Skip to content
Website
🧱 CFC 271Suspended ceilings: suspension, slab deflection and access hatchesChapter 2 of 10 in the section

Suspending: hanger spacing, load per square metre and recessed luminaires

After this chapter, you will be able to size precisely the spacing of hangers and carrying profiles for a suspended plasterboard ceiling. From the preparatory phase, you will take into account the dead weight of the linings, the insulation and the point loads of luminaires or ventilation outlets, while selecting fixings suited to the bare substrate.

Key takeaways

  • Always size the grid by adding together the lining, the insulation and the recessed fittings.
  • The SIA 242 standard limits the permissible deflection in order to preserve the flatness of the joints.
  • Any heavy point load requires a reinforced framework or a dedicated independent suspension.
  • Match the mechanical anchorage to the exact nature of the substrate, between solid concrete and hollow-block slabs.

Calculate the actual total load before fixing the framework grid

A common mistake on construction sites is to size the framework of a suspended ceiling by taking into account only the self-weight of the plasterboard lining. In practice, the subsequent addition of a mineral wool blanket, large-format recessed luminaires, air supply outlets or access hatches considerably increases the weight per unit area. A grid calculated too tightly deflects under this deferred overload, causing micro-cracks at the joints and unacceptable unevenness under raking light.

Suspended ceilings must be designed and built so as to support their own weight and the foreseeable additional loads without the residual deflection compromising the appearance of the work or the safety of users.

norme SIA 242

According to SIA 242, the sizing of the primary structure (carrying profiles) and secondary structure (furring channels) follows directly from the total load per square metre. For a standard ceiling under a concrete slab with a single 12.5 mm cardboard-faced plasterboard lining, the basic dead weight is approximately 9 to 10 kg/m². However, adding 60 mm of acoustic insulation adds approximately 2 to 4 kg/m², while a concentration of LED spotlights, transformers and technical ducts can add 3 to 5 kg/m² distributed. Once the 15 kg/m² threshold is exceeded, the maximum permissible spacings must be reduced.

Indicative permissible spacings for double metal framework (CD 60/27 profiles)
Estimated total load (kg/m²)Max. hanger spacing (mm)Carrying profile spacing (mm)Secondary profile spacing (mm)
Less than 15 kg/m² (1x standard BA13)10001000500
15 to 30 kg/m² (1x BA13 + insulation + luminaires)900900500
30 to 50 kg/m² (double lining or heavy acoustic)750800400

Mechanical fixing to the bare substrate and treatment of point loads

The mechanical strength of the suspended assembly rests on the connection between the hanger and the load-bearing slab. A failure at this anchor point endangers the stability of the work. The dry-lining plasterer must determine the anchor type according to the composition of the structural work. Art. 365 para. 3 CO also requires the contractor to inform the client if a supplied substrate jeopardises the proper execution of the work.

  1. Identify the exact nature of the bare ceilingDistinguish unambiguously between a solid reinforced concrete slab, a hollow-block floor with prestressed joists and a timber-joist floor. Standard expanding plastic plugs are strictly prohibited for suspending continuous ceilings.
  2. Select the certified anchorOn solid concrete, use only all-metal drive-in anchors (ceiling nails) or concrete screws without plugs certified for tensile loads. In hollow blocks, use spring toggle anchors or metal toggle anchors that open out inside the cavity.
  3. Reinforce trimmed openings and cut-outsWhen the electrician or the ventilation installer creates an opening that interrupts a secondary profile, form a rigid trimmer frame using framework profiles and suitable splice pieces, taken directly onto the adjacent carrying profiles supported by dedicated hangers.

Beyond 5 kg, as for stage spotlights, air-conditioning cassettes or suspended hoods, the load must on no account be transferred to the plasterer's framework, even if doubled. Such appliances require an independent suspension fixed directly to the structural work, carried out by the electrical or sanitary installers (CFC 232 and CFC 250). The plasterer provides only the framing, the perimeter shadow gap or the neat finishing of the lining around the technical housing.

Sizing the spacings according to the combined total load

The sizing of a suspended ceiling does not stop at simply calculating the self-weight of the plasterboard. On construction sites, the classic mistake is to adopt the maximum permitted spacing for a standard lining without including the mass of the thermal or acoustic insulation laid in the plenum, nor the cumulative weight of the recessed technical fittings. LED light fittings, ventilation diffusers and access hatch frames constitute point and distributed linear overloads that bear directly on the secondary profiles and the layer of carrying profiles.

The SIA 242 standard sets the deformation requirements for suspended ceilings in dry construction. To prevent any visible sagging or cracking of the joints between boards, the whole framework must be sized so that the residual deflection under total load does not exceed the permitted tolerances. A ceiling calculated too tightly when empty shows an instantaneous deflection from installation, which increases over time through the creep of the materials and the airflow vibrations transmitted by the ventilation ducts.

Chart of hanger and profile spacing according to the total load per unit area (boards, insulation and fittings)
Total load per unit areaSpacing of secondary profiles (furring channels)Spacing of primary profiles (carrying profiles)Maximum distance between hangers
Up to 15 kg/m² (1x 12.5 mm board, no heavy overload)500 mm1000 mm900 mm
From 15 to 30 kg/m² (2x 12.5 mm boards or 1x board with insulation and luminaires)400 mm900 mm800 mm
From 30 to 50 kg/m² (dense acoustic linings, compact insulation, fittings)400 mm750 mm650 mm
Over 50 kg/m² (armoured systems or heavy technical false ceilings)300 mm to 400 mm600 mm550 mm

Once light housings or supply air outlets exceed a unit load of 3 kg, they can no longer rest freely on the plasterboard lining. This load must be added to the average mass per square metre of the area concerned in order to tighten the hanger grid, or be taken by an independent mechanical support secured to the bare slab above.

