Key takeaways
- A rigid connection between concrete and fired clay cracks under the effect of differential shrinkage of the substrates.
- The glass-fibre mesh must extend at least twenty centimetres on each side.
- The mesh is embedded in the outer third of the fresh mortar and must never touch the bare substrate.
- Service chases require a filling mortar that has hardened before the whole area is fully meshed.
Understanding differential movements and reinforcing the concrete-against-masonry junction
On a building construction site, direct contact between a reinforced concrete wall and a masonry wall of fired clay bricks or calcium silicate forms a continuous physical break. These two components do not react in the same way to thermal and moisture variations. Concrete undergoes hydraulic shrinkage spread over several months, whereas fired brick shows very little dimensional variation, or even a slight residual swelling. Without a suitable decoupling or bridging measure, the interior plaster, whether gypsum or cement-lime, absorbs all of the shear created by this joint plane. The crack then inevitably appears at the surface, straight, following the line where the substrates meet.
To ensure the bridging is effective, the plasterer uses a glass-fibre mesh fabric treated against alkaline attack, with a standard mesh size of 4 x 4 mm or 5 x 5 mm. The most common mistake is to apply the mesh strip dry directly onto the wall before spraying the plaster. Reinforcement pressed against the bare substrate performs no mechanical function: it acts as a separator and causes the plaster layer to detach. The reinforcement must absolutely float in the first third of the total plaster thickness, on the face side.
| Junction configuration | Minimum reinforcement width | Overlap on each side | Recommended application |
|---|---|---|---|
| Flat junction between concrete wall and fired clay block | 500 mm | 250 mm | Embedded in the first fresh, levelled coat |
| Internal corner between dissimilar materials | 400 mm | 200 mm | Careful folding without tension in the arris |
| Partition abutment on load-bearing column | 400 mm | 200 mm | Fitted centred on the decoupling strip |
| Overlap of two mesh sheets | Variable strip width | 100 mm | Overlap pressed in without excessive build-up |
Filling service chases and embedding the reinforcement in accordance with good practice
Chasing in electrical conduits and plumbing pipes locally weakens masonry walls. Hasty filling of these trenches creates an unstable zone at the heart of the substrate. When the plasterer comes to apply the full plaster coat, the chase presents a double weakness: the heterogeneity between the filling mortar and the substrate block, and the risk of differential shrinkage increased by a locally large thickness. A methodical treatment in several staggered coats determines the durability of the finished surface.
- Dusting off and dampening the chaseRemove cutting dust and rubble with a brush or an industrial vacuum cleaner. Dampen the fired clay walls to avoid premature drying out of the filling mortar.
- Filling flush with the raw surfaceFill the cavity with a slow-setting building plaster or a compatible bedding mortar. Pull the material with the trowel, leaving a slight recess of two to three millimetres relative to the general plane of the masonry.
- Waiting for the filling to dry completelyNever apply plaster over fresh filling. Evaporation of water and bulk shrinkage must be complete in order to stabilise the volume of the chase.
- Applying the plaster bed and pressing in the meshApply a first coat of plaster along the axis of the trench. Unroll the mesh with a width at least twenty centimetres greater than the chase. Press the mesh in from top to bottom with the stainless steel float so that the binder is forced through the mesh.
- Covering and finishing compactionImmediately cover the mesh with the second coat of plaster, wet on wet. Smooth the surface so that the pattern of the textile mesh is completely hidden.
On wide chases containing several bundles of services, the standard strip width of twenty centimetres is no longer sufficient. The reinforcement zone must extend beyond the edges of the cut by at least ten to fifteen centimetres on each sound edge. If the substrate is in a degraded condition or shows local detachment, the tradesperson records the situation: the Code of Obligations (CO), in art. 365 CO, provides that if a circumstance jeopardises the proper or timely execution of the work, the contractor must immediately inform the client. In practice, on Swiss construction sites, this written notification allows the structural reinforcement of the area to be validated before finishing work starts.
Fitting the bridging mesh and overlap rules according to SIA 242
Direct contact between two substrates of different natures, typically a reinforced concrete wall or column cast in place against a masonry of fired clay bricks or calcium silicate, constitutes an obvious mechanical break. Differing moduli of elasticity, asynchronous hydraulic shrinkage and thermal variations create shear stresses at this joint. According to SIA 242, applying a gypsum plaster or a cement-lime plaster without a specific constructional provision inevitably leads to linear cracking visible through the finish. The plasterer must neutralise these differential movements by interposing a reinforcement capable of distributing the stresses over a larger area.
To guarantee the effectiveness of the reinforcement, the reinforcing strip must never be sized at the bare minimum. A total width of 40 to 50 cm is required to ensure symmetrical anchorage of at least 20 cm on each material. The mesh used in interior plasterwork consists of a woven glass-fibre netting, necessarily treated against the alkalinity of mineral binders, with a weight of at least 110 to 160 g/m² and a mesh size between 4 x 4 mm and 10 x 10 mm. A mesh that is too fine prevents the paste from passing properly through the fabric, forming an air pocket that cancels adhesion; a mesh that is too wide does not restrain shear microcracks.
| Junction configuration | Foreseeable movements | Total strip width | Position within the plaster thickness |
|---|---|---|---|
| Cast-in-place concrete against fired clay brick | High differential shrinkage and thermal expansion | 50 cm (25 cm on each side) | Upper third of the base coat |
| Concrete against calcium silicate block | Moderate shear, differing capillary absorption | 40 cm (20 cm on each side) | Upper third of the base coat |
| Filled service chase (> 50 mm) | Drying shrinkage of the filling mortar | Chase width + 20 cm (10 cm on each side) | Half the thickness of the base coat |
| Masonry junction against blind box or lintel | Mechanical vibrations and thermal shocks | 30 to 40 cm depending on the lintel bearing | Embedded flush beneath the finishing coat |
The reinforcement only works if it acts in pure tension. Dry fixing pressed directly against the raw wall, before the plaster is sprayed on, is a major execution defect. The sprayed mortar cannot properly coat the glass strands on the joint-bottom side, leaving the mesh free to float with no bond to the masonry. The mesh must always be pressed into the first coat of plaster while it is still fresh, then immediately covered so that it sits in the surface third of the base coat.
