Skip to content
Website
🧱 CFC 271Dust, health and the plasterer's construction site managementChapter 2 of 10 in the section

Silica: cutting cement boards, saw and cumulative exposure

The drylining plasterer handles mineral dusts every day whose physiological effects are very different. While calcium sulphate causes a reversible mechanical irritation of the upper airways, the respirable quartz released by cement boards leads to incurable fibrous destruction. This chapter details how to identify the critical components, the routes of exposure and the cutting techniques that limit respirable dust.

Key takeaways

  • Plaster remains a nuisance dust, but crystalline silica causes permanent pulmonary fibrosis.
  • Cement-bonded and calcium-silicate boards release respirable quartz when cut with power saws in dry conditions.
  • Scoring with a scoring blade eliminates mechanical aerosolisation when fitting reinforced boards.
  • Cumulative exposure over a career requires source capture and absolute filtration.

Understanding the toxicity of silica and identifying the critical materials handled by the drylining installer

On an interior fit-out construction site, confusing gypsum dust with silica dust is a frequent error of judgement. Traditional plaster or plasterboard is made of calcium sulphate dihydrate. Occupational medicine regards this mineral dust as a non-specific nuisance: when inhaled in excess, it dries out the mucous membranes, stimulates bronchial secretion and mechanically obstructs the respiratory tract, but the body gradually clears it through the mucociliary escalator without triggering any destructive cellular transformation.

Respirable crystalline silica (quartz)
Fraction of mineral dust with a particle size below 5 micrometres, able to penetrate as far as the pulmonary alveoli. Insoluble, it triggers an inflammatory macrophage reaction leading to irreversible tissue scarring (fibrosis or silicosis) and significantly increases the risk of bronchial carcinoma.

Unlike gypsum, crystalline silica in the form of quartz has major tissue toxicity. When the plasterer works in shared wet rooms, ventilated façades under cover or technical rooms, plasterboard is replaced by specific facing boards that are highly resistant to water and mould. These technical materials incorporate Portland cement, mineral aggregates, expanded glass beads or pure silica fillers. The following table summarises the components handled under CFC 271 and their actual pulmonary hazard.

Common drylining materials and risk of quartz emission
Facing substrateMain compositionCrystalline silica fractionRisk level when dry-cut
Standard plasterboardCalcium sulphate dihydrate, celluloseTraces to negligible (less than 1%)Low (reversible bronchial irritation)
High-hardness plasterboardDensified gypsum, glass microfibresLow (less than 2%)Moderate (very fine abrasive dust)
Fibre-reinforced gypsum board for wet roomsGypsum, cellulose fibres, silicatesLow to moderateMedium (wearing a mask recommended)
Lightweight cement board (interior)Portland cement, expanded beads, textile meshHigh (5 to 25% depending on formulation)Critical (inhalation of respirable quartz)
Reinforced cement board / calcium silicateCement, siliceous sand, hydraulic limeVery high (can exceed 30%)Critical (immediate silicosis hazard)

The destructive mechanism rests on cumulative exposure over an entire working career. A quartz particle deposited in the pulmonary alveolus is engulfed by macrophages, which die and release biochemical mediators of fibrosis. The alveolar wall loses its elasticity and thickens. This process of fibrous scarring is irreversible and often develops over several decades, even after work on construction sites has stopped completely. Art. 82 LAA provides that the employer must take all measures for the prevention of occupational accidents and diseases that experience has shown to be necessary, that are applicable according to the state of the art and that are appropriate to the given conditions, while workers support the employer in particular by using protective equipment.

Adapting machining techniques and capturing cement dust at the source

To meet occupational health requirements, the company must eliminate the clouds of fine dust generated when erecting impact-resistant or water-resistant partitions. Dry cutting with a disc without a closed guard is a prohibited practice on Swiss construction sites because of the extreme concentrations of respirable dust released within seconds. Art. 3 OPA specifies that the employer must take the protective provisions and measures that meet the requirements of the ordinance, the other applicable occupational safety provisions and the recognised rules of safety engineering and occupational medicine.

  1. Cutting by mechanical scoring with a scoring bladeReference method for cement boards reinforced with a glass-fibre mesh. The installer scores the surface mesh along a straightedge with a carbide-blade knife, snaps the board along the supporting edge, then cuts the mesh on the back. This manual action involves no rotating speed and produces no respirable aerosol.
  2. Cross-cutting with a plunge saw guided on a railFor angled cuts, built-in window openings or calcium-silicate facings too dense to be snapped, a portable circular saw on a rail is required. The machine must be fitted with a fully sealed guard and connected to a controlled industrial dust extractor.
  3. Mechanical sawing on a water-fed tableWhen thick boards are repeatedly machined for acoustic or fire-rated technical partitions, setting up a water-fed table saw in an outdoor logistics area instantly traps silica particles in the cutting slurry, preventing them from becoming airborne.

