Skip to content
Website
🧱 CFC 211.1Formwork: wall forms, form liners and surface finish qualityChapter 7 of 10 in the section

Traditional timber formwork: curved shapes, angles, and custom profiles

Faced with the geometric limits of metal panel formwork, the traditional formworker shapes structures with unusual radii or variable curvature. You will learn how to set out full-scale lines, cut curved ribs, gauge the formwork skin to the radius, stiffen the structure against hydrostatic pressure, and keep within tolerances without falling victim to timber deformation.

Key takeaways

  • Full-scale ground setting out ensures accurate radii and precise cutting of ribs.
  • Plywood thickness and grain direction dictate the allowable limit radius without fibre failure.
  • Stiffening with curved walers and tie rods resists the hydrostatic pressures of fresh concrete.
  • Custom form pieces require strict opening control to prevent creep under load.

Full-scale setting out, templates, and bending of formwork skins

Industrial formwork panels reach their limits as soon as the project dictates a radius tighter than the capacity of adjustable curved panels, a variable curvature (basket-handle arch, clothoid), or a complex angular junction. For these non-standard geometries, traditional timber formwork comes into its own. Work begins with a full-scale layout struck directly onto a chipboard platform or onto the raft slab. Using a steel chalk line, a straight edge, and a marking gauge, the neutral axis and both faces of the wall are marked out. This layout is used to fabricate templates from 21 or 27 millimetre wood-based panels, which will then guide the cutting of horizontal ribs or load-bearing curved frames.

Curved frame
Timber framework cut to the theoretical radius of curvature, assembled by flitch plating or nailing, serving as direct support for battens or thin formwork panels.

The selection of the formwork skin depends directly on the minimum radius of curvature specified in the formwork drawings. Standard 15-millimetre birch plywood cannot be bent below a radius of 2.5 to 3 metres without suffering delamination or surface cracking. For sharper curves, using thinner panels (6, 8, or 9 millimetre panels laid in cross-laminated layers) becomes essential. The grain direction of the panel also governs its flexibility: bending plywood parallel to the grain of its face veneers requires less effort but exposes the surfaces to blistering during vibration.

Indicative dry-bending radii according to plywood thickness
Nominal thicknessBending directionIndicative minimum radiusTypical use
6 mmPerpendicular to grain0.80 m to 1.00 mDouble layered skins for tight columns
9 mmPerpendicular to grain1.40 m to 1.60 mCurved walls for spiral staircases
15 mmPerpendicular to grain2.80 m to 3.20 mLarge-radius curved retaining walls
21 mmPerpendicular to grain5.00 m and aboveLarge basins and car park ramps

For radii under 80 centimetres, planed softwood matchboarding with chamfered tongue and groove replaces flat sheeting, unless the plywood is steam-bent using hot water. Mechanically fixing the skin onto the ribs must proceed from the centre of the template towards the ends to eliminate crowning and residual tension in the timber.

Stiffening, load transfer, and dimensional control of custom form pieces

The kinematics of forces in curved formwork differ fundamentally from those in straight panel formwork. Liquid concrete pressure generates tangential thrusts that tend to burst the arch open or displace the centreline. The primary framework cannot rely on standard straight steel sections without adaptation: curved ribs cut from glued-laminated timber or heavy-section planks (75 x 150 millimetres minimum) receive vertical stiffeners spaced according to the planned rate of placing.

  1. Setting out and wedging the bottom ribFix the curved sole plates to the ground with hammer-set anchor plugs following the layout, then position kickers to prevent any lateral sliding.
  2. Assembling the frame cageErect the vertical frames and tie the curved walers together at regular intervals, typically spaced closer together over the first metre of height.
  3. Drilling and fitting tie rodsDrill through the skin perpendicular to the tangent of the curve to prevent articulated wing nuts and bearing plates from bending under biaxial loads.
  4. Bracing and triangulationInstall push-pull props directed towards the centres of the radius and diagonally brace the structure to prevent racking under asymmetrical pressure.

Reusing these bespoke structures remains very limited. Subject to permanent deformation caused by lateral pressure and concrete moisture cycles, the timber works: the framework frames suffer creep and the thin skins absorb mix water, making a second pour dimensionally risky without re-truing. A complex element allows for only two to three pour phases at most before complete refurbishment of the contact skin.

Erecting such a structure requires constant vigilance regarding assembly safety. The employer applies art. 3 OPA to provide working installations that ensure personnel protection, notably adapting suspended pouring platforms to non-linear geometries. Furthermore, in accordance with art. 77 OTConst, falsework and supporting structures must be dimensioned to withstand the foreseeable loads and forces on the construction site.

Tolerance control and stabilization of custom form pieces

Constructing reinforced concrete elements with complex geometry, such as curved walls or polygonal drop beams, requires assembly precision that hand-set modular systems cannot achieve. While standardized metal panels impose a rigid tie grid, traditional timber construction places all stiffness on the formwork carpentry: glued flitch plates, template-cut frames, and distribution walers. The slightest inaccuracy in cutting flitches or inadequate wedging of tie rods leads to displacement under the hydrostatic pressure of fresh concrete, irreversibly distorting the intended curvature.

To meet execution dimensions, allowable deflection of the formwork skin between vertical stiffeners (studs or secondary beams) is restrained by reduced spacing. Unlike straight walls where stiffener centres commonly reach 30 to 50 cm, a curved surface with a tight radius often requires a spacing of 15 to 20 cm to prevent faceting of thin plywood. Fixing anchor ties cannot be done perpendicular to an ordinary flat face: it requires bevelled hardwood wedges or suitable swivel plates, otherwise the rods may be subjected to shear or the backing ribs may experience localized crush failure.

