Skip to content
Website
🧱 CFC 271Interior plasters: substrates, coats and smoothingChapter 6 of 10 in the section

Smoothing: finishing plaster, tightening with the smoothing trowel and tool marks

Smoothing a facing plaster requires a careful reading of the setting of the gypsum plaster or organic binder. By the end of this chapter, you will be able to determine the precise moment to put the trowel away so as not to glaze the substrate, prevent tension defects in the paint film and meet the requirements of SIA 242.

Key takeaways

  • Tightening is carried out as soon as the plaster loses its surface shine and begins to bleed evenly.
  • Excessive passes of the blade bring the binders to the surface and create a sealed, glazed crust.
  • A substrate that is too closed prevents mechanical keying and causes the paint to peel off or cord.
  • SIA 242 requires a uniform porosity without a mirror-like surface skin for high-quality finishes.

Identifying the setting window and dosing the pressure on the fine grain

Applying a fine-grain finishing plaster (generally below 0.2 millimetres) relies on a rigorous mastery of setting kinetics. Whether it is a mineral compound based on gypsum plaster mixed on the construction site or a ready-to-use paste plaster, the material undergoes a critical physico-chemical transition during evaporation and hydration of the binder. Applying the plaster with a stainless steel trowel requires a first levelling pass to dress the substrate, immediately followed by an indispensable resting time. Tightening the grain too early, while free water is still standing on the surface, displaces the paste instead of compacting it and creates unsightly ridges along the edges of the passes. Conversely, working too late on a film that has already crystallised causes microcracks through tearing of the binder.

Bleeding matt stage
Visual stage at which the fresh plaster changes from a shiny, liquid appearance to a matt, firm texture, signalling the removal of free surface water and the start of stiffening of the crystalline network.
  1. Laying and thickness settingSet the film thickness between 0.5 and 1.5 millimetres using a smoothing trowel held at an angle of 30 degrees, without applying excessive pressure on the base.
  2. Waiting for desaturationObserve the surface until the damp film has disappeared completely; a finger placed on the plaster must no longer pick up paste but leave a slight impression.
  3. Single mechanical tighteningLay the blade at 15 degrees and make a fluid, continuous movement to flatten the edges and orient the fine grains without bringing liquid back to the surface.

The force applied to the handle of the smoothing trowel must change in proportion to the consistency of the product. During the finishing pass, the blade no longer seeks to unload or level material, but to compact the microporosity while keeping an open surface. A good plasterer recognises this point of balance by the clear metallic sound of the tool: a muffled squeak indicates material that is still too wet, whereas a dry scraping sound signals the start of burning of the plaster, which requires an immediate stop to manual passes so as not to tear off the peripheral grains.

Stopping the smoothing in time to preserve the porosity required by SIA 242

The most widespread mistake on construction sites when seeking a flawless surface is to multiply the blade passes until a polished, shiny appearance is obtained. This forced burnishing causes a surface migration of the ultrafine particles of calcium carbonate, resins or lime, forming a vitrified skin with no capillary network. According to SIA 242, surfaces intended to receive paint must have a flatness and fineness of grain that comply with the contractual quality levels, while imperatively retaining their absorption permeability. A substrate made impermeable prevents the primer resin from penetrating, which seriously compromises the mechanical adhesion and durability of the subsequent coatings applied by the painters.

Appearance requirements and tightening limits according to SIA 242
Quality levelExpected visual appearanceRisk of surface glazing
Q2 (Standard)Levelling pass without ridges, even plaster grainLow: simple removal of smears
Q3 (Special)Fine closed finish, pores filled, edges smoothed outMedium: risk of localised burnishing at repairs
Q4 (Superior)Complete continuous plastering, flatness under raking lightHigh: critical risk of overall vitrification

When the painter works on a plaster or finish that is too tight, the paint cannot wet the substrate in a balanced way. The paint film slides over the vitrified base, drags abnormally under the roller and lays out poorly, causing premature flaking, blisters or a very pronounced orange-peel effect under raking light. To avoid this recurring interface dispute between trades, the drywall plasterer must stop all handling as soon as the traces of re-working have faded and the matt appearance sets in. Any remaining smears are then removed by light dry sanding with fine abrasive paper (grit 180 to 220), never by stubbornly crushing them with the metal trowel.

Glazing of the plaster and adhesion defects for the painter

Excessive tightening of the finishing plaster with the stainless steel trowel or the Flemish spatula irreversibly changes the surface structure of the substrate. Under the effect of repeated passes and too much pressure applied in the final phase of setting, the residual water rises by forced capillarity, carrying the ultrafine fractions of mineral binder or polymers to the outside. This concentration forms a compact skin, smooth as a mirror, commonly called trowelling laitance or glazed surface. By crushing the fine grain of the plaster instead of simply compacting it to refusal, the plasterer destroys the microporous network that is indispensable for normal hygrometric exchanges.

For the painter (CFC 272) who works after the handover of the work, a substrate vitrified in this way causes immediate application difficulties. The lack of capillarity prevents even impregnation of the primers or base coats. The water or solvent of the paint cannot penetrate into the surface pores of the plaster: the paint film stays on the surface, spreads poorly and begins to dry by surface evaporation without anchoring mechanically. As the roller passes, the paint sticks to the sleeve and is subjected to excessive pull. This phenomenon, commonly described on construction sites as paint that "drags", causes local tearing, unsightly build-up, lifting of the film when the second coat is applied, and even blistering under tension.

SIA 242 defines the requirements for plastering work and reminds us that the surface must have a uniform texture and a porosity compatible with the agreed subsequent coatings. While a surface quality grade Q3 or Q4 requires rigorous flatness under raking light and the systematic removal of spray or tool marks, it must on no account be confused with a sealing mechanical polish. The grain of the finishing plaster, generally ranging from zero to a few fractions of a millimetre depending on the formulation, must keep its granular framework intact immediately beneath the stop skin.

