, to guarantee the free contraction and swelling of the material without destructive mechanical stress.
Norme SIA 253
For the parquet layer, the separation joint at the threshold is not simply an aesthetic cut, but a functional element that divides the floor into mechanically autonomous bays. This rule applies imperatively to floating installations, where the overall inertia of the surface pushes the peripheral wedges beyond permissible tolerances, but it remains just as essential during glued installation on a cement or calcium sulphate screed. When the supporting screed itself features a technical crack-induction joint or expansion joint cast by the screed layer, the parquet layer is obliged to rigorously superimpose their wood joint in vertical alignment with this break.
The positioning of the cut must be calculated in coordination with the opening direction of the door leaf. The separation edge must imperatively be located exactly under the closed door panel, set back by about one-third of the door frame rebate from the interior room. In this way, the technical demarcation or the space reserved for the future joint cover remains invisible from both sides when the door is closed.
Managing movement gaps and level differences between floor coverings
The execution of the threshold regularly brings into contact two rooms with dissimilar service conditions, such as a bedroom with glued parquet and a hallway exposed to heavy traffic, or two distinct materials, such as a junction between solid oak and ceramics sealed by the tiler. The parquet layer must guarantee the maintenance of a clear expansion gap on either side of the central profile, without ever filling this reserve with rigid mortar, hard glue or a lost shim forgotten under the edge.
| Installation system | Minimum clearance reserved at the threshold | Level adjustment | Maintenance of decoupling |
|---|---|---|---|
| Floating engineered parquet | 10 to 12 mm | Inclined or rebated transition profile | Total prohibition of through-fixing in the parquet |
| Full-surface glued solid parquet | 8 to 10 mm | Direct flush finish or flat stop profile | Compressible foam joint backing before flexible sealant |
| Parquet and tile transition | 8 mm on the wood side | Alignment with finished ceramic edge | Chamfered wood board or protected against chipping |
- Checking screed level marks before startingCheck the finished height of the tiles or adjacent floor relative to the raw substrate level. In the event of an unforeseen deviation outside tolerance, notify the non-conformity before starting to glue the boards.
- Marking out the rebate axisLocate the cutting line under the future closed door panel. Transfer this axis onto the screed to position the mechanical break and align the starting rows.
- Sawing and maintaining the end clearanceCut the boards cleanly using a rail-guided plunge saw. Place temporary shims of calibrated thickness to preserve the movement space until finishing work is completed.
- Installing temporary protectionInsert a temporary joint backing or heavy-duty adhesive tape to prevent sanding slurry, dust or excess oil from clogging the expansion reserve.
- Transition profile
- Metal or wood element mechanically fixed to the supporting floor without making the coverings integral, overlapping the two edges to mask the expansion gap while tolerating a thickness differential.
When the connection is made with a level difference, standard SIA 253 requires limiting any abrupt step likely to create a tripping hazard. The parquet layer ensures that their final board has a clean, perfectly straight cut, free from splinters. If a deviation of a few millimetres persists with the adjacent floor covering, the future installation of the threshold profile by the joiner must freely cover the edge of the parquet, without any screws passing through the wear layer or glue spots blocking the wood edges.
Parquet fractioning at the threshold and maintaining peripheral clearance
The visual continuity of a parquet floor between two adjoining rooms exposes the work to destructive cumulative mechanical thrusts. Two neighbouring rooms have distinct indoor climates in terms of relative humidity, sunlight and exposure to thermal losses. Laying boards in a single piece across a doorway amounts to adding the dimensional variations of the two surfaces over a single free span. When the wood swells in summer, the expansion force compresses the rows in the narrowing of the passage, causing lifting in the centre of the rooms or warping of the boards at the frame.
For the parquet layer, the physical separation of the flooring at the doorway constitutes a primary technical obligation in accordance with standard SIA 253. This separation must align rigorously with the plane of the closed door, so that the interruption disappears visually under the leaf. The separation joint at the threshold must absorb the transverse and longitudinal movement of the two bays without creating a rigid bridge. Each installation area thus becomes an independent structure, free to slide on its substrate under seasonal variations.
The positioning of the cut must take into account the installed or future joinery. In glued installation, the parquet layer stops the gluing cleanly in line with the cutting line to prevent adhesive mortar from spreading under the expansion void. In floating installation, the resilient strip or flexible caulking must be kept clean of any sawing debris. The tongues and grooves at the end of the bay must never cross the separation line; they are sawn clean flush to ensure that the two parquet sections retain their geometric autonomy.
