Skip to content
Website
🧱 CFC 211.1Joints, propping and structural phasingChapter 1 of 10 in the section

Expansion joint: width, full-height continuity and treatment

This chapter details the execution rules for expansion joints in reinforced concrete structures. You will learn how to ensure their absolute continuity over the full height of the building according to the requirements of standard SIA 260, how to keep the design gap free of hard objects, and how to coordinate interfaces to prevent any rigid bridging.

Key takeaways

  • The expansion joint must cut completely through the superstructure without steel continuity or rigid bearing.
  • The unobstructed width must scrupulously comply with the minimum dimension determined by the civil engineer.
  • A single hard bridge cancels the effectiveness of the joint and generates severe structural distress.
  • Building services penetrations and finishing work elements require fully deformable sliding connections.

Ensuring the full continuity of the cut according to standard SIA 260

In a reinforced concrete structure, the expansion joint absorbs reversible and irreversible dimensional variations resulting from thermal gradients, drying shrinkage and creep. According to the design principles of standard SIA 260, structural design must incorporate these imposed deformations in order to prevent excessive internal stresses from developing. The interruption of material must be absolute. All too often, misinterpretation on the construction site leads to stopping the joint above the basement or treating it superficially on intermediate floors, which concentrates shear forces at the remaining rigid connections.

Structural expansion joint
Complete transversal cut separating two blocks of a structure to allow their differential relative movements without inducing parasitic stresses in slabs, walls and columns.

The structural cut must start at the level determined by the structural concept: either right from the top of the raft foundation if the latter absorbs movements through friction on the ground, or at the junction between the rigid basement and the slender superstructure. Once initiated, the separation applies to all load-bearing components: slabs, main beams, shear walls, columns and roof slabs. Two independent structures must coexist without any transverse reinforcement crossing the gap, with the sole exception of shear-transmission dowels specially designed with smooth sliding sleeves and axial expansion boxes.

Failure to comply with the recognised rules of construction exposes project participants to major structural disputes. When execution results in a defect that compromises the integrity of the structure, the engineer and the contractor face the risk of bearing heavy remedial costs. Pursuant to art. 229 CP, any person who intentionally or through negligence infringes the rules of construction during the management or execution of a structure and thereby endangers the life or physical integrity of persons is liable to criminal prosecution. A poorly managed through-crack or the unexpected crushing of a wall under thermal stress constitutes a serious hazard for the building.

Maintaining the calculated clear width and eliminating any risk of bridging

The joint thickness is defined by the engineering design office by applying combinations of thermal and seismic actions. This nominal value corresponds to a completely empty space or one filled with a certified compressible material. Utmost vigilance is required during the pouring of successive slabs and walls: concrete laitance or aggregates seeping behind a formwork panel create indeformable hard bridges. During the summer thermal expansion of the building, these accidental wedges lock the movement, causing the spalling of cover concrete, localised buckling or the shearing of wall corners.

Component behaviour at the structural joint
Building elementProhibited practice (bridging)Compliant solution
Starter barsBars crossing the joint between phasesComplete termination of bars with compliant concrete cover
Shear dowelsReinforcing bars grouted at both endsSmooth dowels with expansion sleeve and lateral box
Edge formworkPoured concrete run-off or laitance residuesTight compressible material and clean joint bottom
Pipes and ductworkRigid penetration grouted into both wallsFlexible expansion compensator sleeves or expansion loops
Finishing profilesMetal joint cover screwed on both sidesUnilateral fixing or sliding profile beneath elastomer
  1. Installation of formwork and separating materialInstall a continuous resilient filler (rigid mineral wool board, closed-cell polyethylene foam) mechanically fixed against the first hardened element, without discontinuities or rigid transverse clips.
  2. Protection against laitance seepageApply a waterproof adhesive tape or a flexible sealing profile along the joint edges prior to concreting the adjacent phase to prevent any cement penetration.
  3. Visual inspection prior to closureInspect the gap over its full height using a torch to check for the complete absence of concrete runs, rubble or reinforcement offcuts.
  4. Installation of suitable joint coversInstall coverings on roofs and trafficable slabs that are capable of absorbing the prescribed three-dimensional movement without locking the concrete edges.

On the construction site, the opening tolerance must be checked as floor levels are erected. Under no circumstances must the residual opening be narrowed by formwork deformations or out-of-plumb deviations during the placement of reinforced concrete.

Crossing systems and shear transfer without locking

When structural or operational requirements prevent the systematic doubling of walls or columns along the expansion joint, the civil engineer specifies shear-transfer dowels. These metal components allow the transfer of vertical loads from one structural block to the other while permitting strictly unhindered axial sliding under thermal and shrinkage effects, in accordance with the requirements of standard SIA 260 regarding the separation of substructures.

The effectiveness of the dowel relies on the sliding of the sleeve embedded in the second concreting phase. An angular misalignment of a few millimetres or a deformation of the casing under concreting pressure creates a mechanical binding effect. The load transfer then turns into a hard point, which blocks the free expansion and contraction of the structure and induces unforeseen tensile stresses in the adjacent slabs.

