Skip to content
Website
🧱 CFC 211.1Slabs, floors and precast half-slabsChapter 3 of 10 in the section

In-situ cast solid slab: thickness, span and span direction

This chapter details determining the span directions of an in-situ cast concrete solid slab and the rigorous sequencing of reinforcement. You will learn to identify the main bending direction, position top layers without error on their spacers, and check the specified thickness at bearing zones on walls.

Key takeaways

  • The main span dictates the position of the bar closest to the surface.
  • Formwork thickness directly determines the effective depth and final slab strength.
  • Inverting two top reinforcement layers dangerously reduces the calculated lever arm.
  • Direct bearing on walls requires rigorous steel anchorage according to standard SIA 262.

Determining span direction and placing the top reinforcement layer

On formwork and reinforcement drawings, support geometry dictates the mechanical behaviour of the solid slab. For a slab on continuous linear supports, the ratio between the longer length and the shorter length indicates whether the structure acts in one-way or two-way bending. As soon as the ratio exceeds two, the load transfers almost entirely along the shorter span. The civil engineer then designs the main steel cross-section perpendicular to the long supports.

Effective depth (d)
Distance between the extreme compression fibre of the concrete cross-section and the centre of gravity of the tensile reinforcement. Any reduction in this distance reduces bending resistance.

Over support zones or across continuity over shear walls, bending moments are negative and induce tension in the upper section. The steel fixer must imperatively position the main steel layer as high as possible, directly beneath the concrete cover specified by standard SIA 262. The secondary distribution layer is systematically placed below this main layer.

  1. Identify the load-bearing directionIdentify on the bar schedule and layout drawing the direction corresponding to the maximum bending moment, generally perpendicular to the supporting wall.
  2. Place reinforcement spacersArrange steel chairs or continuous spacers on the bottom layer with stable spacing to prevent any sagging under foot traffic.
  3. Thread the top load-bearing layerPlace the load-bearing bars or mesh directly onto the top line of chair spacers, at the level closest to the top surface of the rough concrete.
  4. Tie the distribution reinforcementFasten the distribution bars below or above the main layer in strict accordance with the engineer's detail section.

Checking specified thickness and bearing onto supporting walls

The specified thickness of a solid slab results from a strict balance between permissible deflection criteria in the serviceability limit state and ultimate resistance. The site manager verifies the finished level relative to the one-metre datum mark on the load-bearing walls. Slab soffit formwork positioning must compensate for any anticipated camber deflections during concreting.

Indicative orders of magnitude for simply supported solid slabs
Clear span (L)Usual indicative thicknessTop main reinforcement over supportCritical inspection point
4.00 m to 5.00 m18 to 20 cmPerpendicular to load-bearing wallSpacer height and nominal cover
5.50 m to 6.50 m22 to 25 cmPerpendicular with reinforced top barsOverturning stability of chair spacers
7.00 m to 8.00 m26 to 30 cmConcentrated on support stripsTying density and risk of settlement

The support zone on a wall requires meticulous geometric care. The minimum bearing width of slab concrete on the bare wall head guarantees transmission of diagonal compression struts. If the wall head exhibits batter or a defective nib, the effective bearing surface is reduced, inducing stress concentrations likely to spall the edge.

Reinforcement must be positioned and secured so as to ensure its position during concreting and ensure adequate stress transfer between steel and concrete.

norme SIA 262

Identifying negative moments and top bar hierarchy

In a reinforced concrete solid slab, the vertical position of bars within the reinforcement layout directly determines resistance to bending moments. While in the span the load-bearing steel is placed lowest to maximise the lever arm, over a continuous support tension shifts to the upper fibres. Under the principles of standard SIA 262, steel resisting support moments must occupy the highest possible position in the slab, just beneath the specified cover.

Relative position of layers by zone and stress type
Slab zoneDirection consideredBar positionMechanical function
In span (bottom zone)Main load-bearing directionLayer 1 (in contact with spacers)Maximum mid-span tension
In span (bottom zone)Secondary / distribution directionLayer 2 (crossed above layer 1)Transverse load distribution
Over continuous support (top bars)Main load-bearing directionLayer 4 (highest under cover)Support tension (hogging moment)
Over continuous support (top bars)Secondary / transverse directionLayer 3 (slid under layer 4)Assembly and longitudinal tying

Formwork setting out must clearly show the span direction before placing support chairs. Assembly stirrups or mesh chair spacers must provide a stable base capable of supporting foot traffic from formworkers and steel fixers without crushing the top layer. Any sagging reduces the effective static depth defined by the civil engineer.

Anchorage on supporting wall, continuity, and thickness tolerance

Transferring shear forces and partial encastrement moments requires a precise bearing depth on the lower wall. A slab bearing on a reinforced concrete wall cannot rely on mere edge contact: the bottom layer must extend beyond the centreline of the wall to engage the support compression strut in accordance with standard SIA 262.