Treatment of filled service chases and control of ghosting
Chases made for embedding electrical or plumbing conduits introduce a linear discontinuity comparable to a change of substrate. Even when the filling by the responsible trades has been executed flush with cement mortar or masonry plaster, the filled zone behaves hygrometrically and mechanically independently of the load-bearing wall. The shrinkage of the filling product as it sets almost systematically causes a perimeter shrinkage crack along the line of the chase if the plasterer has not fitted any bridging reinforcement.
- Checking the substrate and regulating the backgroundCheck the hardness and levelling of the filling mortar. Brush off powdery residues, dust off carefully and apply a suitable background regulator or mineral bonding bridge to even out the porosity between the raw wall and the technical filling.
- Mixing and applying the first coatSpray or hand-apply a first base coat of plaster over a width exceeding the chase zone by 15 to 20 cm on each side. Pull the material with the straightedge or level it without smoothing.
- Pressing in the mesh stripUnroll and centre the glass-fibre mesh strip on the axis of the chase in the still-fresh plaster bed. Press the fabric in with the notched float or stainless steel trowel in regular passes, from the centre to the edges, without forming creases or stretching the mesh.
- Covering and compactionImmediately apply a second coat of mortar so as to completely embed the reinforcement under 2 to 3 mm of material. Compact the surface with the spatula or notched plane to prepare the key for the smoothing plaster or the finishing felt coat.
In addition to the structural risk of cracking, differences in water absorption between the chase filling and the surrounding masonry produce persistent visual ghosting. Plaster applied on a heterogeneous background dries faster on porous areas than on a rich mortar or smooth concrete. If the plaster is floated or smoothed while the moisture of the paste is not uniform, the surface grain and the density of the finish show variations that remain visible in raking light, even after execution to quality level Q3 or Q4. Systematically applying a regulating primer over the entire wall before general levelling is the only effective remedy against these appearance defects.
Managing defects: crack diagnosis and reinforcement repair
When the ghost line of a junction between fired clay masonry and reinforced concrete shows through the interior plaster, the plasterer must identify the origin of the defect before any repair. Two causes dominate: the outright omission of the textile reinforcement during the base coat, or a mesh pressed dry against the substrate instead of being pressed into the first fresh third of the mortar. Without complete embedding, the glass grid takes up no shear stress arising from the differential shrinkage of the materials.
- Stripping back and opening the areaOpen the crack with a raking tool or an angle grinder fitted with dust extraction. Remove the unbonded plaster on each side over a strip of at least 200 mm to reach sound substrate and expose the original line of rupture.
- Stabilising the chase or the junctionDust off carefully and dampen if the background is an absorbent mineral one. For a sunken filled service chase, cut out the friable mortar and fill with fast-setting plaster or cement-lime mortar to restore flatness.
- Incorporating the bridging meshApply a first coat of compatible plaster mortar. Press in an alkali-treated glass-fibre mesh, observing the overlap width prescribed by SIA 242, i.e. a minimum overhang of 100 to 150 mm on each side of the junction.
- Finishing and compactionCover the reinforcement without delay with the second coat of plaster, wet on wet. Level with the straightedge, then compact with the sponge float or trowel to reproduce the surrounding texture before it dries completely.
If the structural movement remains active, in particular on the underside of a concrete slab subject to continuing deflection, incorporating an embedded reinforcement is no longer sufficient. A clean, straight separation joint must then be formed at the masonry-concrete junction, closed with a decoupled profile or a flexible joint backing suited to the expected deformations.
Frequently asked questions
What is the minimum overlap width to be observed between two sheets of plaster mesh?
On a standard junction or when continuing a run, SIA 242 and good practice require an overlap of at least 100 mm between the sheets of reinforcing mesh. At external corners or on heavily stressed junctions such as the concrete-fired clay contact, this margin must reach 150 mm of overhang on each side of the potential crack to ensure effective transmission of tensile stresses.
How do you correctly reinforce the plaster over a wide filled chase?
A chase filled for service conduits must first dry right through so that the filling mortar completes its shrinkage. Before applying the smoothing plaster, the plasterer applies a first coat of mortar in which a strip of glass-fibre mesh is embedded. This reinforcement must extend at least 100 mm beyond the edges of the chase onto sound masonry walls.
Can the reinforcing mesh be fixed with staples directly onto the wall before plastering?
No, this method weakens the work. Textile reinforcing mesh only works in tension if it is perfectly embedded in the body of the mineral plaster. Fixing the grid dry against the concrete or brick presses the reinforcement against the background: the mortar does not pass behind the mesh, the bond remains incomplete and the plaster cracks at the slightest thermal movement or differential moisture shrinkage of the substrate.
Why does a crack systematically appear at the junction between a concrete lintel and a fired clay wall?
Cast-in-place concrete and fired clay brick have totally different coefficients of thermal expansion and rates of hydraulic shrinkage. Concrete shrinks and deflects under load while the masonry remains stiffer. Without a bridging mesh embedded in the plaster across this material discontinuity, the concentration of shear stresses inevitably shears the surface layer of plaster.
Texts and standards cited
- SIA 242Plastering, rendering, drylining: application requirements for mineral plasters and bridging of heterogeneous substrates
