Key takeaways
- Tie rod layout requires horizontal and vertical alignment coordinated with formwork panel joints.
- End sealing cones must ensure a clean profile without tearing the surface skin when stripping formwork.
- Sealing with non-shrink mortar prevents crazing and deep debonding of the plugging element.
- Colour matching of the plug requires preliminary trials to match the shade of the surrounding face.
Layout of tie rods and geometry of formwork tie holes
On a fair-faced finish, the distribution of tie rods does not merely resist the hydrostatic pressure of fresh concrete during pouring. The through-holes form a predominant geometric pattern that sets the rhythm of the finished wall surface. A disordered arrangement, resulting from mismatched panel assemblies or uncoordinated ad-hoc drilling, immediately degrades the visual perception of the finished work. The position of each tie hole must be defined on the formwork layout drawings before erecting steel or timber panels.
The drill holes must align strictly along vertical and horizontal axes, respecting symmetry in relation to the wall edges, window openings and construction joints. The use of single-use spacers with PVC or fibre-cement tubes requires the installation of watertight end-bearing cones. These cones prevent grout loss along the spacer tube, which would cause dark halos or gravel pockets around the orifice. They also leave a regular geometric recess at least 20 to 30 mm deep, which is essential for the mechanical anchoring of the patch plug or precast cap.
| Formwork type | Tie rod grid | Alignment tolerance | Cone recess depth |
|---|---|---|---|
| Standard steel formwork panel | Fixed grid determined by stiffeners | ± 3 mm along the datum line | 15 to 20 mm |
| Custom timber frame formwork | Flexible layout aligned with the panel | ± 2 mm from the setting-out drawing | 25 to 40 mm |
| Climbing or tall formwork | Reinforced grid at the base of the lift | ± 5 mm over the total height | 30 to 50 mm |
Plugging techniques: sealing, shrinkage control and colour uniformity
The treatment of formwork tie holes on fair-faced concrete requires a rigorous methodology to prevent water infiltration, avoid internal oxidation and preserve visual continuity. Complete sealing includes a watertight barrier in the core of the wall and a surface finish that is either flush or slightly recessed. Depending on architectural requirements, finishing is carried out either by bonding a precast concrete plug of the same mix as the wall, or by carefully dry-packing with a non-shrink proprietary mortar.
- Cone removal and cleaningExtract the formwork cones without damaging the sharp edges of the circular recess using a suitable extractor. Blow dust out of the tube with compressed air and remove any release agent residue.
- Installation of the central waterproof barrierInsert an expanding rubber sealing plug into the centre of the wall thickness or inject a waterproof resin to interrupt capillarity completely through the external wall.
- Pre-wetting and bonding slurryDampen the cavity to refusal without leaving standing water, then apply a bonding slurry to neutralise suction from the hardened concrete substrate.
- Tamping the non-shrink mortarMix a shrinkage-compensated grouting mortar to an earth-moist consistency, then tamp firmly in successive layers with a metal drift pin to eliminate all voids.
- Finishing and colour adjustmentStrike off excess flush with a spatula or apply the grooved concrete plug of matching shade, then maintain moist curing for forty-eight hours to prevent premature drying out.
The shade of the plugging mortar represents the main challenge on fair-faced concrete. As it dries, a traditional hydraulic mortar based on grey cement becomes markedly darker than the surrounding wall, due to the low local water-cement ratio and hand compaction. To adjust the final colour, the plugging formulation frequently combines a defined proportion of white cement and standard grey cement, blended with quartz sand whose grading matches the fines in the wall matrix. Test specimens made in an inconspicuous area determine the exact mix design after full drying.
The contractor executes the work in accordance with the contract, the recognised rules of their trade and the drawings approved for construction.
norme SIA 118
Coordination of tie rod layout with reinforcement and joints
On a fair-faced finish, tie rod positioning is never improvised when tightening formwork panels. The pattern of tie holes forms a permanent visual grid that must harmonise with panel joints, stop-ends and reinforcement positions. A clash between a rod and a stirrup inevitably results in moving a hole with a rotary hammer drill or slanting a spacer, creating grout leakage or misalignment that destroys visual regularity.
To prevent this defect, the formwork drawing showing the precise tie rod layout is overlaid on the reinforcement drawing right from the work preparation phase. Vertical and horizontal layers are adjusted with spacings shifted locally by 20 to 30 millimetres to let spacers pass freely through the wall, without direct contact between reinforcing steel and the PVC or fibre-cement tube.
| Wall configuration | Critical visual constraint | Recommended layout arrangement | Execution measure on formwork |
|---|---|---|---|
| Internal fair-faced concrete wall | Strict horizontal alignment with windows and penetrations | Regular grid aligned with the storey height | Systematic plugging of unused formwork holes with screwed watertight plugs |
| Tall facade wall | Vertical visual continuity across construction joints | Grid alignment picked up by cast-in master tie or laser reference | Installation of blind cones for scaffolding hangers or brackets |
| Perimeter or retaining walls | Consistent rhythm breaking the monotony of long runs | Symmetry in relation to expansion joints | Use of fixed spacing jigs on formwork panel ends |
When the layout drawing requires blind holes to preserve symmetry without piercing through the wall (for instance at wall heads or against existing shoring), dummy cones are fixed directly to the steel or timber skin to imprint the exact recess without compromising the water-tightness of the structure.
