Skip to content
Website
🧱 CFC 283Moisture in timber and in the roomChapter 7 of 10 in the section

On underfloor heating: stable timber species, limited thickness and surface temperature

This chapter enables you to select and validate timber species permitted on underfloor heating. You will learn how to calculate the thermal resistance of the assembly, verify compliance with the surface temperature thresholds prescribed by standard SIA 253, and technically reject reactive timber species that are incompatible with the constraints of underfloor heating.

Key takeaways

  • The choice of timber species on underfloor heating directly depends on its volumetric shrinkage coefficient.
  • Oak and stable dense woods remain the technical benchmark for limiting defects.
  • The maximum thermal resistance of glued parquet must not exceed the usual normative threshold.
  • The surface temperature of the parquet in service must never exceed the safety limit.

Shrinkage behavior and reactivity: classifying woods according to their dimensional stability

Direct heat transfer from the backing continuously modifies the equilibrium moisture content of the installed wood. During the winter period, the parquet experiences a constant thermal gradient: the underside in contact with the heated screed reaches a higher temperature than the visible surface exposed to the ambient air. This differential intensively dries out the woody material, which frequently drops below 6% internal moisture in the dead of the heating season. Consequently, the appearance criterion must necessarily take a back seat to the physical properties of each timber species, in particular the tangential and radial shrinkage coefficient.

Reactivity of a timber species
The ability of a wood to change its volumetric dimensions according to variations in its moisture content. It is assessed by the ratio between radial and tangential shrinkage and the overall deformation amplitude for a 1% hygrometric variation.

Certain timber species react in a measured way to seasonal drying, while others exhibit critical instability. Beech and sycamore maple, for example, have a particularly high volumetric shrinkage coefficient. Subjected to an underlying heat source, these woods develop considerable internal stresses that inevitably cause the appearance of shrinkage cracks, pronounced unevenness and millimetric joint openings that are impossible to mask. Conversely, European oak serves as the technical reference for heated screeds, thanks to its regular cellular structure and low propensity for sudden dimensional variations.

Behavior of the main parquet timber species in response to thermal drying
Timber speciesDimensional stabilityLevel of reactivityAdmissibility opinion for underfloor heating
European oakExcellentLow to mediumFully permitted in engineered or calibrated solid wood
Doussié / TeakRemarkableVery lowPermitted subject to traceability and certified drying
Thermo-treated ashExcellentVery lowPermitted thanks to the thermal modification of the fibres
Natural ashMediumMedium to highNot recommended or restricted to small element widths
CherryLowHighNot recommended without strict hygrometric air regulation
Beech (unsteamed)Very poorVery highProhibited on heated screed due to shrinkage
Sycamore mapleMediocreHighProhibited due to proven risk of deformation and cupping

Thickness limits, thermal resistance and absolute control of surface temperature

The parquet installer does not manage the layout of the heating pipes or the operation of the boiler, but it is incumbent upon them to check that the flooring assembly does not form an excessive thermal barrier above the floor. According to standard SIA 253, the overall thermal resistance of the finished floor element, including the installation adhesive and any authorised acoustic underlays, must not exceed the usual threshold of 0.15 m²·K/W. If the timber layer presents a higher resistance, the heat remains trapped in the screed, increasing energy consumption and forcing the heating engineer to raise the water temperature, which destroys the adhesive and the wood.

This maximum resistance depends directly on the thermal conductivity of the wood, which generally lies between 0.13 and 0.17 W/(m·K) for common dense hardwoods. In workshop and construction site practice, this physical constraint imposes a strict thickness limit: the glued parquet assembly should not exceed 15 to 16 mm to maintain efficient energy transfer. Traditional solid parquet with a thickness of 22 mm slows down the heat flow and promotes destructive overheating on the underside of the plank.

The flooring and its connection to the substrate must be designed and executed in such a way as to withstand without damage the thermal and mechanical stresses resulting from the normal operation of the heating system.

