Key takeaways
- Summer hygrometric expansion pushes the parquet tightly against the masonry due to a lack of sufficient perimeter clearance.
- Measuring the clearance under the skirting after removal is the key element of the joint inspection record.
- Sawing a relief joint with a plunge saw often allows the floor to flatten out again.
- The warranty for defects under SIA 118 assigns the costs to the defaulting flooring installer.
Diagnosis of dome buckling and measurement of perimeter clearance during the first humid summer
Installed during winter or early spring in a dry indoor climate induced by heating, solid oak parquet often exhibits a low equilibrium moisture content, close to 7 to 9%. As soon as summer arrives, the rise in ambient relative air humidity, regularly exceeding 70% in the Swiss temperate climate, causes the wood to absorb moisture. This inescapable physical phenomenon causes transverse swelling of the planks. If the prescribed perimeter clearance along walls and fixed elements was not left during glued or nailed installation, the parquet comes into mechanical contact with the masonry. Unable to expand horizontally, the flooring section undergoes axial compressive stresses that ultimately cause it to buckle upwards, creating a characteristic domed separation underfoot.
- Dome buckling
- Localized or generalized lifting of the timber flooring caused by the blocking of its lateral hygrometric expansion against the walls, creating a void beneath the planks with partial or total failure of the adhesive film.
Joint on-site inspection requires a rigorous method before any remedial work. The artisan or site foreman must immediately record ambient climatic conditions using a calibrated thermo-hygrometer, then measure the moisture content deep within the wood using an insulated-pin moisture meter. Visual observation of the lifting is not enough: the deflection at the centre of the room must be measured using a two-metre straightedge, followed immediately by opening up the edges.
- Methodical removal of perimeter skirtingsCarefully dismantle the wood or MDF skirtings around the entire perimeter of the affected area without damaging wall paints, marking their locations for subsequent re-installation.
- Metrological measurement of residual clearanceMeasure with a rule or feeler gauge the actual remaining gap between the last edge plank and the plaster, concrete or door frames around the entire perimeter.
- Identification of local blocking pointsLocate direct contact points where the wood is restrained against masonry, radiator pipes without a compressible sleeve, door frames or tile stops.
Edge relief sawing and allocation of warranty responsibilities
When diagnosis confirms zero residual clearance with direct contact against partitions, restoration requires mechanical perimeter decompression work. If the parquet has not split, shows no irreversible ridges or tongue-and-groove joint failure, relieving the edges in most cases allows the flooring to settle back down under its own weight or temporary ballasting.
- Marking out the relief lineMark a clean cutting line along the walls using a chalk line or laser, calibrated to re-establish a minimum reserve of ten to twelve millimetres, while checking that this width remains hidden by the thickness of the existing skirting.
- Plunge saw routing and dust extractionPerform perimeter trimming using a plunge circular saw mounted on a guide rail or a parquet trimming router, connected to a class M industrial vacuum cleaner to capture oak dust.
- Cleaning the kerf and checking settlementClear out wood offcuts and compressed plaster residues from the groove using a flat chisel, then check the gradual settling of the dome in the hours following the release of stress.
| Joint inspection record | Origin of the defect | Financial allocation for repair |
|---|---|---|
| Initial clearance zero or less than SIA 253 requirements, normal wood moisture in summer (11 to 12%) | Execution defect by the installer: failure to anticipate seasonal shrinkage and swelling | Total cost of repair borne by the parquet flooring contractor |
| Regulatory clearance respected during installation but filled with plaster left by another trade | Site interference: negligence by a third party unrelated to the parquet dimensioning | Costs passed on to the company responsible for filling the joint |
| Regulatory clearance used up by wood moisture exceeding 16% resulting from water damage or unsealed damp screed | Abnormal moisture supply not attributable to standard hygrometric dimensioning | Covered by the insurance for the damage or by the company responsible for the substrate |
From a legal and contractual perspective, the assumption of these works stems from contractual stipulations. When the construction contract is subject to SIA 118, the work benefits from a precise regime governing acceptance of the work, the time limit for giving notice of defects and the warranty. Lifting occurring during the first two years following acceptance constitutes a latent defect that manifests during the first climate transition. If opening the edges reveals that the parquet layer did not provide the clearance required by professional rules, the client is entitled to demand the elimination of the defect free of charge. The contractor then assumes responsibility for sawing repairs, reinstalling skirtings, and localized re-gluing of lifted sections. For any questions regarding the overall cost estimate of such repair work, please refer to the /tenders/ section.
Edge repair routing and mechanical remediation of the flooring
When the compression dome has been relieved by an initial relief cut, permanent stabilization of the solid oak parquet requires methodical reworking of the periphery. Planks that have pushed against partitions or door frames must regain an expansion margin in accordance with good workmanship. The operation begins with the careful removal of the skirtings, which traditionally fall under carpentry work but whose removal conditions direct access to the perimeter joint.
- Removal and marking of skirtingsRelease the perimeter skirtings using a flat crowbar and a sacrificial block so as not to mark the plaster or crush the edges of the wood. Number each element on the back to facilitate subsequent reinstallation by the carpenter or parquet layer, noting glued or nailed fixings on lightweight partitions.
- Measurement of residual clearance and marking of the cutting lineMeasure residual clearance using a feeler gauge or metal rule around the entire perimeter. In the case of a summer dome, this clearance has generally dropped to zero millimetres along several lengths. Mark a continuous reference line ensuring a net clearance of at least fifteen millimetres between the edge of the last plank and the finished masonry facing.
- Trimming router work with dust collectionExecute the cut along the walls using a plunge-guided trimming saw or a specific angle router for parquet layers. Set the depth stop to the exact thickness of the plank so as not to gouge the screed or cut a resilient strip. Connect the tool to an industrial vacuum cleaner with an appropriate filtration filter class to collect fine oak dust directly at the source.