When confined space or the complexity of the cut-outs forces the drylining installer to grind or saw cement boards overhead or in a service shaft, mechanical capture must be combined with personal respiratory protection. A disposable FFP3 filtering mask or a reusable half-mask with P3 filters protects the installer against the fraction that is not intercepted. Dry sweeping of offcuts and dust on the floor is prohibited in all installation rooms; cleaning is carried out by direct vacuuming with the class M dust extractor or by thorough prior wetting.

Low-emission cutting techniques: scoring blade, shears and wet sawing

On drylining construction sites, ordinary plaster dust is classed among the dusts with a reversible irritant effect: the upper airways and mucous membranes react with mechanical hypersecretion, but the calcium sulphate dihydrate particles are eventually dissolved and eliminated by the body without causing any structural degeneration of the alveoli. Conversely, cement-based boards (lightweight cement boards with textile reinforcement, calcium-silicate composite boards or mineral tiles intended for wet rooms and technical claddings) contain a significant fraction of free crystalline silica in the form of quartz. Once inhaled as ultra-fine respirable particles, these mineral edges do not dissolve: they cause a permanent inflammatory reaction of the pulmonary macrophages, leading to progressive and irreversible fibrosis, in which respiratory tissue turns into rigid scars.

Comparison of cutting methods for cement-matrix facings
Cutting methodLevel of respirable dust emissionSpecific toolingMain field of application in plastering
Scoring with a carbide scoring bladeNegligible (mechanical break without heating)Carbide-reinforced trapezoid blade or cement-specific cutter, metal straightedgeStraight longitudinal and transverse cuts on cement boards
Manual guillotine shears or nibblerVery low (dense, non-volatile chips)Workshop lever shears or slow electric nibblerRepetitive cutting of strips to length, layout of linings
Plunge saw with rail and water captureExtremely low (immediate suppression by the fluid)Diamond saw bench with continuous closed-circuit water supplyPrecise cut-outs, cutting for door frames and complex trapezoid shapes
Dry circular saw without extraction deviceCritical (massive exceedance of health thresholds)Standard diamond disc mounted on an angle grinder or bench sawStrictly prohibited at all workstations

To eliminate the risk at the source, the drylining installer systematically favours the score-and-snap method. The tungsten carbide scoring blade scores the glass-fibre reinforcing mesh and the surface cement matrix along an aluminium straightedge. Once the line has been drawn with a firm, deep stroke, the board is snapped by clean pressure over the edge of a bench or a stack of boards, exactly like a plasterboard. The reinforcement on the underside is then cut through from the back. This process produces no respirable aerosol, only coarse cement grains that settle immediately on the floor without remaining suspended in the volume of the room.

When the geometry of the work requires internal mitre cuts, angled cuts or penetrations for service ducts, motorised sawing becomes unavoidable. In this case, dry machining with a grinder without extraction is an intolerable practice that fills the entire floor with dust. The foreman then deploys either a plunge saw on a guide rail connected to a sawing tray with permanent water spray, or a machine fitted with a sealed guard and water injection at moderate pressure. The water binds the silica microparticles as soon as they are torn off by the diamond segment, creating a heavy slurry that is easily collected at the bottom of the recovery tray before settling.

OPA requirements, limit value and prevention of cumulative exposure

The ordinance on the prevention of accidents and occupational diseases requires the employer to arrange workstations and provide the technical installations necessary to eliminate any health hazard. On finishing work construction sites, the hazard linked to silica does not appear as an acute injury but as an insidious cumulative dose. A drylining plasterer who cuts cement boards without any capture device for a few minutes every day breathes in a volume of respirable particles that builds up over the years. Silicosis is a lung disease with a very long latency: the worker may remain symptom-free for two to three decades while developing a progressive loss of vital capacity, which frequently degenerates into severe respiratory failure or bronchial cancer.