Norme SIA 253
  1. Examination of the heating commissioning reportRequest and analyse the official report drawn up in accordance with the rules recognised by the preceding trades. The progressive heating and the holding phase must be formally certified before any delivery of material to the premises.
  2. Calculation of the assembly resistanceAdd up the inherent resistance of the timber species according to its certified technical data sheet, that of the specified adhesive bed and that of any acoustic insulation bed to verify strict compliance with the 0.15 m²·K/W ceiling.
  3. Checking the residual moisture of the woodMeasure the hygrometry of the parquet bundles upon delivery using a calibrated measuring pin. The moisture of the planks must imperatively be within the range of 7% to 9% to avoid any premature shrinkage as soon as it is put into service.
  4. Notification of operating instructions to the clientRemind them in writing of the thermal usage limits, in particular the prohibition against exceeding 27 °C on the parquet surface, the prohibition against covering the planks with thick carpets with an insulating backing, and the obligation to maintain the relative humidity of the air between 35% and 60% during winter.

Compatibility of timber species: technical trade-off between reactivity and stability

The hygrothermal behaviour of parquet on heated screed tolerates no compromise dictated by mere aesthetic considerations. The continuous heat diffusion exerted from underneath creates an inverted thermal gradient that accelerates the internal desiccation of the woody material, amplifying tangential and radial shrinkage phenomena. Within the technical framework set by standard SIA 253, the parquet installer accepts liability for the mechanical integrity of the joints and the strict limitation of joint openings in service. Choosing an unstable species inevitably leads to shear stresses capable of breaking the adhesion of the adhesive or splitting the wood along the grain. The evaluation of the species is therefore primarily based on its unit volumetric shrinkage coefficient, its anisotropy ratio and its reaction speed to variations in relative humidity, relegating surface hardness to second place.

Behavior of common timber species on heated screed and admissibility according to standard SIA 253
Timber speciesReactivity and stabilityAverage tangential shrinkageTechnical application advice
European oakStable to moderately stableModerate (~ 0.26% per % of moisture)Recommended without reservation in thin solid wood or engineered wood
Doussié / AfzeliaVery stableVery low (~ 0.18% per % of moisture) perfectamente adapted, minimal dimensional variations
MerbauVery stableVery low (~ 0.19% per % of moisture)Recommended, excellent stability under thermal cycling
Sycamore mapleReactiveHigh (~ 0.31% per % of moisture)Not recommended, critical risk of cupping and appearance of cracks
Steamed or white beechHighly reactiveVery high (~ 0.38% per % of moisture)Excluded on underfloor heating, unacceptable winter shrinkage

The morphology of the wood element plays a major stabilising role in the face of hygrothermal stresses. Engineered multi-layer parquet, featuring a central batten core made of softwood or a cross-layered birch plywood backing, compensates for up to seventy percent of dimensional movements compared to an equivalent solid wood plank. This sandwich structure blocks the natural movement of the fibres and effectively prevents concave cupping during intensive heating periods. When the specification requires solid parquet, the width of the elements must imperatively remain moderate to subdivide the overall shrinkage over a greater number of joint lines. The parquet installer scrupulously applies the width-to-thickness ratio rule: on heated screed, too high a ratio increases the risk of surface tearing of the embedding screed under the effect of repeated tensile stresses.

Thermal operating limits and interface dimensioning

Standard SIA 253 sets the maximum permissible temperature at the surface of the flooring at 27 °C, a threshold beyond which accelerated desiccation deteriorates the cellular structure of the wood and the cohesion of polymer adhesives. This requirement demands fine regulation upstream and strictly governs the choice of material thickness. To guarantee efficient thermal diffusion without forcing the generator, the overall thermal resistance of the installed parquet must not exceed 0.15 m²·K/W. For dense oak, this thermal ceiling corresponds to a maximum permissible thickness of fifteen millimetres in solid wood. For a two- or three-ply engineered assembly, the total thickness commonly ranges between ten and fourteen millimetres, ensuring an ideal thermal compromise between inertia, heat transmission and mechanical rigidity.

