Key takeaways
- The residual deflection of a concrete slab directly loads any partition built in rigid contact with it.
- Without a sliding track, the studs buckle and the upper joints burst.
- SIA 242 requires the framing heads to be decoupled under deflecting floors.
- A clearance of at least fifteen millimetres absorbs the deformation without a major extra cost in hardware.
Understanding residual deflection to prevent partitions from being crushed
On a building construction site, the structural work delivers reinforced concrete floors whose mechanical stabilisation takes several years. Even after formwork removal and initial drying, the slab keeps deforming under the combined action of concrete creep, hydraulic shrinkage and the imposed service loads such as screeds, furniture and occupants. This delayed deformation is the residual deflection. When a plasterboard partition is built rigidly between two slabs, it unintentionally becomes a load-bearing element as the upper level sinks towards the middle of the spans.
Lightweight metal-stud partitions have no admissible load-bearing capacity. If the top track is fixed to the ceiling and the vertical studs and plasterboards butt against the bottom of this section, the load path crushes the whole assembly. The vertical forces then cause lateral buckling of the galvanised steel studs, shearing of the self-drilling screws and visible bulging of the facings. On the surface, the consequences are immediate: horizontal cracking along the cornice, bursting of the joint tapes in the corners and complete jamming of the door units built into the run.
Under a contract for work governed by Swiss law, art. 365 para. 3 CO requires the contractor to inform the client immediately if a circumstance jeopardises the proper or timely execution of the work. Noticing the absence of a provision for floor movement when accepting the substrates is an integral part of this duty of technical vigilance of the dry-lining contractor.
Installing the sliding head according to SIA 242
SIA 242 defines the requirements for plastering and dry-lining work, in particular the treatment of connections between non-load-bearing walls and deformable structures. The head connection must absolutely guarantee sufficient vertical freedom to allow the foreseeable lowering of the slab without transmitting any mechanical stress to the stud network or the facing. For this purpose, the conventional installation with a standard track is replaced by a long-flange U-section system or by a specific sliding section fitted with guide sliders.
| Calculated deflection | Top section | Clearance under slab | Board overlap |
|---|---|---|---|
| Up to 10 mm | U-section with 40 mm flanges | 15 mm | Cover strip 20 mm |
| 10 to 20 mm | U-section with 60 mm flanges | 25 mm | Cover strip or recessed joint 35 mm |
| Over 20 mm | Telescopic section with sliders | 35 mm | Specific metal stop section |
- Fixing the section to the ceilingFix the track or the wide-flange section under the raw concrete slab using hammer-in anchors or suitable concrete screws, at a maximum spacing of 60 cm, inserting a resilient acoustic sealing strip.
- Cutting and inserting the studsCut the vertical C studs shorter by the foreseeable deflection plus a safety margin of 5 mm. Slot the studs into the top section without crimping or screwing them to the track, so as to preserve the sliding.
- Screwing the facings while leaving a clearanceStop the plasterboards at a distance from the slab corresponding to the required deflection. Screw the facings only to the vertical studs, stopping at least 50 mm below the track so as not to tie the partition to the ceiling.
- Finishing the top jointConceal the crushing gap with a plaster strip fixed to the slab but free in front of the partition, or form a finishing profile creating a sliding recessed joint with no plaster bond between the head and the slab.
A long-flange section or a sliding angle represents only a material extra cost of about two francs per linear metre compared with a conventional standard-track installation. This small difference in supply cost protects the partitions against differential movements of the structure and prevents generalised cracking at the partition head during the use of the building.
The pathology of crushing: from residual deflection to generalised cracking
When the structural work delivers a raw floor, the reinforced concrete slab has not finished deforming. Under the effect of plastic shrinkage, multi-year creep and the later application of dead loads (floating screeds, floor coverings, partitions and technical equipment), the residual deflection of a concrete slab increases over several months, even several years. If the lightweight plasterboard partition is fitted with a rigid connection to the underside of the floor, the metal framing system is unintentionally turned into a load-bearing element. Having no capacity to take axial load, the work is forced into compression.
The transmission of these vertical forces to the vertical studs crushes the dry structure immediately. As soon as the slab deflects by a few millimetres with no axial freedom, the vertical sections buckle under the stress. The plaster facing then undergoes shear and compressive stresses that it cannot absorb. The phenomenon first shows as a bulging deformation of the facings, followed by the mechanical pull-out of the through-fixing screws.
The direct consequence of this locking is generalised cracking at the partition head. This pathology is not limited to a micro-detachment at the ceiling edge: it produces continuous horizontal cracks ten or fifteen centimetres below the slab, stepped diagonal cracks starting from the upper corners of door frames, and complete bursting of the reinforced tape joints. In severe cases, the overpressure distorts the door frames to the point of preventing the leaves from closing and shears the embedded electrical conduits.