Porosity diagnosis, repair and acceptance tolerances

To validate that an interior plaster is neither too porous nor vitrified before releasing the work area, the team leader or site manager has reliable empirical methods. The water-drop test is the quickest site test: a drop placed on the facing must be absorbed gradually without running off instantly or standing on the surface indefinitely. A drop that beads without change for several minutes signals a substrate completely blocked by excessive bleeding of binder.

Behaviour of the plaster facing according to the degree of tightening with the tool
Surface conditionGrain and pore structureBehaviour during paintingCorrective action required
Under-tightened (lack of pressure)Open pores, loose grain, micro-cavities and visible edge marks.Abrupt absorption of the binder water; accelerated dulling and dusting.Application of a second thin pass or a skim coat to level.
Correctly tightened (according to SIA 242)Evenly compacted grain, continuous and matt capillary porosity.Even wetting of the primer coat, uniform tension of the film.No rework; standard dust removal before painting.
Over-tightened (glazed / burnt)Sealed surface film, dense laitance, grain completely drowned.Poor adhesion, tearing under the roller, risk of later flaking.Careful mechanical sanding to reopen the grain mechanically.
  1. Visual and tactile identificationLocate shiny reflections under raking light as well as areas of extreme slipperiness to the touch along the passes of the smoothing trowel.
  2. Controlled mechanical sandingSand using an orbital sander connected to a vacuum cleaner or a hand sanding block, with a medium abrasive grit, in order to break the laitance film without cutting into the fine plaster layer.
  3. Checking the openness of the substrateCheck that the lustre has disappeared completely and repeat the water absorption test to confirm that uniform capillarity has returned over the whole substrate.
  4. Removal of residual dustVacuum the treated surface thoroughly so that the sanding dust does not form a powdery screen that is harmful to the reception of the base coats.

Repair of a glazed facing is the plasterer's responsibility before the handover record of their package. Carrying out an opening sanding as soon as the plaster is completely dry makes it possible to meet the appearance criteria defined in the works specifications and avoids cross-disputes between trades when the paintwork is being prepared. The right professional gesture lies in moderation: the trowel must glide over the crest of the grain without ever trying to wring out the material to make it shine.

Reworking glazed surfaces and base rehabilitation protocol

When excessive tightening with the stainless steel trowel has brought the fines and binders to the surface, the plaster shows a characteristic vitrified shine. This localised or general glazing removes the natural capillarity of the material: the water-drop test shows immediate beading. The substrate, now sealed, no longer absorbs evenly, which will inevitably cause, during the painting work, poor adhesion, excessive dragging of the material, dull patches and detachment of the dry film. At this stage of setting, any further burnishing or addition of water worsens the damage by creating a surface skin with no cohesion.

  1. Mechanical sandingCarry out dry sanding using an orbital sander fitted with an abrasive of suitable grit (P120 to P150), without dwelling, so as not to attack the core of the plaster or damage the board facing beneath. The aim is solely to abrade the sealed surface crust.
  2. Dust removal and checkingRemove all dust completely by industrial vacuum extraction. Repeat the surface absorption check with a damp sponge: wettability must become uniform again over the whole panel.
  3. Levelling skim coatIf micro-scratches or hollows appear after the substrate has been reopened, apply an extra-fine finishing plaster pulled to zero, limiting the pressure and stopping work as soon as it is flush, without closing the pores again.

The finding must be recorded jointly before the paint applicator intervenes. In accordance with the rules of SIA 242, the plasterer delivers a base with a defined surface quality grade, but also a porosity compatible with the finishing products of CFC 272. If sanding alone is not enough to restore an open, uniform texture, applying a specific primer coat must be agreed on the construction site between the site management and the two trades, in order to avoid any later dispute over responsibility for detachment.

Frequently asked questions

How do you rescue a wall section whose plaster has been completely glazed?

The only remedy is to mechanically open the vitrified surface. A long-reach drywall sander connected to a vacuum cleaner is used with an abrasive disc of grit P120 or P150. The sanding must break the thin tightening crust without cutting into the plaster beneath. After all the dust has been vacuumed up, a visual check and a wetting test verify that the substrate has regained an even porosity, with no residual shine.

Why does paint drag more on an over-tightened plaster than on a normally finished plaster?

When the trowel closes the substrate excessively, the porosity becomes uneven or almost nil. The water contained in the paint does not penetrate into the base and stagnates under the roller, or on the contrary concentrates on the few porous areas that have not been burnt. The painter then notices that the product dries poorly, slides without gripping or drags in jerks, causing lap marks, dull patches and a lack of opacity.

At what precise moment of setting must you absolutely stop passing the trowel?

Tightening must be stopped as soon as the plaster loses its initial shiny lustre to become matt and the material offers noticeable resistance to the advance of the blade. If the trowel starts to scrape with a dry squeak or if small ridges tear off, crystallisation is too far advanced. Persisting at this moment destroys the internal structure of the plaster or brings up a sealed, non-adhering skin.

Who bears the financial cost of repairing an over-closed plaster on the construction site?

Preparation and porosity of the substrate are the plasterer's responsibility under SIA 242. If the delivered plaster shows glazing that prevents normal adhesion of the paints of CFC 272, the plasterer must correct the defect at their own expense by mechanical sanding. The painter nevertheless retains the duty to check the substrate before applying the primer coat and to give notice if the base is unsuitable.

Texts and standards cited

  • SIA 242Plastering, rendering, drywall construction: surface quality requirements and execution tolerances

In the same section