Skip to content
Website
🧱 CFC 211.1Pathologies of reinforced concrete, diagnosis and strengtheningChapter 2 of 10 in the section

Reinforcement corrosion: from rust stains to cover spalling

On a reinforced concrete façade, a simple surface discolouration often foreshadows deep structural distress. This chapter details the methodical reading of degradation stages, the assessment of residual steel cross-sectional loss, and the critical transition between an aesthetic defect and a risk to structural safety according to Swiss condition assessment criteria.

Key takeaways

  • Oxide run-offs precede longitudinal cracking prior to the complete detachment of the concrete cover.
  • Corrosion potential measurement locates anodic activity before any visible signs appear on the surface.
  • The civil engineer recalculates load-bearing capacity as soon as the steel cross-section decreases significantly.
  • Standard SIA 269 governs condition assessment and the evaluation of structural safety.

Recognising the four visible stages of degradation on concrete surfaces

A methodical visual inspection of a reinforced concrete façade allows the history of the corrosive attack to be reconstructed without immediately resorting to heavy destructive testing. Rust formation is accompanied by volumetric expansion that increases the initial volume of steel by a factor of two to six. This expansion generates internal tensile stresses exceeding the tensile strength of the concrete cover, inexorably leading to the failure of the protective layer.

Degradation stages of a concrete surface subjected to reinforcement corrosion
StageVisual manifestationCondition of steel-concrete interfaceAction required on construction site
Stage 1: IncubationSound surface or transverse shrinkage microcracks without discolouration.Carbonation front or chlorides progressing towards the reinforcement, passive film intact.Non-destructive cover check and potential mapping.
Stage 2: Staining and run-offsBrown haloes or rust seeping through porosity along the rebars.Local breakdown of passivation, onset of active oxidation without significant loss of cross-section.Spot chiselling inspection and measurement of carbonation depth.
Stage 3: Parallel crackingStraight cracks of 0.2 to 1.5 mm tracking the reinforcement layout exactly.Active expansion pressure, concrete debonding initiated, extensive underlying corrosion.Preventive chipping away of loose concrete and geometric recording of crack widths.
Stage 4: Spalling / DelaminationDetachment of entire concrete sections, reinforcement completely exposed and delaminated.Total loss of bond on the exposed side, deep pitting or reduction in diameter.Immediate safety securing against falling objects and recalculation of load-bearing cross-section.

As soon as continuous cracks parallel to the bars appear, the phenomenon accelerates. The opening of the concrete allows direct ingress of water, oxygen, and carbon dioxide, completely eliminating any protection provided by the residual cover. The dull, hollow sound produced when tapping with a geological hammer reveals internal delaminations even before they fall away.

Quantifying cross-sectional loss and assessing risk under standard SIA 269

The shift from an aesthetic maintenance issue to a verified structural failure depends on the structural function of the corroded steel. A loss of cross-section on a shear stirrup or on the main reinforcement of a cantilever balcony directly alters the ultimate limit state of the structure. The engineer must quantify the remaining sound material using a vernier caliper after careful breaking out and mechanical wire-brushing of oxidation products.

Corrosion potential measurement
Non-destructive electrochemical condition assessment method consisting of measuring the potential difference between the reinforcement and a reference electrode placed on the surface of the damp concrete, allowing areas of actively corroding steel to be identified prior to the emergence of visible defects.

Potential mapping uses a reference electrode (most commonly copper/saturated copper sulphate). Values more negative than a critical threshold in the region of -350 mV indicate a probability exceeding 90 % of active corrosion. This technique is indispensable for delineating the repair areas beyond visibly spalled zones alone.

Structural intervention thresholds for corroded reinforcement
Measured cross-section loss (ΔA)Observed mechanical impactClassification of defectEngineering measure according to SIA 269
Less than 5 %Preservation of nominal load-bearing capacity, bond maintained.Predominantly aesthetic defect and compromised durability.Monitoring of the structure and rescheduling of maintenance cycles.
Between 5 % and 15 %Onset of stress redistribution, reduction in plastic safety reserve.Moderate structural damage requiring analytical verification.Recalculation of critical sections according to standard SIA 269 and verification of bond.
Greater than 15 % or pittingSharp drop in shear or flexural strength, risk of brittle failure.Non-compliance of structural safety of the load-bearing element.Immediate preventive propping, addition of reinforcing bars or bonded carbon plates.