Diagnosing locking, remedial protocols and economic impact of the sliding track
Analysing a crushing failure requires a methodical check of the partition head. To identify the exact origin of the defects without carrying out unnecessary demolition, foremen and site managers compare the visual symptoms with recurring installation faults.
| Visual finding on the work | Identified execution defect | Corrective action required |
|---|---|---|
| Continuous horizontal crack under the ceiling angle | Board butting squarely against the slab with no provision | Horizontal sawing of the facing to create a head clearance of 15 to 20 mm |
| Partition bulging in the middle, studs bowed | Studs too long, cut tight and crimped into the top track | Partial removal of the facing, trimming of the studs, fitting of a slider |
| Localised bursting of the plaster along the top line | Through-screw fixed into the flange of the top section | Removal of the stray upper screws, redoing of the jointing tapes |
| Interior doors jamming and hairline cracks | Slab load transferred to the door-frame reinforcing sections | Freeing the heads of the reinforced tubular studs under the top lintel |
Financially, the cost gap is staggering. Fitting a telescopic head track with deep flanges or a specific sliding section represents a minimal extra material cost, often about two francs per linear metre compared with a standard angle or track. Conversely, the absence of this functional clearance, when defects appear on whole occupied floors, requires a heavy repair protocol carried out in the existing building.
- Cutting under the ceilingMake a horizontal plunge saw cut on both faces of the partition, 20 mm below the underside of the concrete slab, without damaging the web of the metal sections.
- Releasing the stray fixingsLocate and unscrew every fixing connecting the facing or the studs to the upper flange of the anchoring track.
- Fitting cover strips or add-on telescopic sectionsInstall a suitable stop section or a sliding angle fixed exclusively to the slab or to the partition, allowing free vertical movement with no rigid connection.
- Finishing repairsRedo the burst surface joints, sand and prepare the substrates to receive the subsequent finishing work by the painters.
For recent office and residential construction sites subject to SIA 242, the site manager must require, from the setting-out phase, verification of the civil engineer's calculation notes on the theoretical deflection. This check makes it possible to define the exact height of the sliding section flanges and to guarantee the definitive structural independence of the partition.
Crisis management on site: release protocol after crushing
When the residual deflection of a concrete slab acts on an assembly built rigid at the head, the finding is unmistakable: bulging of the metal studs, shearing of the fixings and generalised cracking at the partition head. This situation calls for urgent action to stop the transfer of loads from the structural work to the lightweight framing. As soon as defects appear over several bays, the site foreman must record the deformation in writing and request the civil engineer's level survey before any removal.
- Making safe and mechanical reliefStrip out the acrylic sealant and, with a plunge blade, saw a continuous horizontal strip of 20 to 30 mm in the facing at the top, on both sides of the partition. This cut immediately releases the compressive stress transmitted by the concrete.
- Trimming the metal studsCheck the vertical sections for buckling. Using tin snips or a nibbler, shorten the studs so as to restore the prescribed head clearance, without touching the tracks fixed to the underside of the floor.
- Reinstating the sliding according to SIA 242Fix guide angles or a specific sliding section to restore the sound insulation and the fire rating required by SIA 242, then conceal the slot with a sliding cover strip decoupled from the ceiling.
The cost of a sliding track and the proper head clearance is a trivial fraction of the budget per linear metre at initial installation. By contrast, the detachment of skirtings, the replacement of twisted studs, the redoing of facings and the repainting of entire floors reach disproportionate amounts, which fall on the contractor responsible for the locking under the slab.
Frequently asked questions
How do you size the free space above the plasterboards to absorb the movement?
The head clearance must match the residual deflection calculated by the civil engineer, plus a safety margin of at least 5 mm. According to SIA 242, a sliding gap of 15 to 25 mm is generally provided for usual spans. The boards and the vertical studs are cut shorter so as to slide freely in the top track without ever butting against the concrete.
Can the facing be screwed into the top section to stabilise the partition head?
No, this is the fundamental error that neutralises the sliding track. Self-drilling screws must pass only through the facing and the vertical studs, stopping without fail below the flange of the top section fixed to the structure. Screwing into the upper element mechanically ties the partition to the slab, which causes generalised cracking at the head from the first millimetres of floor deformation.
What are the first visual signs of a slab sinking onto a dry-lining partition?
Warning signs often appear before the top joint tears: abnormal rubbing at the top of interior doors, screw heads popping out under axial compression, or a slight horizontal bulge in the upper third of the wall. If action is delayed, the facings break and the studs buckle under the dead weight of the concrete transmitted to the tracks.
How do you guarantee fire-stopping while keeping a sliding clearance?
Fire resistance is maintained by inserting high-density rock wool strips or a certified fire-stopping bead into the empty space between the framing and the concrete. The partition keeps its freedom of vertical movement with no acoustic bridge or break in the thermal compartmentation. This specific installation prevents the spread of smoke while scrupulously meeting the requirements of SIA 242.
Texts and standards cited
- norme SIA 242Plastering, rendering, dry-lining and ceiling systems: decoupling requirements and management of structural movements
