Key takeaways
- Raking light accentuates micro-relief without constituting a contractual or standards-based defect.
- The visual inspection of a surface is carried out under standardised diffuse lighting in accordance with SIA 242.
- A surface exposed to glazed bays absolutely requires a Q4 finish to be specified in the contract.
- Particular aesthetic requirements and the extra costs of full-surface skim coating must be stated explicitly in your initial offer.
Raking light: distinguishing an optical effect from a workmanship defect
The appearance of pronounced shadows on a plasterboard facing after the final light fittings are installed is one of the most frequent disputes on construction sites. When a recessed spotlight, a full-height glazed bay or an LED strip integrated at the ceiling edge casts a beam almost parallel to the wall, the slightest variation in thickness at the jointing produces a strongly amplified cast shadow. For the client or the painter working afterwards, these visual marks are often wrongly attributed to poor workmanship by the drywall contractor. Yet a wall that strictly complies with dimensional tolerances can look poor under oblique light.
- Raking light
- A light beam striking a facing at a very acute angle, generally less than fifteen degrees to the plane of the partition. This tangential light exposes the slightest micro-relief through harsh contrasts between shadow and bright areas, with no direct link to the millimetre tolerances for overall flatness.
On the technical side, SIA 242 precisely governs the conditions for acceptance of plastering and drywall work. The regularity of a partition is never assessed using an artificial light source aimed along the wall, nor through morning or evening sunrays sweeping directly across the surface. The standard appearance check requires diffuse lighting equivalent to the normal conditions of use of the room, together with a perpendicular viewing distance of at least one and a half metres. If the flatness measured under the two-metre straightedge is within the permissible deviations, the work is technically and contractually compliant.
| Inspection criterion | Recognised contractual practice | Abusive practice to be rejected |
|---|---|---|
| Direction of the light source | Diffuse lighting or the standard service lighting provided for in the project | Mobile spotlight or inspection lamp positioned at a raking angle against the facing |
| Viewing distance | Minimum distance of 1.50 m, perpendicular to the facing inspected | Raking view from a few centimetres away, aligned with the axis of the wall |
| Measurement of irregularities | Geometric check with the 2 m straightedge and the 20 cm rule | Subjective check based solely on the perceived cast shadow |
From level Q3 to level Q4: include the appropriate skim coating from the quote stage
To neutralise the visual impact of oblique light, standard joint treatment is not enough. Level Q2 is the standard of the trade: it comprises filling the joints and one finishing coat with sanding, suitable for textured finishes or matt paints without critical lighting. Level Q3 adds a wider jointing coat and additional smoothing, but a difference in absorbency remains between the board paper and the filler. Only level Q4 guarantees satisfactory behaviour under oblique light: it requires full-surface skim coating over the whole partition, creating a continuous film at least one millimetre thick that evens out the optical flatness and the grain of the substrate.
- Identifying critical lighting on the drawingsExamine the lighting layout to identify glazed bays without a lintel, perimeter LED strips and wall lights casting light along the partitions.
- Specifying level Q4 in the offerExpressly offer the Q4 option with full skim coating for exposed surfaces, detailing the skim coats and the corresponding drying times.
- Issuing a notice of incompatibilityIf the tender requires a Q2 finish for walls bordered by raking lights, record in writing the optical limits of the expected result before signing.
Under art. 365 CO, the contractor informs the client if a circumstance jeopardises the proper execution of the work. Where a contract specifies a Q2 finish while the architectural drawings provide for light coves grazing the walls, this duty to notify applies. This notice must be given at the time of the offer or award, not at the acceptance of the work. Once the partitions are finished, arguing that the wall meets the Q2 level ordered is no longer enough to defuse the dispute with site management dissatisfied with the visual result. Anticipating the issue in writing in the quote protects your work and your financial claims.
Inspection and acceptance under SIA 242: admissible lighting conditions
At the acceptance of plastering or drywall work, the reflex of running a site spotlight along a partition to pick out cast shadows is a frequent methodological error. Disputes about minimal undulations or band demarcations come almost exclusively from artificial lighting directed parallel to the facing. Yet SIA 242 strictly governs how interior surfaces must be examined during compliance checks.
A surface can fully meet the tolerances for overall flatness and offset while still showing relief under sharply directional light. The optical effect magnifies micro-variations in thickness of a fraction of a millimetre at the joints or screw heads. To establish the facts objectively in front of site management or the professional agent, the visual inspection must meet strict geometric and lighting criteria.
| Inspection criterion | Accepted inspection condition | Rejected inspection condition |
|---|---|---|
| Light source | Diffuse daylight or final light fittings in service | Site spotlight aimed along the wall, torch grazing the wall |
| Viewing distance | Direct frontal distance of two metres without magnifying instrument | Observation from a few centimetres away with an oblique view grazing the surface |
| Viewing angle | View perpendicular or axial to the plane of the facing | Extremely acute angle deliberately aimed at the light reflection |
| Flatness measurement | Two-metre aluminium straightedge and graduated measuring wedge | Subjective interpretation of the projection of shadows |
As long as the substrate meets the flatness deviations measured mechanically with the straightedge and no joint is discernible under normal lighting, the plasterer has fulfilled his duties for the standard levels. The presence of cast shadows under an unforeseen raking angle is not a legal defect of the work if the contractual requirement level has not been formally raised.