The Swiss series of standards for existing structures, particularly standard SIA 269, prescribes a rigorous methodology in the event of pathology: condition assessment, evaluation of structural safety using actual material dimensions and properties, followed by a substantiated decision on preservation, repair, or strengthening. Furthermore, art. 365 CO stipulates that the contractor must immediately notify any circumstance that compromises the proper execution of the works.

Corrosion potential measurement and non-destructive condition assessment on façades

The absence of cracking or spalling on a concrete surface does not guarantee the integrity of the underlying reinforcement. In situations exposed to salt spray, de-icing salts, or areas subjected to carbonation without continuous saturating moisture, corrosion can progress without immediately creating sufficient expansion to spall the concrete. To establish a reliable diagnosis before making any structural intervention decision according to standard SIA 269, electrochemical potential mapping is the benchmark non-destructive method.

  1. Locating reinforcement and localized exposureLocate the reinforcement layout using an electromagnetic cover meter to identify main load-bearing bars and stirrups. Execute a targeted breakout with a pneumatic or manual chisel to expose a sound bar, wire-brush the metal to a bright finish, and attach a direct electrical connection using a locking clamp or contact screw.
  2. Verification of electrical continuity within the reinforcement cageCheck galvanic continuity between adjacent bars using a standard ohmmeter. A measured resistance of less than 1 ohm confirms that the entire mesh or reinforcement cage forms a continuous circuit, permitting site-wide condition assessment from a single contact terminal.
  3. Pre-wetting of the substrate and surface scanningDampen the concrete surface with clean, non-demineralised water to ensure the closure of the electrolytic circuit through the concrete pores. Move the copper sulphate reference electrode (CSE) or silver/silver chloride electrode across a regular pre-marked grid, typically spaced between 15 and 25 cm apart.
  4. Mapping and interpretation of gradientsRecord the measured potential values in millivolts on an elevation drawing to plot equipotential contours. More than absolute values, it is areas with steep potential gradients that identify active macrocells and locate anodic zones where the metal is actively dissolving beneath seemingly sound concrete.
Interpretation of CSE electrode potentials according to corrosion activity status
Measured potential (mV relative to CSE)Probability of corrosive activityPhysical condition of reinforcementAction required on the structure
More positive than -200 mVLess than 10 %Stable passivation, protective oxide layer intactPeriodic monitoring within the maintenance plan
Between -200 mV and -350 mVUncertain (transition zone)Possible local depassivation, onset of pittingTargeted destructive breakouts for residual measurement
More negative than -350 mVGreater than 90 %Active corrosion, ongoing loss of steel cross-sectionVerification of structural safety according to standard SIA 269

Technical decision-making: from simple remediation to structural strengthening

Crossing the threshold between an aesthetic defect and a structural risk depends directly on the static function of the affected reinforcement and its loss of effective cross-section. An isolated spall on a balcony corner exposes secondary reinforcement without compromising overall equilibrium. Conversely, cover delamination along the main rebar of a beam, a cantilever, or a shear wall simultaneously impairs tensile load-bearing capacity and steel-concrete bond due to the destruction of the end compression strut.

  • Geometric cross-sectional loss of less than 10 % on main bars without deterioration of stirrups: the structure retains its load-bearing margin; profiling restoration and reinstatement of alkaline protection are sufficient.
  • Cross-sectional loss between 10 % and 20 %: mandatory recalculation of load-bearing capacity according to standard SIA 269, taking into account the actual ultimate limit state (ULS) of the element concerned.
  • Cross-sectional loss greater than 20 % or rupture of confinement stirrups: major loss of anchorage requiring immediate installation of safety props and strengthening using bonded composite plates or mechanically anchored supplementary rebars.
  • Chloride-induced pitting corrosion: localised reduction that cannot be accurately measured with calipers without complete breakout, requiring an increased safety factor during static recalculation.

On-site intervention requires strict safety coordination. Technicians and masons performing concrete chipping and reinforcement investigations must apply the measures laid down in the construction work ordinance. In particular, according to art. 17 OTConst, at workplaces and passageways, measures must be taken to ensure that workers are not endangered by the collapse of building elements or falling objects and materials. The areas beneath chipped elements must be fully cordoned off and protected by catch platforms or containment nets until consolidation work is complete.

