Skip to content
Website
🧱 CFC 211.1Formwork: wall forms, form liners and surface finish qualityChapter 4 of 10 in the section

Shuttering panel stability: propping, ballasting and wind load

A shuttering panel placed without its counterpart acts as a significant wind sail on the slab. This chapter details the dimensioning of stability props, anchorage rules in first-phase concrete, and strict criteria for stopping handling and concreting during foehn or bise gusts.

Key takeaways

  • An isolated panel behaves like a sail under aerodynamic positive and negative pressures.
  • OTConst art. 17 requires measures to protect workstations against the collapse of elements.
  • Push-pull props and their baseplates must be secured before unhooking the crane.
  • Wind mandates stopping lifting and securing panels in accordance with the manufacturer's manual.

Wind forces and anchorage rules for stability props

As soon as a vertical formwork panel leaves the storage stack to be erected on the slab, it acts as a sail. The solid surface of a standard-height panel experiences a direct horizontal force under wind pressure, as well as suction on its rear face. Without a rigid mechanical connection, overturning is instantaneous. In accordance with OTConst art. 17, at workstations and passageways, measures must be taken to ensure that workers are not endangered by the collapse of building components.

Triangulation components and mechanical stresses
Mechanical componentPrimary functionOperating mode
Upper push-pull propPlumb maintenance and wind load resistanceAlternating tension and compression
Foot prop (or lower shoe)Locking the panel base against slidingHorizontal shear
Anchor bolt / screw anchorConnection to the first-phase concrete substrateVertical pull-out and shear
Baseplate pinConnection between prop head and steel frameworkDouble shear

Propping a shuttering panel serves a dual purpose: millimetre-precise plumb adjustment and temporary climatic load resistance. A single prop per panel is prohibited. Stability is achieved using pairs of screw-adjustable telescopic props, arranged symmetrically to prevent any rotation around the vertical axis. Impact anchors or concrete screws used in the slab must have a technical datasheet confirming their pull-out resistance in green concrete, often aged less than forty-eight hours during formwork rotation.

Weather monitoring and work stoppage instructions

Local wind channels, such as the foehn in Alpine valleys or the bise across the Plateau, cause violent aerodynamic accelerations. Formwork stability against wind does not rely on visual estimation: it demands continuous monitoring of gust speeds at the workstation level and at the top of the panel.

  1. Measurement and warningConsult the crane anemometer and use a handheld anemometer on the top formwork platform during local weather warnings.
  2. Halting crane operationsStop handling large panels as soon as the limit speed specified by the crane or formwork manufacturer is reached, generally around 50 km/h.
  3. Reinforcing stabilityEnsure face-to-face panel gangs are fully closed, or install additional props if a panel remains isolated overnight.
  4. Evacuating the fall zoneCordon off and prohibit access downwind of vertical elements that are not permanently braced by poured concrete.

Work stoppage is an operational decision resting with construction site management. When the wind picks up, handling slung panels becomes uncontrollable and poses a fatal crushing risk to formworkers on the ground. The formwork manufacturer's technical manual defines the maximum permissible wind speed for a single panel braced with standard props. Beyond this temporary design threshold, emergency props or ground tie-backs must be deployed immediately.

Aerodynamic behaviour of an isolated panel and overturning kinematics

As long as a gang of panels is not closed by its opposite side and through tie-rods, each standing steel panel acts as a rigid sail exposed to air currents. Wind loads on the shuttering panel generate dynamic pressure on the formwork face or ribbed backing structure, inducing an immediate overturning moment at the base. Without a rigid mechanical connection capable of alternating between tension and compression, the assembly pivots instantly around its lower resting edge.

OTConst art. 17 states that at workstations and passageways, measures must be taken to ensure that workers are not endangered by the collapse of building components or falling objects and materials. On a structural work construction site, the accidental overturning of a multi-tonne formwork panel presents a severe crushing hazard. The self-supporting stability of the panel depends exclusively on the diagonal propping system and the reliability of its anchorages into the raft foundation or cured concrete slab.

Dynamic wind load transfer on a vertical formwork element
Wind flow directionLoad on the formwork faceAdjustment prop behaviourLoad transferred to the ground anchorage
Wind hitting the formwork face (tailwind)Direct positive pressure pushing towards the proppingAxial compression in the prop tubeDiagonal thrust and bearing compression on the slab
Wind hitting the ribbed back (uplift wind)Suction and negative pressure pulling the panel forwardPure tension in the propping systemDirect vertical pull-out on the anchor or shoe
Glancing wind parallel to the wallEnd turbulence and lateral instabilityCombined torsional and shear loadsTransverse sliding and fastener shear

The uplift phenomenon under reverse frontal wind requires each fixing point to be calculated for tension resistance without slip. The use of mandatory stability props designed with double-screw adjustment allows plumb alignment to be locked while providing the mechanical bracing needed to withstand downbursts and vortices generated by adjacent buildings.