Contractual specifications and wording in the offer: locking in the required quality
Defending the compliance of a wall at acceptance remains a difficult exercise when the end client notices visual irregularities at dusk or under an architectural light strip. Even though SIA 242 protects the tradesman against abusive inspections, the commercial dispute often blocks the release of guarantee retentions. Raking light must therefore be dealt with upstream, from the stage of preparing the quote.
From the study of the detail drawings and the lighting concept supplied by the architect, the foreman or estimator must identify the sensitive areas. A glazed bay flush with a perpendicular wall, a skylight or light coves for LED strips systematically call for quality level Q4. This level involves a complete full-surface skim coating that masks the differences in texture between the board paper and the jointing compound.
- Identifying light sources on the drawingsLocate sliding doors, glazed transoms and built-in fittings that create direct raking light on the partitions or suspended ceilings.
- Specifying the surface level in the tenderCheck that the price series clearly distinguish standard areas in quality Q2 or Q3 from critical walls requiring full treatment in quality Q4.
- Drafting the technical reservation in the offerInsert a statement expressly specifying that under raking light only level Q4 limits shadows as far as possible, without however guaranteeing the total absence of visual effects.
- Joint validation of the test sampleProduce a representative sample surface on site before the general start of the plastering, inspected under the actual lighting of the project.
In the quote, the preliminary statement must clearly set out the limits of each finish level. State in writing that level Q3 reduces tool marks but is not suitable for raking accent lighting, and price the Q4 option as a separate item with its financial impact. If the client refuses this extra cost to save money, the written notification deprives him of any basis for disputing residual shadows when the acceptance record is drawn up.
Handling disputes at acceptance: protocol when raking light is used to challenge the work
When site management challenges the flatness of a partition or lining by shining a raking site spotlight on it, the discussion quickly bogs down if the contractual framework is not firmly recalled. A surface within the tolerances of level Q2 or Q3 will inevitably show micro-relief under sharp incident light. Faced with a rejection of the work or a financial retention, the team leader or site manager must neutralise the subjective assessment by bringing the inspection back to standardised conditions.
- Recall the agreed contractual levelImmediately cite the contract documents. If the quote stipulates a standard Q2 level or a Q3 without a raking light clause, the work cannot be judged against the requirements of a complete Q4 skim coating.
- Switch off mobile spotlights not provided forSIA 242 expressly defines the admissible inspection lighting. The visual assessment must be carried out in diffuse natural light or under the final artificial lighting provided for the use of the rooms, never under a raking LED lamp of a painter or plasterer.
- Carry out the geometric check with the straightedgeRaking light amplifies shadows without measuring actual deviations. Place the 2 m straightedge and the 20 cm rule to record the actual deflections in accordance with the tolerances of SIA 242. If the measured deviations are within the permissible millimetres, the surface is deemed to comply with the rules of the trade.
- Propose a remedial protocol with extra paymentIf the client nevertheless demands the complete disappearance of cast shadows caused by a full-height glazed bay or an unforeseen light strip, record the compliance of the existing substrate and price a complete Q4 skim coating as an addendum to the contract.
If the disagreement persists, the step is to draw up a written joint inspection record under SIA 118, recording the measurement of the deflections with the straightedge and the orientation of the light sources during the inspection. Any rework undertaken under duress without a written reservation amounts to acknowledging a non-existent execution defect. By setting the limits from the offer stage and strictly applying the acceptance protocol of SIA 242, the contractor protects his margins and defuses abusive claims.
Frequently asked questions
Can the architect reject a Q2 partition inspected with a raking inspection lamp?
No. Using a mobile light source directed parallel to the surface to hunt for imperfections is contrary to the assessment criteria of SIA 242. The visual examination of a plasterboard partition is carried out at normal viewing distance, under diffuse lighting or with the final light fittings in service. If the flatness measured with the two-metre straightedge is within the contractual tolerances of level Q2, rejecting the work is unjustified and unfounded.
Why does a perfectly flat joint cast a shadow under a glazed bay?
The phenomenon comes from the difference in texture and absorbency between the plasterboard paper and the jointing compound. Even if the physical transition is continuous and without excess thickness under the straightedge, raking natural light creates microscopic shadows on the micro-roughness of the plaster. Only a complete skim coating of level Q4 evens out the entire surface and removes this optical demarcation inherent in standard drywall construction.
How should the reservation on raking light be worded in the initial quote?
A clause specifying the finish level should be inserted: "Finish of facings to level Q2 in accordance with SIA 242. This standard level does not guarantee the absence of cast shadows under raking or tangential light. For areas exposed to large glazing or light coves, the application of a full skim coating of level Q4 must be the subject of a separate item or an extra agreed beforehand."
Who bears the extra cost if the customer demands Q4 smoothing at acceptance?
The client bears the full extra cost by way of addendum. Where the contractor has delivered a surface complying with level Q2 or Q3 as ordered in the contract, carrying out an additional complete skim coating is a change to the order after the fact. The plasterer prepares a supplementary quote covering the supply of the skim coating material, the labour hours for application, careful sanding and the adjustment of the construction site schedule before the painter steps in.
Texts and standards cited
- SIA 242Plastering, drywall and interior renders: definitions of surface quality levels and execution tolerances
- SIA 118General conditions for construction work: inspection of the work and notification of defects