Passivation of reinforcement
Protective chemical state imparted to steel by the highly alkaline pH (between 12.5 and 13.5) of the pore solution in sound concrete, forming a microscopic oxide film that prevents the iron from reacting with oxygen and moisture.

Crisis management on deteriorated façades: securing, duty to notify, and structural arbitration

On a refurbishment construction site or during a visual inspection of an existing structure, the discovery of generalised spalling with corroded reinforcement requires an immediate departure from the normal routine. As soon as cover fragments threaten to detach above traffic routes, building entrances, or workstations, the absolute priority remains the physical safety of persons. At workplaces and passageways, measures must be taken to ensure that workers are not endangered, in accordance with art. 17 OTConst.

  • Immediately chip away areas sounding hollow beneath the reinforcement layer using a chipping hammer or pointed chisel.
  • Install debris netting without delay beneath slab edges, parapets, and unstable balcony soffits.
  • Set up substantial ground-level barriers to exclude all pedestrian traffic directly beneath the façade overhang.
  • Record the precise condition of the bars through an agreed joint photographic survey prior to any demolition work.

As soon as corroded bars display obvious cross-sectional loss—typically beyond 15 to 20 % of nominal diameter on main edge rebars or shear links—the boundary between routine maintenance and partial collapse risk is crossed. Pursuant to art. 365 CO, if any circumstance arises that compromises the regular or timely execution of the work, the contractor must notify the client. The notice of defects must expressly state the compromise to load-bearing capacity and formally call for the intervention of the civil engineer responsible for monitoring the structure.

The civil engineer applies the framework of standard SIA 269 to recalculate the permissible residual section based on actual service stresses. If this recalculation confirms a structural deficit, project management must arbitrate between adding weldable rebar with chemically anchored dowels, installing bonded carbon-fibre plates, or performing complete hydraulic jacking with replacement of the structural element.

Frequently asked questions

How do you distinguish a simple tie wire stain from corroded main load-bearing rebar?

An isolated spot without linear cracking often originates from a tie wire placed too close to the formwork face. To verify, chip locally using a flat chisel: if the rust remains confined to a wire thinner than two millimetres without debonding of the adjacent concrete, there is no structural risk. Conversely, a continuous rust trail running along the main reinforcement indicates carbonation reaching a load-bearing bar.

At what percentage of steel section loss must a civil engineer intervene?

As soon as the cross-sectional loss measured with a caliper exceeds 10 to 15 % on a main bar or shear stirrup, recalculation according to standard SIA 269 becomes essential. In the presence of localised and deep chloride-induced pitting corrosion, this threshold drops immediately: localised thinning embrittles steel under tensile load and demands static structural verification without waiting for complete cover spalling.

What is the purpose of measuring corrosion potential if the cover has not spalled?

Electrochemical potential mapping using a copper-copper sulphate electrode detects active corrosive activity before cracks appear on the surface. Passivated rebars display positive or weakly negative potentials, whereas depassivated zones typically drop below minus three hundred and fifty millivolts. This non-destructive measurement accurately delimits areas of corroded reinforcement beneath concrete that still looks completely sound.

Can a cracked lintel be reprofiled without fully exposing the steel around its entire perimeter?

No. Any repair mortar applied to reinforcement whose back face remains embedded in carbonated concrete forms a galvanic macrocell that accelerates concealed corrosion. To restore bond and ensure the durability of the structure, it is mandatory to break out the concrete behind the bar to a minimum depth of 15 to 20 millimetres, thereby completely exposing the metal circumference prior to the planned structural strengthening.

Texts and standards cited

  • SIA 269Bases for the maintenance of existing load-bearing structures, condition assessment and structural safety
  • OTConst art. 17Protection against the collapse of structural elements or falling objects and materials: at workplaces and passageways, measures must be taken so that workers are not endangered.
  • CO art. 365Materials and site conditions: the contractor is liable for the sound quality of the materials supplied; if the materials supplied by the client or the site designated by the client are found to be defective, or if any other circumstance arises that compromises the regular or timely execution of the work, the contractor shall immediately inform the client, under penalty of bearing the consequences thereof (para. 3).

In the same section