Ground anchoring systems, ballasting and operational weather management

Anchoring push-pull prop baseplates requires strict attention to the mechanical strength of the supporting substrate. On green concrete, mechanical expansion anchors or concrete screws must be installed strictly respecting the embedment depth and edge distances specified in the manufacturers' technical datasheets. An anchor drilled into concrete that has not achieved sufficient strength will pull out under the first suction loads caused by a gust.

  1. Installing and tensioning heavy proppingAttach double-screw props to the panel while it is still secured to the crane hook. Adjust the inclination angle recommended in the technical manual before lowering the panel onto its setting blocks.
  2. Mechanical anchorage of the baseplateDrill into the raft foundation or slab using the recommended tool diameter, blow out drilling dust, and drive the concrete screw or anchor bolt to the required tightening torque.
  3. Releasing crane slingsOnly release lifting slings once the safety pins on the props are locked and the baseplate's slip resistance has been fully verified.
  4. Enforcing the high-wind shutdown procedureAs soon as the crane or handheld anemometer indicates that the equipment's operating thresholds are being approached, immediately suspend formwork handling and lock the panels using complete closures or temporary raking shores.

The high-wind shutdown procedure is the ultimate safety barrier on the construction site. When gusts exceed the limit values defined by the formwork manufacturer's instruction manual or Suva crane work guidelines, continuing fine plumb adjustments becomes hazardous. Isolated, unbraced elements must be made safe, either by installing additional safety props or by laying them flat on timber dunnage outside traffic routes immediately.

Action during weather warnings and emergency securing of panel gangs

As soon as wind gusts approaching the operating limits of the crane or formwork system are announced, the site foreman orders the suspension of overhead lifting. An isolated, unbraced panel acts like a sail under aerodynamic negative pressures. According to OTConst art. 17, at workstations and passageways, measures must be taken to ensure that workers are not endangered by the collapse of building components or falling objects and materials. Mandatory stability props absorb the push and pull forces generated by turbulence. If a vertical panel has not yet received its facing counterpart, it relies entirely on its anchorage to the raft foundation or slab.

In the event of unexpected ground failure, slack in an anchor bolt, or a sudden strengthening of the bise, the crew immediately applies the high-wind shutdown procedure. Leaving formwork suspended from a crane hook in an attempt to stabilise it is strictly prohibited: wind resistance on the panel transfers uncontrollable dynamic forces to the crane boom and increases the risk of overturning.

  1. Area lockout and evacuationStop lifting, land the panel on the ground, or fold it onto its storage frame if the operation is already under way. Evacuate personnel downwind of the equipment and cordon off peripheral access with rigid physical barriers.
  2. Checking shoring and fixingsCheck the tightness of anchor studs on the hardened concrete. If the wind increases before the formwork is closed, double the push-pull props or strap the panel to heavy starter bars that have been verified in advance.
  3. Immediate pairing of formwork panelsPrioritise closing face-to-face panels with tie-rods and wing nuts to form a self-stable box structure capable of resisting aerodynamic forces without relying solely on anchor baseplates.

Frequently asked questions

At what precise wind threshold must vertical formwork lifting be stopped?

The high-wind shutdown instruction applies as soon as the wind speed reaches the limit set by the crane or formwork manufacturer's manual, typically around 50 km/h for large panels. Wind load on the panel generates violent swinging movements. The crane operator and site foreman decide to halt operations before guidance from the ground is lost.

Why are stability props mandatory even in calm wind conditions?

Mandatory stability props prevent accidental overturning caused by an unexpected thermal gust, plant impact, or ladder placement. They absorb both tensile and compressive stresses. OTConst art. 17 requires workers to be protected against the collapse of building components. An unpropped panel has a high centre of gravity and precarious stability on its levelling feet.

What should be done if the concrete slab lacks the required strength for prop anchorage?

On green concrete where strength is insufficient to guarantee expansion anchor or concrete screw performance, direct anchoring is ruled out. Certified precast concrete ballast blocks dimensioned against sliding and overturning must be used, or through-bolts must be installed across the slab into an underlying structural element that has cured in accordance with good building practice.

How should an isolated panel left standing at the end of the shift be secured?

A panel must never remain isolated if overnight weather conditions are uncertain. The team doubles the push-pull propping anchored to the slab or secures the panel to the opposing panel using through tie-rods to close the cell. In the event of a storm warning, the recommended method is to lay the formwork flat on timber dunnage or in its storage racks.

Texts and standards cited

  • OTConst art. 17protection against the collapse of building components or falling objects and materials: at workstations and passageways, measures must be taken so that workers are not endangered

In the same section