Typology of load-transfer systems and alignment tolerances
Structural elementMechanical roleRequired degree of freedomCritical installation point
Single dowel with cylindrical sleeveTransfer of pure vertical shearLongitudinal axial sliding (dowel axis)Strict alignment perpendicular to the joint plane; non-deformable support fixing
Dowel with lateral movement boxTransfer of vertical shear and biaxial thermal movementLongitudinal axial sliding and horizontal lateral displacementVerification of transverse clearance prior to formwork closure; initial bar centring
Concrete corbel with sliding bearingSimple support of a slab on an adjacent wall or beamMultidirectional planar sliding on bearing padFlatness of the seating, installation of lateral debonding felt to prevent concrete-to-concrete friction
Suspended edge angle ironEdge protection under heavy traffic (car parks, logistics)Mechanical edge retention without interconnection between lipsAnchor bolts cast on one side only or separated by a deformable profile

Waterproofing treatment, thermal insulation and edge closure

A structural expansion joint cannot remain wide open. It must receive flexible systems ensuring resistance to groundwater or water ingress, continuity of fire compartmentation and absence of thermal bridges, without ever introducing stiffness into the empty gap defined by the engineer.

  1. Installation of the elastomeric waterstopFor underground slabs or flat roofs, install a flexible waterstop embedded in the concrete or bonded across the joint. The membrane must include a central hollow bulb positioned exactly on the centreline of the cut, in order to absorb opening cycles without its flanges debonding.
  2. Compressible and non-expansive fillingFill the void with a highly deformable material such as mineral wool or very low-density expanded polystyrene (15 kg/m³). Dry mortar, residual levelling concrete or rigid polyurethane foam must be strictly prohibited, as they transmit compressive stresses between elements.
  3. Installation of waterproofing bridging or finishing profilesFasten joint covers or floor expansion profiles to only one of the joint edges, or use proprietary systems with debonded fixings mounted on sliding tracks. Any through-hole fastening that ties both walls together eliminates the intended movement.
  4. Certified fire protectionInsert a rock-fibre firestop cord or mattress installed under compression between the reinforced concrete edges, sized to maintain the required fire resistance rating even at maximum structural opening.

On roofs and buried retaining walls, connecting to applied waterproofing systems requires a continuous expansion bellow. Installing a continuous metal sheet screwed across both concrete blocks represents a severe non-conformity, causing instant pull-out of fasteners or tearing of the waterproofing under seasonal movements.

Management of joint non-conformities and resolving site blockages

On a structural work construction site, an expansion joint obstructed by hardened laitance runs, misaligned reinforcement or makeshift patch repairs instantly loses its kinematic function. As soon as two distinct structural blocks are locked together, thermal and shrinkage stresses accumulate at this hard point, triggering uncontrolled diagonal cracking in walls or edge spalling on adjacent slabs.

  1. Identification and mapping of the restraintLocate the bridging point visually using a spotlight or plumb line between the pours. Strictly prohibit any attempt to conceal it with levelling mortar.
  2. Formal notification to site managementNotify the civil engineer in writing prior to any heavy remediation. According to art. 365 CO, if any circumstance arises that compromises the proper execution of the work, the contractor must inform the principal.
  3. Mechanical clearance without damaging the joint edgesRemove parasitic concrete by diamond sawing or light chipping with an electric breaker. Thermal cutting tools or very high-pressure water lances may be used, provided the dowel steel components are protected.
  4. Void verification and acceptancePass a rigid template calibrated to the drawing dimension down the entire height of the shear wall or slab to prove unrestricted freedom of movement.

If a reinforcing bar crosses the gap due to an installation error, cutting it with a cutting torch or angle grinder requires clearance from the structural engineer, to ensure that no parasitic load transfer imbalances the adjacent support. In the event of overall formwork deviation reducing the clear width below the project value, the application of standard SIA 260 requires a recalculation of the kinematics of the boundary joints before authorising any grinding or reprofiling of the recess.

Frequently asked questions

How can concrete that has seeped into the bottom of an inaccessible joint be cleaned out?

If laitance or run-off obstructs the space between two walls cast against the ground, manual cleaning with a chisel is impossible. The crew carries out precise vertical core drilling at the plug or uses targeted hydrodemolition with a guided nozzle. The intervention must restore the theoretical gap specified by the engineer's drawings over the full height of the cut, without damaging the cover reinforcement.

Can the concrete edges be ground down if the joint width is insufficient after pouring?

Planing or vertical sawing of one of the faces is acceptable only after approval by the civil engineer. The engineer first verifies that cutting back the concrete does not encroach on the minimum concrete cover prescribed by standard SIA 260 for the exposure class of the wall. If reinforcement is exposed, certified anti-corrosion treatment and specific reprofiling become mandatory.

What should be done if a shear-transfer dowel does not slide smoothly during installation?

The dowel sleeve must be perfectly aligned with the intended sliding axis. If the sleeve is crushed, twisted or filled with cement laitance during the first concreting stage, the dowel forms a hard point and locks expansion. The sleeve must be completely cleared or the damaged assembly removed to grout in a new sleeve in accordance with the original specifications.

Can a sealing profile be used to support the joint formwork stop-end?

No. The sealing strip or waterstop is intended solely to ensure the watertightness of the cut. Using it as a concrete stop-end or compressing it with clamping boards risks puncturing its deformable bulbs or misaligning its anchoring ribs. Edge formwork must consist of independent stop-end panels incorporating dedicated watertight pockets for the profile ribs.

Texts and standards cited

  • norme SIA 260Basis of structural design
  • CO art. 365materials and ground: the contractor is responsible for the good quality of the materials he supplies; if the materials supplied by the employer or the ground designated by him are found to be defective, or if any other circumstance compromises the proper or timely execution of the work, he shall immediately inform the employer thereof, under penalty of bearing the consequences (para. 3)

In the same section