  1. Checking edge formwork on the wall headInspect cleanliness of the construction joint and set out stop-ends or side edge formwork, ensuring that rough bearing on hardened concrete is not reduced by out-of-plumb lower formwork panels.
  2. Placing spacers and the bottom layerLay certified non-deformable spacers. Push straight bars or hooks of the bottom layer to the outer face of the end wall, maintaining the specified side cover.
  3. Installing top layer supportsPlace ribbed wire chairs or steel support strips spaced at 80 cm maximum to prevent any reinforcement deflection during site traffic and pouring.
  4. Finished thickness level checkCheck clear height between formwork soffit and finished level using a dipstick or rigid gauge. Any deviation exceeding allowable tolerances alters structural thickness and overall dead load.

The contractor ensures that the thickness specified on drawings is scrupulously maintained across the entire area. In the event of a thickness defect or non-compliant cover prior to concreting, art. 365 CO al. 3 states that if the material supplied by the client or the site designated by them is found to be defective, or if any other circumstance jeopardises the proper or punctual execution of the work, the contractor shall immediately inform the client. To ensure collective safety during these formwork and reinforcement operations, workers use personal protective equipment according to art. 82 LAA, which stipulates that the employer must take, to prevent occupational accidents and illnesses, all measures shown by experience to be necessary, applicable according to current technical knowledge, and suited to the prevailing conditions, while workers shall assist the employer.

Managing thickness deviations and top reinforcement errors

On an in-situ cast floor slab, an error in specified thickness or an inverted direction of top reinforcement directly impairs the load-bearing capacity of the structure. Inverting layers at supports alters the internal lever arm $d$ calculated according to SIA 262. When the main layer is placed beneath the distribution layer, flexural resistance over the support drops drastically, while the risk of premature cracking rises in the tension zone.

If reinforcement is already tied and a non-compliant span direction or defective minimum wall bearing is discovered, the foreperson immediately halts the installation of penetrations and alerts the site management. Under art. 365 CO, the contractor immediately informs the client of any circumstance jeopardising the proper or punctual execution of the work. Manual reworking of top bars remains mandatory before concreting: invert layers by lifting the chair spacers and realign top bars in the direction of the actual span.

If formwork thickness is non-compliant, adjusting edge jacks and formwork panels is required to restore the rough dimensions before casting. If casting has started or was completed with confirmed under-thickness, no construction site surcharge load may be applied. The civil engineer must be consulted to recalculate the residual section according to SIA 262. Art. 229 CP punishes anyone who, in directing or executing a construction project, intentionally or through negligence breaches recognised building rules and knowingly endangers the life or physical integrity of persons. Depending on the structural evaluation, corrective measures mandated by project management will range from carbon-fibre plate bonding to demolishing the non-compliant span.

Frequently asked questions

What should be done if top bars touch the edge formwork on the wall?

Installation must be stopped immediately and cut steel lengths checked. A top bar must never contact the stop-end directly in order to guarantee the concrete cover specified by SIA 262. The solution consists in trimming bars with shears or rebending the ends to ensure the required clearance before concreting.

How is a top layer placed in the wrong direction corrected before concreting?

Tie wires across the affected span must systematically be undone. The foreperson has the transverse top layer bars removed, reinstalls the longitudinal main bars directly on proper chair spacers, then replaces the distribution layer on top. This operation ensures the design lever arm required by the engineer over the wall support zone.

What is the consequence of a 15 mm slab under-thickness discovered during casting?

Reduced thickness significantly diminishes section inertia and increases long-term deflections, while risking a reduction of regulatory concrete cover for top steel. Site management must halt the subsequent phase. The civil engineer analyses load capacity according to standard SIA 262. If structural safety is compromised, bonded reinforcement or complete reconstruction becomes mandatory.

How is the minimum bearing of a solid slab on a panel-formed wall verified?

Before closing edge forms, the foreman measures the actual bearing depth of the formwork soffit and reinforcement lap onto the hardened concrete of the wall. Rough bearing must match the civil engineer's execution drawings strictly. In case of insufficient bearing, supplementary stitch reinforcement or an widened support must be formally approved.

Texts and standards cited

  • norme SIA 262Technical standard for reinforced concrete structures, defining internal lever arm calculation, reinforcement detailing, and concrete cover requirements.
  • CO art. 365Materials and site: the contractor immediately informs the client if any circumstance jeopardises the proper or punctual execution of the work (al. 3).
  • CPBreach of the rules of building: provides a penalty for anyone who breaches the rules of building and knowingly endangers the life or physical integrity of persons.

In the same section