Management of occupational exposure begins with the organisation of the quantity take-off and the planning of the installation. The foreman organises the cutting upstream by concentrating cuts in a dedicated ventilated area, isolated from the other trades, so as not to expose neighbouring workers. Using prefabricated elements or elements ordered to exact dimensions at the factory considerably reduces fitting operations on the slab. When cross-cutting cannot be carried out with water, source extraction through an absolute filter must be mandatorily supplemented by wearing personal respiratory protective equipment of high-efficiency class FFP3, correctly fitted to the face, with no beard interfering with the seal of the face seal.

Finally, the end of the shift is a critical moment that is often overlooked in the overall exposure assessment. Dry sweeping of a floor soiled with cement-board residues puts the finest silica fractions back into suspension, where they linger in the ambient air for several hours. The ordinance on construction work prescribes the removal of dust without dispersion: cleaning of workstations in plastering is carried out exclusively by industrial vacuuming with a high-efficiency filter or by wet scraping. This team discipline ensures that an apprentice or an installer does not suffer a silent toxic load during his or her years of professional practice.

Intervention protocol in case of uncontrolled emission and corrective measures

On a finishing work construction site in an enclosed space, uncontrolled cutting of cement-based composite boards instantly creates a dense fog of highly respirable dust. Unlike the calcium sulphate dust from conventional plaster, which temporarily irritates the oropharyngeal mucous membranes before being cleared, the crystalline silica dust from mineral fillers and cement penetrates deep into the pulmonary alveoli. There it causes permanent tissue fibrosis. Faced with a failure of the extraction, defective containment or improvised machining by dry cross-cutting, the team leader or foreman must neutralise the situation to protect the workers' health and comply with the requirements of the ordinance on construction work.

  1. Stopping the machines and evacuating the polluted spaceStop immediately any cross-cutting saws and circular saws that have no certified capture. Immediately evacuate the personnel present in the room who do not have adequate personal respiratory equipment. Lock access to the room to prevent any spread to the other finishing work trades.
  2. Wet clean-up and ban on sweepingStrictly ban dry sweeping and compressed-air blowing, which are the main causes of invisible respirable fractions being put back into suspension. Pick up chips and residual slurry with a damp sponge, or use a sealed industrial dust extractor fitted with filter cartridges for highly harmful substances.
  3. Switching to dust-free methodsRedo the entire layout, requiring manual cutting with the tungsten carbide scoring blade, by scoring the reinforcement mesh and snapping cleanly over a straightedge. Reserve any remaining motorised machining for tools fitted with permanent water spray or high-efficiency vacuum capture.
  4. Recording in the log and safety follow-upRecord the temporary stoppage and the corrective measures in the construction site log. Check the compliance of the workstations with the person responsible for safety, in accordance with the ordinance on the prevention of accidents, in order to assess the cumulative exposure load borne by the team.

Frequently asked questions

Why does a simple disposable dust mask not protect against silica when sawing cement boards?

Foldable filtering masks that do not seal tightly let part of the air through at the edges of the face during movement. The respirable fraction of crystalline silica measures less than five micrometres and easily passes through fit defects. To machine cement boards, respiratory protection must be combined with source capture using a certified dust extractor. Wearing a well-fitted tight-sealing half-mask remains an indispensable complement.

How does cutting with a scoring blade work on a fibre-reinforced cement board?

The tungsten carbide scoring blade scores the outer reinforcing mesh and the cement matrix at the surface. By scoring the board along a metal straightedge, then repeating the operation on the opposite face, the worker creates a clean mechanical break line. The board is then simply snapped over a rigid edge. This manual operation produces no kinetic heating and generates large, heavy chips instead of harmful respirable dust.

Why is cumulative exposure to silica more dangerous for the installer than exposure to plaster?

Gypsum dust partially dissolves on contact with body fluids and is cleared by the bronchial cilia. Crystalline silica, an extremely hard and insoluble mineral, remains trapped deep in the alveoli. The body triggers an inflammatory reaction that produces rigid scar tissue. Each exposure adds to the previous one with no possible elimination. Over the decades, this silent accumulation reduces the worker's respiratory capacity and can progress to disabling silicosis.

When is wet sawing mandatory for cutting cement boards on the construction site?

Wet sawing becomes unavoidable when the thickness of the boards or the complexity of angled cuts prevents the use of the scoring blade, particularly in poorly ventilated enclosed spaces. The water curtain instantly binds the mineral dust into a heavy slurry before it can become airborne. If moisture constraints rule out water, the contractor must use a circular saw under a sealed guard connected to an industrial dust extractor with absolute filtration.

Texts and standards cited

  • OPAPrevention of occupational accidents and diseases when using hazardous substances
  • OTConstProtecting workers' health and maintaining air quality at workstations

In the same section