During alignment on the sole plate, lateral thrust forces are resisted via push-pull props anchored to the ground or to a concrete kicker. Art. 77 OTConst requires falsework and sheeting to withstand foreseeable loads and forces, be built to recognized technical rules, and be dimensioned taking additional loads into account. On single-sided curved formwork, uplift force at the foot and overturning must be resisted by steel walers tied to the timber frames to prevent any lifting as the concrete rises.

Material wear, limited reuse, and end-of-phase recovery

Traditional timber formwork for complex shapes offers significantly lower durability than industrial metal systems. Mechanical stresses exerted on thin skins during bending create micro-cracks in the outer veneers of the plywood. These tears promote the absorption of water and cement paste, causing localized wood swelling, edge delamination, and loss of tightness at joint lines.

Behaviour of formwork materials on custom form pieces by number of reuses
Formwork componentStructural roleAverage number of reusesLimiting factor for durability
6-9 mm bendable plywoodFormwork face in contact with concrete1 to 2 timesVeneer cracking, blistering under moisture, tearing on stripping
Bevel-cut 21-27 mm 3-ply panelsCurved frames and shaped ribs3 to 5 timesPermanent deformation, splitting around repeated screw zones
Glued-laminated walers and stiffenersFramework resisting anchor tie loads6 to 10 timesPunching failure from bearing plates, hole ovalisation
Close-jointed trapezoidal fir battensSoffits or drop beams with very tight radius1 single useImpregnation with cement paste, inability to re-profile

Each striking operation demands special precautions to protect the ribs. Using stripping levers or crowbars directly against curved edges destroys machined profiles. Pressure relief panels and release wedges should be incorporated into the design of the timber structure from the start. As soon as geometric tolerances are no longer guaranteed or edges exhibit spalls exceeding 2 mm, components must be downgraded to non-exposed areas or scrapped.

Art. 365 CO reiterates the contractor's liability for the good quality of materials supplied. On a curved structure requiring a high-quality finish, using timber that has already undergone plastic deformation exposes the contractor to rejection of the works for non-compliance with execution geometries. Factoring depreciation costs into a very short reuse cycle is thus the linchpin of profitability for custom-shaped formwork.

Managing dimensional deviations and failures in curved formwork

On curved structures and non-standard custom shapes, the slightest lack of stiffness translates into visible deformation under the pressure of fresh concrete. When a rib fails, a template deflects, or grout leaks at the joint between curved panels, action must be immediate to stop pouring before setting occurs and prevent the structure from drifting out of tolerance.

  1. Halting the pour and emergency stabilizationHalt the skip or concrete pump as soon as abnormal deflection is observed. Measure the warp using a checking template or a plumb line. If the stiffening is bursting open, install inclined emergency rakers anchored to the slab below or strap the formwork box with temporary threaded through-ties.
  2. Cleaning out and re-setting the layoutIf the deformation exceeds permissible execution tolerances, remove the unhardened fresh concrete by hydrodemolition or manual scraping before it sets. Strip the damaged plywood skin, rebuild the skeleton of curved ribs on the ground layout, and replace any split stiffeners.
  3. Formal notification to site managementNotify without delay of any observed geometric defect or inability to meet the engineer's drawing dimensions due to reinforcement clashes. Art. 365 CO al. 3 requires the contractor to inform the employer if any circumstance compromises the proper or timely execution of the works.

If geometric damage is found after striking, the site foreman records the actual dimensions using a topographical survey. No thick patching mortars or structural scabbing may be undertaken without the written approval of the civil engineer responsible for the structural design of the civil engineering work or building.

Frequently asked questions

How can out-of-round defects on a curved wall be corrected after striking?

If the actual radius deviates from the layout beyond contractual tolerances, the civil engineer must evaluate the impact on reinforcement cover and structural capacity. In the event of excess thickness, mechanical planing or bush hammering may be permitted. For hollow areas, applying a structural repair mortar requires surface preparation by grit blasting and the prior approval of site management.

What should be done if thin plywood snaps during bending over a template?

Breakage indicates a radius of curvature that is too tight for the chosen thickness or an unsuitable grain direction. Switch to a thinner multi-ply panel installed in two cross-laminated layers, for example two 8 mm sheets instead of one 15 mm sheet. Controlled wetting of the outer face during bending also softens the wood fibres before mechanical fastening to the walers.

How should a form joint bursting open between curved panels during pouring be dealt with?

Pouring must be stopped immediately to reduce the hydrostatic head. Fit a rigid cover strip from the outside, nailed or screwed to the stiffeners, and seal the opening with fast-setting expanding foam or a compatible sealant. Then reduce the rate of concrete rise to limit lateral pressure on the weakened area when resuming the pour.

Can bespoke timber formwork deformed during a first pour cycle be reused?

Reusing a curved custom form piece requires a full check of the load-bearing skeleton against the ground layout. If the timber ribs have acquired residual deflection under load or swelling from moisture, they must be trued up or doubled. Damaged or delaminated formwork skin must be systematically replaced to ensure tightness and accurate geometry for the second phase.

Texts and standards cited

  • COmaterials and ground: the contractor is liable for the good quality of materials supplied; if materials supplied by the employer or the ground designated by the employer are found to be defective, or if any other circumstance compromises the proper or timely execution of the works, the contractor must immediately notify the employer, or bear the consequences (al. 3)
  • OTConstprotection against the collapse of building elements or falling objects and materials: at workstations and access routes, measures must be taken to ensure workers are not endangered

In the same section