Formwork: panel forms, form linings and fair-faced concrete quality: execution reference guide
Aimed at site chargehands, foremen and site managers, this section compiles execution rules for successful reinforced concrete fair-faced finishes according to SIA 262 and SIA 118 standards. From form lining selection to panel clamping, it details practical methods to prevent surface defects, ensure joint tightness and guarantee the stability of formwork systems on Swiss structural work construction sites.
- 10chapters
- 22 000words
- 6sections in the training course
- 60chapters in total
Key values to remember 4
100 cm
Minimum top rail height for formwork platform edge protection
15 cm
Minimum height of edge protection toeboards on working platforms
47 cm
Maximum spacing between horizontal elements of edge protection
2 m
Free fall height requiring the installation of edge protection
Technical scope of formwork and fair-faced finishes
This section exclusively addresses formwork as a tool for shaping the structure and determining the final concrete finish. It governs the mechanical behaviour of vertical or horizontal formwork, panel layout, release agent application and arris geometry. The visual and structural success of a fair-faced finish depends directly on system rigidity, the control of fresh concrete hydrostatic pressures and the absolute tightness of joints on the construction site.
| Element handled | Key technical requirement | Service boundary (out of section) |
|---|---|---|
| Form linings and panel forms | Surface planarity and rigidity under pressure | Overall dimensional check and setting-out tolerances |
| Release agents (oils) | Uniform film without accumulation or staining | Chemical setting behaviour of cement |
| Jointing and sealing strips | Absolute prevention of grout leakage | Remediation of gravel pockets by patching |
| Tie rods and spacers | Symmetrical layout and watertightness of penetrations | Overall tanking waterproofing performance |
Managing fresh concrete pressure requires constant vigilance regarding stabilisation and closing devices. In accordance with OTConst, measures must be taken at workstations and walkways so that workers are not endangered by the collapse of building elements or falling materials. Poorly anchored, undersized formwork or formwork destabilised by wind exposes personnel to major risks during pouring.
Execution sequence and chapter structure
To ensure achieving the ordered fair-faced finish without costly remedial work, the supervisory team must approach formwork according to a rigorous chronological sequence, from panel preparation through to pre-pour inspection. Each phase directly governs the next, from the contact surface through to cast-in finishing elements.
- Preparation and contact interface (A2-01 to A2-03)The choice of panel determines the rough or smooth finish according to the classes specified by standard SIA 262. Controlled application of the release agent prevents blowholes and surface dusting. Sealing joints prevents grout leakage responsible for arris defects.
- Erection, stability and penetrations (A2-04 to A2-06)Bracing and wind propping secure the panel form system. A regular tie-rod layout ensures symmetrical spacer holes while enabling durable plugging. High-rise walls use climbing brackets to sequence pour lifts safely.
- Specific structures and high-quality finishes (A2-07 to A2-10)Timber formwork shapes complex curves and angles. Chamfer strips create clean construction joints. Opening cleanout openings at the base ensures debris removal before pouring, whilst insulating permanent formwork eliminates thermal bridges on façades.
Formwork must have sufficient rigidity to withstand loads due to concreting and maintain the tolerances required for the finished structure, without deflection detrimental to the appearance or function of the structure.
Norme SIA 262
📘 Chapters in this section 10
Selecting formwork lining: what the specified finish requires
Identify the ideal panel according to fair-faced concrete classes to meet the requirements of the specifications.
Formwork: wall forms, form liners and surface finish qualityFormwork release agent: application rate, application and defects caused by excess
Spray the correct dosage of oil to permanently eliminate blowholes, marbling and surface chalking.
Formwork: wall forms, form liners and surface finish qualityFormwork joint tightness: preventing grout loss
Neutralise grout leakage using suitable compressible foam profiles to preserve concrete compaction.
Formwork: wall forms, form liners and surface finish qualityShuttering panel stability: propping, ballasting and wind load
Calculate the push-pull propping and ballasting required to stabilise panel forms against wind gusts.
Formwork: wall forms, form liners and surface finish qualityTie rods and formwork tie holes: layout and neat sealing
Set out tie rods and plug tie holes watertight for an impeccable finish.
Formwork: wall forms, form liners and surface finish qualityClimbing formwork: lifting a high-rise wall in pours
Organise climbing brackets and anchor pinning to erect vertical walls in successive lifts.
Formwork: wall forms, form liners and surface finish qualityTraditional timber formwork: curved shapes, angles, and custom profiles
Assemble curved templates and bespoke timber framing to successfully achieve non-standard geometric shapes.
Formwork: wall forms, form liners and surface finish qualityEdges, chamfers and slab edges: making them neat and protecting them
Fix straight nailed chamfer strips to achieve sharp arrises and protect slab edges.
Formwork: wall forms, form liners and surface finish qualityCleaning formwork bottoms: clean-out openings and final inspection
Cut cleanout openings at the base to remove sawdust and tie wire before authorising the wall pour.
Formwork: wall forms, form liners and surface finish qualityInsulated permanent formwork: installation, insulation continuity and fixing
Install integrated insulation modules seamlessly to ensure thermal continuity and mechanical bonding with the concrete.