Plugging application: setting, texture and handover inspection
Final sealing of tie holes on fair-faced concrete tolerates no improvisation on the construction site. To guarantee water-tightness, acoustic insulation and surface perfection, the sealing system combines an internal structural element and a finishing plug. Precast concrete cores or plugs represent the most durable solution to match the colour of the cast wall.
- Cone removal and cleaningRemove end cones immediately after striking formwork using a suitable extractor, without chipping the concrete edges. Blow dust out of the hole with dry compressed air and remove all traces of residual release agent from the chamfer.
- Plugging the wall coreInsert an elastomeric compression sealing plug in the centre of the tube or place non-shrink micro-concrete of plastic consistency to guarantee core airtightness and sound insulation.
- Bonding the architectural plugApply a resin or zero-shrink fluid mineral adhesive compatible with concrete. Insert the precast core, whose aggregate composition and cement match those of the reference wall.
- Depth setting and finishingSet the recess depth using a calibrated spacer block. Immediately wipe binder smears from the chamfer with a damp sponge, without rubbing the fair-faced concrete surface to avoid opening up pores.
The contractor ensures that the materials used cause no oil bleeding, oxidation or white efflorescence over time. If the client notes deviations in flatness, clashing colour tones or debonding, contractual remedies are exercised under the standard rules of the contract for work regulated by the Code of Obligations (CO), particularly when the client notifies defects after delivery of the structure.
Remedying plugging defects and repairing fair-faced concrete
On a fair-faced concrete finish, non-compliance of a tie hole is immediately noticeable: dark halo caused by over-rich or poorly dried mortar, white efflorescence patch, circular halo caused by a plastic cone left in place, or peripheral debonding due to hydraulic shrinkage. When these defects appear after striking and drying, the foreman must not improvise surface patching that would only worsen the visual inconsistency. Any corrective action requires a surgical approach to preserve the flatness and texture of the plain concrete.
- Shrinkage or debonding of mortar: completely cut out the defective plug with a light chisel or core drill, remove dust, moisten the substrate to refusal without standing water, then reapply a shrinkage-compensated non-shrink mortar.
- Oil or rust stains: remove contamination coming from rods by dry wire brushing or by applying a specific solvent-based poultice, prior to patching with a colour-matched mortar.
- Noticeable colour difference: produce trial coupons on the construction site by varying the grey/white cement ratio and quartz fines, allowing them to dry for at least 48 hours to assess the final shade under raking light.
- Protruding or recessed plug: grind flush with a fine diamond block for high spots, or cut back by at least 15 mm before remaking to avoid thin featheredges that flake away.
If the dispute concerns a flagrant geometric deviation from the layout or a repair that cannot be made without disfiguring the structure, contractual dialogue is necessary. Pursuant to art. 365 CO, if the material supplied by the client or the ground designated by him is found to be defective, or if any other circumstance arises which compromises the proper or timely execution of the work, the contractor shall immediately inform the client. This formal step, supplemented by the rules of SIA 118, makes it possible to rule on aesthetic acceptability or the application of a surface-harmonising mineral treatment approved by the site management.
Frequently asked questions
How can dark haloing around plugged holes be avoided?
Halos often result from moisture migration or excess polymer in the patching mortar. The perimeter should be moistened without saturating the outer face, a non-shrink thixotropic mortar mixed with a binder similar to the poured concrete should be used, and the chamfer neatly defined with a precast concrete plug of the same composition.
Can the plastic spacer cone be left inside the wall?
No. On fair-faced concrete, the plastic cone prevents adhesion of the patching mortar and creates a permanent thermal and visual line over time. It must systematically be removed with an extraction tool before cleaning the recess, to allow direct bonding of the mortar or concrete plug onto the mineral substrate.
How can straight alignment of tie rods over a great height be guaranteed?
Positioning depends on the assembly accuracy of the steel formwork panels. Panels must be clamped rigidly together, slotted holes aligned using watertight infill profiles, and tie positions checked with a rotary laser before final tightening. Tie layout continuity from one lift to the next must be guided by a strictly transferred datum line.
What solution should be chosen for a through tie hole subject to pressurised water?
To guarantee water-tightness in a basement wall, a hydrophilic or mechanically expanding rubber sealing plug is inserted into the centre of the sleeve. Both ends are then filled with a waterproof non-shrink mortar to a depth of at least 50 mm, before potentially fitting an architectural face plug on the external surface.
Texts and standards cited
- CO art. 365materials and ground: the contractor is liable for the quality of the materials supplied; if the material supplied by the client or the ground designated by him is found to be defective, or if any other circumstance arises which compromises the proper or timely execution of the work, he shall immediately inform the client, on pain of bearing the consequences (para. 3).
- norme SIA 118General conditions for construction works governing rights, obligations and handover of works between client and contractor.