Edge connection and compensation for level differences
When the parquet meets an adjacent floor covering of a different nature, such as natural stone, tiles or resin, a level difference between coverings frequently appears due to variations in material thicknesses or structural work execution tolerances. The parquet layer's work focuses on the geometric adaptation of their own assembly: adjusting the underlay thickness in floating installation, choosing a species of compatible thickness or carefully shaping the head edge.
| Altimetric configuration | Observed level difference | Parquet layer's execution | Interface precautions |
|---|---|---|---|
| Direct level flushness | Less than 1 mm | Clean square cut, discreet edge chamfer, localised flush sanding | Guarantee maintained clearance on both sides without adhesion to the neighbouring material |
| Parquet lower than adjacent floor | 2 to 5 mm | Clean set-back stop, calibrated sanding of the edge before staining or finishing | Check clearance under the future metal threshold installed by the joiner |
| Parquet higher than adjacent floor | 2 to 8 mm | Edge softening by light chamfer or matching rebate on the face | Preserve the free zone under the rebate for free expansion of the board |
| Higher level difference | More than 8 mm | Installation of a reinforced edge board serving as a clear square stop heel | Coordination with site management for setting a suitable transition profile |
- Taking level marks and checking clearanceMeasure the level difference with a precision straightedge under the door rebate relative to the finished or planned contiguous floor. Mark the separation line on the exact axis of the closed door panel.
- Edge cutting and deburringExecute the final cut of the boards using a rail-guided plunge saw to obtain a perfect straight edge, maintaining the required expansion space without mitre contact.
- Edge protection treatmentApply a primer, saturating oil or impregnating varnish to the cut raw edges to prevent any local moisture absorption during construction site cleaning.
- Preservation of the matching rebateClean the transition space with an industrial vacuum cleaner and check for the total absence of hard bodies or adhesive residues before the installation of the finishing profile by the joiner.
The careful treatment of the cut edge determines the durability of the work at the threshold. The upper edge must receive a light deburring with fine-grain sandpaper to eliminate micro wood splinters likely to be torn off by the repeated passage of users. During the subsequent general sanding and finishing application steps, the parquet layer must ensure that they do not fill the separation void with abrasive dust agglomerated by the finishing products, which would ruin the mechanical efficiency of the device.
Threshold defects: diagnosis of faults and remedial work for bound parquet floors
The absence of a separation joint at a doorway is one of the most frequent defects in parquet flooring. When the parquet is laid in one piece between two rooms, the work undergoes seasonal hygroscopic variations over a disproportionate cumulative dimension. As soon as the relative humidity of the air rises in summer, the wood swells across the grain. Blocked in the door opening by the joints or frame feet, the parquet cannot slide: it rises in a ridge in the middle of the passage, squeaks underfoot, or cracks the adjacent boards under mechanical pressure.
- Locating the screed joint and marking out under the rebateLocate the exact alignment of the door leaf to position the cut in the door's covering axis, in direct superposition with the breaking joint of the underlying screed.
- Interruption sawing with a plunge sawPerform a clean cut with a circular plunge saw on a guide rail equipped with a micrometric depth stop, ensuring the wood thickness is sliced cleanly without cutting into the substrate or damaging any heating pipes.
- Clearing the gap and purging the cutting lineHollow out the material with a chisel along the door frames to release a clear clearance of at least 8 to 10 millimetres on either side of the edge, then carefully vacuum all sawdust that would block expansion.
- Edge treatment and junction protectionIn the event of an altimetry offset with the adjacent room, rectify the sawn edges before installing a suitable transition profile that masks the cut while guaranteeing free bilateral sliding.
When findings reveal an unforeseen level difference between two contiguous floor coverings, the parquet layer must under no circumstances compensate for the height difference with an excess of adhesive under the parquet. Shimming or underlying shape correction falls under screed preparation work. The parquet layer adjusts their edge flush with precision to deliver a clean, straight edge, in accordance with recognised rules of engineering.
Frequently asked questions
How to repair a glued parquet floor that has lifted under a door in summer?
The parquet must be sawn along the closing axis of the door leaf using a rail plunge saw set to the exact thickness of the wood. A clear gap of 10 millimetres is then cleared out with a chisel. As soon as the lateral mechanical stress is released, the boards drop back onto their adhesive bed. A repair resin is injected if the initial bonding failed under the pressure.
Can a floating parquet floor be installed continuously from a hallway into several bedrooms?
This installation method is strongly discouraged and contrary to Swiss professional rules. Each room has its own microclimate and service loads. The accumulated global mass generates a friction force that exceeds the floor's free elongation capacity. Installing a separation joint at each room's threshold is required in order to fraction movements and avoid deformations at partition walls.
What should be done if the screed has an 8 mm level difference between the hallway and the wet room?
The parquet layer must not make up for such unflushness with a thick bed of adhesive. This anomaly exceeds the execution tolerances permitted by standard SIA 253. The situation must be reported to the site manager so that the screed layer can produce a compliant compensation ramp. The parquet layer's role then consists of laying their boards level and providing the necessary clearance at the threshold.
Which transition profile should be favoured during a transition between parquet and tiles?
The choice depends on the finished level of both materials. If both floor coverings arrive at rigorously the same edge, a compressible cork joint or an aluminium or brass T-profile screwed or clipped into the substrate is perfectly suitable. In the event of an altimetry offset, a bevelled level-adjusting transition profile makes it possible to erase the step without hindering peripheral clearance.
Texts and standards cited
- norme SIA 253Wooden floor coverings (parquet) and textile or resilient floor coverings: substrate requirements, flatness tolerances and movement joint fractioning rules.
