Skip to content
Website
🧱 CFC 211.1Slabs, floors and precast half-slabsChapter 9 of 10 in the section

Slab surfacing: power floating, trowelling and finish level to declare

This chapter provides the technical benchmarks to define, plan, and execute the surfacing of a reinforced concrete slab. You will learn to identify the ideal intervention window, specify the finish level suited to the requirements of standard SIA 414, and prevent interface defects with subsequent floor coverings or screeds.

Key takeaways

  • The raw, power-floated, or trowelled surface finish directly dictates the adhesion of subsequent layers.
  • Mechanical power floating starts as soon as surface footprints do not exceed five millimetres.
  • Standard SIA 414 governs the flatness tolerances applicable to slab substrates.
  • Unsuitable surfacing generates heavy subsequent costs for grinding, shot blasting, or compensatory levelling compound.

Define the finish level according to the intended use of the structure

On a structural work construction site, the upper surface of a reinforced concrete slab cannot be treated uniformly without prior consultation. The finish level must be expressly ordered and coordinated with the requirements of the subsequently intervening trade. Standard practice distinguishes three main states: the raw screeded finish, the power-floated finish, and the mechanically trowelled finish. Each of these states meets precise physical constraints and engages the responsibility of the masonry contractor towards the finishing work contractors.

Classification of surface states and compatibility with subsequent trades
Finish levelPrimary toolResulting textureTypical application for the subsequent trade
Raw screededLevelling rule, vibrating screedRough, striated, loose laitanceBonded screed, cast-in-place slope concrete
Mechanically power floatedPower float with pan/discClosed, flat, slightly granularBituminous waterproofing, thermal insulation
Helicopter trowelledTilted finishing bladesBurnished, dense, closed without asperitiesFinished slab for car parks, direct resin

The overall and local flatness of the finished surface is governed by standard SIA 414. This standard sets the permissible deviations under the 2 m and 20 cm straight edge according to the requested class. Under art. 365 CO, if a discrepancy arises between the formwork drawings, the tender specification, and the actual use of the room, the contractor shall immediately inform the client through written notice in order to clarify the required level before casting.

Mastering the setting window and the kinematics of mechanical passes

Mechanical surfacing relies on rigorous management of the concrete's setting time. Intervening too early causes tearing of the paste, sinking of the equipment, and excessive accumulation of laitance slurry on the surface. Intervening too late makes compaction impossible and leads to rapid scaling under the effect of construction site traffic. The open window depends on ambient thermal conditions, wind, and the hydration kinematics of the binder.

  1. Evaporation of bleed waterAfter screeding and vibrating the slab, allow the bleed water to evaporate completely. Never float a surface covered with a film of free water, as this will irreparably weaken the surface zone.
  2. Monitoring penetration resistanceThe site foreman checks the firmness of the concrete by walking on it. The operator can set foot on the slab: the footprint left by the safety boot must not exceed 3 to 5 mm in depth.
  3. First roughing pass with the float panMount the float pan onto the power float. Make a first cross pass at moderate speed to knock down screed ridges, close aggregate pockets, and homogenise the paste.
  4. Finishing passes with bladesRemove the pan to work directly with the metal blades. Gradually increase blade pitch and rotational speed as the concrete hardens, until the desired sheen is obtained.

Once the operation is complete, the appearance of plastic shrinkage microcracks must be prevented by installing suitable temporary curing protection. In the absence of specifications in the quote, art. 363 CO governs the contractor's obligation to deliver a structure fit for its intended use. The structural work self-inspection report must record the finishing time of the trowelling, the visual condition obtained, and the tolerances measured before handing over the construction site to the subsequent trade.

Contractual surface specifications and tolerances according to standard SIA 414

The surface of a reinforced concrete slab cannot be described merely with informal adjectives. The delivery condition must meet the geometric requirements of standard SIA 414 as well as the terms of the work contract. A raw screeded state, mechanical power floating, or dense trowelling constitute distinct structural services. The absence of an explicit contractual specification refers by default to normal execution tolerances, which are often incompatible with the direct application of thin floor coverings or bonded waterproofing.

Slab surface finish levels and compatibility with finishing work trades
Finish levelSurface appearance and textureDeviation under the 2 m straight edgeDestination and compatible subsequent trades
Raw screededRough, striated, surface laitance presentNormal tolerance according to standard SIA 414 (± 8 to 10 mm)Unbonded screed, thermal or acoustic floating screed (CFC 281)
Mechanically power floated (with pan)Closed grain but porous, open for adhesionPrecise tolerance according to standard SIA 414 (± 4 to 5 mm)Bonded screed, bituminous waterproofing with primer, thick levelling compound
Mechanically trowelled (with blades)Closed, dense, burnished or steel-trowelled appearancePrecise or strict tolerance according to agreementDirect use (technical slab, car park, storage) without an applied wearing course

Impact of surfacing level on finishing work interfaces

The choice of surfacing dictates the preparatory operations imposed on subsequent trades. A slab delivered with excessive trowelling prevents the direct mechanical keying of a mortar or resin. Conversely, a raw slab necessitates compensatory material or re-profiling, generating excess thickness and level discrepancies at door thresholds and technical service ducts.