Fixing to the structural work and reinforcing openings

The full transmission of permanent and imposed loads depends on the anchorage of the hanger in the load-bearing substrate. The choice of fixing element depends solely on the geological and mechanical nature of the bare ceiling. In a cast-in-place reinforced concrete slab, fixing is carried out using drive-in metal anchors or concrete screws approved for cracked concrete in the tension zone. Plastic plugs or light drive-in plugs are strictly prohibited for carrying loads in continuous suspension from the ceiling.

  • Solid reinforced concrete slabs: drilling with a hammer drill with depth stop, form-locking expansion metal anchor or concrete anchor screw without plug.
  • Hollow-core prestressed concrete slabs: anchoring is mandatory in the walls of the cores using metal toggle anchors or approved hollow-block plugs, without cutting into the prestressing reinforcement.
  • Timber-joist floors or mixed timber-concrete structures: fixing with fully threaded screws anchored in the axis of the load-bearing joists to a minimum depth set by the manufacturer, never taken into mere boarding.
  • Metal substrates (ribbed steel decking): joist suspension clamps or specific self-drilling screws taken onto the upper ribs in accordance with the structural recommendations.

For large openings, a reinforcing frame made of carrying profiles must always be built. This frame relieves the cut furring channels and redistributes the forces to additional hangers placed less than 100 mm from the corners of the cut-out. When planning on the drawings, the site manager checks the coordinates of the HVAC and electrical appliances so as to position the primary carrying profiles outside the insertion zones, thus ensuring a rigid installation compliant with the rules of dry construction.

Handling unforeseen overloads, sagging and framework repair

On construction sites in French-speaking Switzerland, the late discovery of uncoordinated technical equipment is the main cause of defects in suspended false ceilings. If an electrician installs massive luminaires or a ventilation installer fits air diffusers without independent suspension, the actual load per unit area exceeds the sizing class provided for in the contract. The plasterer foreman then observes, with a rotating laser level, an abnormal deflection clearly above the appearance tolerances of the SIA 242 standard. As soon as excessive deflection of the primary framework is measured before or during the works, the installation of the plasterboard lining must be stopped.

  1. Joint measurement of the deflectionCheck the flatness beneath the carrying profiles using a three-metre straightedge and a laser level. Record the unit weight of each recessed fitting and quantify the residual deflection against the admissibility criteria.
  2. Formal notice to site managementSend site management a detailed written report pointing out the technical overload not provided for in the tender drawings. Notify that the hanger spacing in place is incompatible with the actual weight of the added appliances.
  3. Adapting the grid and carrying profilesWhile the ceiling is still open, tighten the spacing of the primary profiles and install intermediate hangers. Require the other trades to suspend any appliance over three kilos directly from the bare slab by means of dedicated threaded rods.
  4. Checking the anchors in the structural workMake sure that the metal anchors for cracked concrete or the toggle anchors for hollow-core slabs support the recalculated total load per unit area, in accordance with the SIA 242 standard and the manufacturers' technical data.

In a dispute arising after acceptance of the work, the technical expert distinguishes the structural deformation of the load-bearing slab from the deflection of the ceiling's own metal framework. The plastering firm protects itself by proving, through its site records, that the hanger spacing strictly complied with the contractual mass per unit area, and that the technical equipment was added without prior technical coordination. Under the Code of Obligations (CO) and the SIA 118 standard, the costs of removal, reinforcement of the framework and reinstatement of the finishes fall on the firms that overloaded the assembly without agreement.

Frequently asked questions

What is the maximum permissible load on a carrying profile without adding a dedicated hanger?

On a standard metal profile framework, the maximum permitted load for a point fitting does not exceed three kilograms fixed between two framework points. Beyond this value, the SIA 242 standard requires the load to be transferred directly to the bare slab by means of a threaded rod, or an additional hanger with a bracing profile to be added. Any heavy luminaire or bulky air diffuser requires a mechanical suspension independent of the ceiling framework.

How are hangers fixed beneath a concrete slab with composite decking?

Fixing to composite decking must be made in the concrete ribs and never in the steel sheet alone, unless the floor manufacturer gives specific technical approval. The plasterer uses fixings approved for cracked concrete or claw brackets suited to the profile of the metal decking. The hanger spacing must be aligned with the pattern of the decking corrugations, which often means tightening the carrying profiles to meet the requirements of the SIA 242 standard.

What spacing should be chosen when fitting a double layer of plasterboard on a framework?

For a double lining of two 12.5 mm boards, the self-weight reaches approximately twenty kilos per square metre. With this increased weight, the spacing of the carrying profiles is generally reduced to eighty or ninety centimetres, while the spacing of the hangers on the carrying profiles is reduced to sixty-five or seventy-five centimetres. This sizing ensures compliance with the permissible deflection limit set by the SIA 242 standard and avoids any visible deformation under raking light.

Who must bear the cost of structural reinforcement if diffusers are added after the fact?

If ventilation appliances are positioned after the framework has been installed without appearing on the approved execution drawings, responsibility lies with site management or the requesting trade. The plasterer issues a notice of additional cost for partial dismantling, the supply of additional profiles and extra anchoring into the bare slab. The modification work must be covered by a daywork order or a written addendum in accordance with the SIA 118 standard.

Texts and standards cited

  • SIA 242Plastering, rendering, dry construction - Execution requirements and tolerances
  • SIA 118General conditions for the execution of construction work
  • Code des obligationsGeneral rules of the contract for work, notice of defects and liability

In the same section