The rigorous execution of glued installation constitutes the ultimate guarantee of the durability of the work under thermal stress. After having examined and analysed the heating commissioning report drawn up in accordance with the pre-installation temperature protocol, the parquet installer spreads a silane-modified polymer single-component adhesive using a suitable notched trowel, ensuring complete film transfer without the inclusion of heat-insulating air bubbles under the planks. The perimeter separation joints at the base of partitions and around door frames must provide a minimum movement reserve of ten to fifteen millimetres, guaranteeing free expansion in summer. Along the movement joints of the mineral substrate, the thermal break must imperatively be replicated in the parquet layout by an elastomeric mastic joint or a metal movement profile, preventing the shearing of elements installed across two differently regulated circuits.

Protocol for investigating thermal defects and protective measures

When a reactive timber species has been inadvertently selected for underfloor heating or when a thermal disruption occurs, mechanical symptoms appear quickly as soon as the first cold season arrives: shrinkage cracks wider than two millimetres, pronounced concave cupping of the planks, shearing of adhesive beads or cracking of the varnish at the edges. Faced with such defects, the parquet installer must under no circumstances undertake hasty repairs or sand a deformed flooring under thermal tension. The first imperative action consists in legally and technically freezing the situation through measurable and reproducible observations, prior to any mechanical modification of the work.

The investigation protocol begins with a methodical survey of contact temperatures by means of a contact thermometer or a calibrated infrared camera, by grid-patterning the pipe layouts and congested areas. The team leader simultaneously records the ambient humidity and the room temperature in order to assess the hygroscopic equilibrium point in accordance with standard SIA 253. As soon as the relative humidity of the room drops below 30% with a contact temperature greater than 27 °C, excessive shrinkage and tensile stresses are the direct consequence of a non-compliant operating climate and not an execution defect.

  1. Contradictory notification to the clientRecord all physical measurements (surface temperatures, air humidity, crack width) and notify in writing the observed exceedances with regard to the criteria prescribed by standard SIA 253.
  2. Immediate rectification of the ambient climateDemand from the agent the recalibration of the valves to limit the surface to 27 °C and the commissioning of humidifiers to restore a relative humidity of at least 35% to 50%.
  3. Suspension of all mechanical interventionCategorically prohibit hot sanding, filling of open cracks in winter or premature removal. Allow the wood to re-balance its dimensions after the heating is turned off before considering final repair work.

Frequently asked questions

Can beech or Canadian maple be laid on underfloor heating?

No, these species are formally contraindicated on heated screeds. Featuring a very high volumetric shrinkage coefficient and high reactivity, beech reacts abruptly to variations in hygrometry and temperature. Even in low thickness or as engineered parquet, the thermal gradient inevitably causes massive cracks during the winter period as well as pronounced concave cupping. Stable species with moderate shrinkage, such as oak or teak, should be systematically preferred.

What is the maximum permissible thickness for parquet on underfloor heating?

The total thickness of the glued parquet should not exceed 14 to 15 millimetres for solid wood, or 16 millimetres for a stable multi-layer product. This physical limit guarantees a thermal resistance lower than the ceiling prescribed by standard SIA 253, set at 0.15 m²·K/W. A greater thickness insulates the screed excessively, forcing the heating system to work harder to heat the room, which overheats the underside and unglues the planks.

Why is the surface temperature of the parquet limited to 27 °C?

According to technical recommendations and standard SIA 253, the heating point at the finished floor level must never exceed 27 °C. Beyond this contact temperature, the equilibrium moisture content of the wood drops below 5%, causing destructive shear stresses in the adhesive plane. This limit value also prevents the accelerated drying of the fibres, radial cracking and preserves the physiological comfort of the occupants by avoiding skin overheating.

What risks are presented by laying a thick carpet on heated parquet?

A dense or waterproof carpet traps ascending calories and creates a localised heat accumulation between the screed and the wood fibre. The surface temperature commonly exceeds 35 °C there, even with correct general regulation. This thermal confinement locally dries out the parquet drastically, generating spectacular differential shrinkage compared to cleared surfaces: the planks move apart, crack or delaminate solely under the influence of the furnishing textile.

Texts and standards cited

  • SIA 253Wooden flooring and parquet: design requirements, climatic tolerances and compatibility with underfloor heating

In the same section