  • Substrate for bonded screed: concrete requires controlled roughness obtained by power floating without superficial burnishing. An over-closed surface traps fines and creates a fragile skin that necessitates subsequent shot blasting or planing.
  • Substrate for roof or foundation slab waterproofing: the surface must be free from gravel pockets, sharp edges, and float ridges likely to puncture bituminous or synthetic sheets during laying.
  • Slab for direct use without covering: mechanical compaction with blades must close the surface porosity to limit dusting and increase abrasion resistance in technical rooms or parking areas.

Coordination between the civil engineer, the structural work, and the flooring installers remains crucial from the tender phase onwards. When a reinforced concrete slab replaces a screed with a finished surface treatment, the site manager must verify the compatibility of drainage slopes, block-outs for floor drains, and movement profiles. The joint inspection record prior to the intervention of the subsequent trade allows the condition of the substrate to be frozen and geometric reservations to be cleared.

Managing surfacing deviations and remedies during the execution phase

Non-compliant surfacing directly compromises finishing work interfaces. When a slab shows lippage, mechanical surfacing ripples, or late bleeding that has soaked the cement paste, supervisory staff must react immediately to limit remedial intervention costs.

When concrete is closed too early, surface blistering or delamination requires mechanical diagnosis using a rebound hammer or localised core sampling. The appearance of excessive burnishing prevents direct adhesion of a bonded system, while a slab left too rough transfers excessive thicknesses onto bedding mortars or bonded screeds.

  1. Planing or grinding of ridgesEliminate localised humps using a diamond grinder or concrete planer as soon as the concrete has achieved sufficient strength to prevent aggregate pull-out.
  2. Shot blasting to open poresTreat excessively smooth surfaces by steel shot blasting to recreate the roughness required for the keying of resins or mortars without damaging the upper reinforcement layer.
  3. Contractual noticePursuant to art. 365 CO, the contractor notifies the client of any circumstance compromising the proper execution of the works. Written documentation prevents disputes at the acceptance stage governed by CO.

Frequently asked questions

How do you identify the exact moment to start mechanical power floating?

Power floating begins when the operator's footprint on the fresh concrete sinks by no more than 5 to 8 mm. If the sole sinks deeper, the machine destroys the aggregate skeleton and creates waves. If the concrete takes no imprint at all, the surface mortar has begun to set: surfacing becomes impossible without adding water, a prohibited practice that permanently weakens the wearing layer.

Can bituminous waterproofing be laid directly on power-floated concrete?

No, a simply power-floated finish leaves open pores, aggregate edges, and a roughness incompatible with bonding a bituminous waterproofing sheet. The substrate requires careful mechanical trowelling or fine floating free of protruding asperities. A surface that is too rough risks puncturing the membrane under the load of subsequent insulation layers or preventing continuous coverage of the cold-applied primer.

Why reject surfacing on a slab intended to receive a bonded screed?

Extensive mechanical trowelling brings fines and cement to the top, creating a dense, impermeable laitance that blocks the mechanical keying of the screed. For a bonded finishing work system, the reinforced concrete substrate must retain an open and rough texture, obtained simply by screeding with a vibrating rule or by broom finishing. Concrete that is too closed would force the subsequent trade to perform unplanned heavy shot blasting.

What flatness tolerance applies if the contract remains silent on standard SIA 414?

In the absence of an explicit contractual specification, the normal tolerances of standard SIA 414 prevail for structural work. For a raw as-cast or standard power-floated slab, the permissible deviation under the 2 m straight edge is generally 10 mm. If the finishing work requires a higher precision class, this must imperatively be included in the contract documents prior to casting.

Texts and standards cited

  • norme SIA 414Dimensional tolerances in building construction
  • CO art. 365Materials and ground: the contractor is liable for the good quality of the materials supplied; if the material supplied by the client or the ground designated by the client is found to be defective, or if any other circumstance compromises the regular or punctual execution of the work, the contractor shall immediately inform the client, under penalty of bearing the consequences (para. 3).
  • COAfter delivery, the client inspects the condition of the work as soon as feasible and notifies defects to the contractor; for an immovable work, the client has 60 days to report them, and a shorter contractual period is void (para. 1bis, in force since 1 January 2026); either party may request an examination by experts (para. 2).

In the same section