- Vacuuming joint bases and flatness checkClear the created void of all chips, plaster residues and rubble using a flat vacuum attachment. Allow the floor to settle under its own weight or apply provisional loading wedges if full-surface bonding shows partial loss of adhesion requiring re-injection of resin.
In situations where the dome is accompanied by the tearing away of the adhesive bed on a cement screed, simple perimeter cutting is not always sufficient to re-establish perfect flatness. A check with a two-metre straightedge verifies that the residual deflection has subsided. If planks sound hollow after mechanical release, discreet four-millimetre diameter drilling in the joints allows pressure injection of a fluid polyurethaneurethane adhesive or solvent-free epoxy resin to restore adhesion to the substrate.
Application of SIA 118 and SIA 253: arbitration and cost allocation
The lifting of solid parquet during the first warm season is the typical defect of broken hygrometric equilibrium. When the work is subject to Swiss construction contractual conditions, the management of this damage revolves around SIA 118 for procedural warranty aspects and SIA 253 for execution requirements specific to bonded floor coverings.
| On-site technical findings | Qualification of the defect | Reference standard | Financial liability |
|---|---|---|---|
| Total absence of perimeter joint measured under removed skirtings | Direct execution defect by the installation company | SIA 253 standard | Borne exclusively by the parquet layer (repair, skirtings and finishes) |
| Perimeter clearance of ten millimetres filled by ambient humidity exceeding 75% over several weeks | Misuse or abnormal climatic conditions of the inhabited building | SIA 253 standard | Borne by the client or operator |
| Excessive moisture originating from the lower slab without prescribed vapour barrier | Design error or incomplete specification by the site management | SIA 118 standard | Borne by the representative or site management |
| Floor heating commissioning omitted or undocumented prior to bonding | Failure in substrate preparation prior to finishing work | SIA 253 standard | Shared between site management and the installer without formal notice |
According to SIA 118, notice of defects must be given by the client as soon as the dome is discovered. During the legal two-year warranty period for apparent or latent defects occurring after acceptance, the contractor has the right and obligation to eliminate the defect at their own expense if their liability is established. If the absence of perimeter clearance is attested by a joint inspection report, the parquet layer cannot invoke exceptional air humidity: SIA 253 requires anticipating the maximum transverse expansion of the wood according to room geometry.
When joint expertise demonstrates that the perimeter clearance provided in the initial specification was restricted by the subsequent installation of heavy fittings or linings not coordinated by site management, financial liability shifts to site coordination. In all cases, costing for the complete repair work, including replacement supplies and finishing labor, must be established according to official finishing work tender pricing schedules.
Attribution conflict and joint expert appraisal protocol
When the dome persists despite an initial relief cut or site management refuses to approve the repair on a time-and-materials basis, dispute management must be formalized immediately. In the presence of solid oak restrained against masonry during the first summer, the reflex is to freeze the technical situation before any further alteration of the parquet. The company requests a joint on-site visit to record the condition of the floor, the ambient climate and the chain of causes.
- Joint environmental recordMeasure and record relative air humidity, room temperature, as well as residual mass moisture of the wood and screed in the report according to SIA 253 requirements.
- Destructive sounding under skirtingSpot remove skirtings in the presence of site management to measure the remaining perimeter clearance at critical blocking points using a calliper.
- Formal warranty notificationInvoke SIA 118 claim rules to determine whether the lifting stems from an installation defect by the installer or abnormal climatic conditions imposed by operation.
In the event of persistent disagreement on the origin of the buckling, the parties appoint a neutral expert from the Western Swiss flooring installation branch. As long as the joint inspection record is not signed, the parquet layer refrains from completely dismantling the work: only peripheral relief sawing under vacuum is performed to stop destructive pressure on partition walls.
Frequently asked questions
Is edge sawing always sufficient to make detached solid parquet settle back down?
Not systematically. If the oak has buckled without breaking the adhesive, releasing the edge allows the parquet to regain its flatness within a few days under its own weight. Conversely, if the adhesive has suffered detachment or cohesive failure of the screed, the planks remain hollow when walked upon. A consolidation resin must then be injected under the hollow-sounding areas after re-establishing perimeter clearance in accordance with SIA 253.
What width of perimeter joint must be reserved during repair routing?
Repair requires a minimum clearance of 10 to 15 millimetres relative to the bare masonry, in accordance with good workmanship for solid wood. Cutting with a rail-guided plunge saw must take into account the covering thickness of the existing skirting. If this skirting only covers 12 millimetres, the edge must be routed under its coverage or a counter-skirting installed to hide the joint while ensuring expansion.
Who is responsible for removing and reinstalling skirtings in the event of damage?
Removing skirtings falls under carpentry work. If the parquet layer is found responsible for the lack of perimeter clearance under SIA 118, the resulting costs for removal, fitting and reinstallation by the carpenter form part of the consequential damage chargeable to them. If the swelling is caused by water damage or poor building ventilation by the user, all interventions are invoiced to the client.
How to record a client's refusal to ventilate during the first summer?
The contractor sends a formal written notice as soon as they observe hygrothermal conditions outside tolerance ranges. According to SIA 253, the indoor climate must be between 30% and 65% relative humidity. If the new building remains closed all summer with a humidity level exceeding 75%, the parquet layer records these values in their daily report and disclaims liability for foreseeable dimensional deformations of the oak.
Texts and standards cited
- norme SIA 118General conditions for the execution of construction work, governing acceptance of the work, notice of defects and the exercise of warranty rights.
- norme SIA 253Bonded floor coverings, defining the technical rules for parquet installation, sizing of perimeter clearances and permissible moisture tolerances.
