Skip to content
Website
🧱 CFC 411Surface water: slope, drainage and infiltrationChapter 2 of 10 in the section

The drainage channel: position, width, load class and sinking grating

Installing a pedestrian-class drainage channel in a vehicular access ramp leads to immediate breakage of the grating and loosening of the body under axle loads. This chapter details the selection of load classes according to SIA 318 and VSS standards, as well as the pouring of the bedding concrete and lateral haunchings essential for the stability of the structure.

Key takeaways

  • A residential garage entrance requires at least a class B 125 grating according to standards.
  • The SIA 318 standard requires a rigid base to distribute dynamic rolling loads.
  • The lateral haunching concrete must rise along the channel body up to the required level.
  • The grating must systematically rest between three and five millimetres below the finished vehicular surfacing.

Select the load class to prevent breakage under car traffic

The mechanical sizing of a private road drainage channel allows for no approximation. The most costly mistake observed on external works construction sites consists of installing an entry-level modular channel, intended for simple pedestrian paths in a garden, in the turning circle or ramp of a private garage. The wheels of a light vehicle exert point pressure combined with horizontal shear forces during braking and acceleration phases. A lightweight grating made of folded sheet metal or plastic yields immediately, causing the slot to collapse and blocking rainwater drainage.

Channels and drainage devices integrated into traffic surfaces must withstand the traffic loads planned for the development area without settlement or inadmissible deformation.

Norme SIA 318
Allocation of resistance classes according to uses in external works
ClassTest loadPermitted scope of applicationTypical use case CFC 411
A 1515 kNSurfaces exclusively for pedestrians or cyclistsGround-level patios, garden paths, private footpaths
B 125125 kNTrafficable footpaths, private car parks, villa entrancesGarage access for passenger cars, light vans
C 250250 kNRoad kerbs, private delivery yardsMixed traffic lanes with occasional passage of municipal trucks
D 400400 kNHeavy traffic lanes, access roadsPrivate industrial areas, frequent heavy goods vehicle traffic

VSS road standards and the SIA 318 standard unambiguously define usage thresholds. Even for a detached house without permanent heavy traffic, class A 15 is formally excluded as soon as a wheel is likely to pass over it. At least class B 125 should be specified for private vehicular driveways, or even class C 250 when the access has a pronounced slope or requires turning manoeuvres on the spot, which are sources of violent shear forces on the fixing rebates.

Execute the concrete bedding and haunching in accordance with professional rules

The overall resistance of a modular channel depends half on the prefabricated product and half on its wedging mass. Placing linear elements on a bed of stabilised sand or simple laying gravel inevitably leads to punching and dislocation of the joints. The sub-base must be excavated beforehand, leveled with a bearing capacity complying with the subgrade requirements and compacted without subsidence.

Lateral channel haunching
Mass of concrete poured against the vertical sides of a channel to block the lateral thrusts of the neighbouring surfacing and transmit dynamic loads to the base.
  1. Excavation of the installation trenchOpen the excavation with a lateral extra width of at least fifteen centimetres on each side of the element to allow the placement of formwork or haunching.
  2. Pouring the bedding slabPlace a bed of concrete with a plastic consistency, of minimum class C20/25 or C25/30, at least ten to fifteen centimetres thick, compacted and leveled to a chalk line with the required invert slope.
  3. Alignment and interlocking of channelsPlace the elements directly into the fresh concrete of the slab. Interlock male-female joints using the manufacturer's seal, align with a straightedge and wedge with a rubber mallet while checking the level.
  4. Pouring vertical haunchingsConcrete the lateral flanks in the shape of a wedge or a straight cradle up to the lower edge of the paving or asphalt, keeping the gratings locked in their housing to prevent the body from pinching under the pressure of the fresh concrete.

Once the concrete haunching has hardened, the connection with the adjacent paving or flagging requires special attention. Direct rigid contact between the paver and the metal rebate of the channel must be avoided: the use of a flexible joint or a compressible polymer joint absorbs the thermal expansions of the external surfacing without transmitting destructive stresses to the bedding mass.

Hydraulic sizing and drainage cross-section according to the SIA 318 standard

The sizing of a linear collection line in private roads is not limited to mechanical resistance under axle traffic. In front of a garage threshold or at the low point of an access ramp, the absorption capacity of the grating and the gauge of the internal profile directly determine the protection of the structure against flooding. In accordance with the principles of the SIA 318 standard, the hydraulic calculation takes into account the local design rain intensity, the area of the connected catchment basin and the nature of the adjacent surfacing.

For a paved or asphalted access ramp with a descending slope of 5 to 15%, runoff water arrives at high speed at the channel line. A grating that is too narrow or whose free passage cross-section is obstructed by an unsuitable decorative pattern generates a springboard effect: the water jumps over the gully and infiltrates under the garage door. The choice of internal profile must offer sufficient drainage reserve to convey the instantaneous water volume to the underground connection points.

Selection criteria for channel bodies and gratings in external works
Site configurationUseful internal profileRecommended grating typeAbsorption capacity
Private vehicular ramp foot (> 8 %)Width 150 to 200 mm with integrated slopeDuctile iron with clip-on transverse slotsVery high, captures fast flow velocities
Flat individual garage entranceWidth 100 to 150 mm with flat bottomGalvanised steel grating or cast ironHigh, suitable for diffuse runoff
Permeable paved vehicular accessWidth 100 mm with low profileBridge grating or profiled slot gratingMedium, compensated by surface infiltration
Van or delivery manoeuvre areaReinforced width 200 mmSpheroidal graphite iron with lockingMaximum, secure passage cross-section

The outlet of the line requires the installation of an end piece or a channel foot gully equipped with a removable silt bucket. This receptacle intercepts sands, gravels and plant debris carried by torrential rains before they enter the property's drainage network. The connection to the buried collector must be made with a watertight elastomeric sleeve preventing any leakage into the subgrade of the road.

Altimetric setting, movement joints and connection with the surfacing

The stability of a channel line subject to rolling loads relies on the homogeneity of the complex formed by the bedding and haunching concrete. The prefabricated channel element does not provide any structural load-bearing function by itself; it constitutes the internal formwork and the support track for the grating. VSS standards recommend continuous lateral concreting rising up to the heel under the protection angle, guaranteeing complete encasement against horizontal thrusts transmitted by vehicles during turning manoeuvres.

  1. Setting out and alignment by chalk lineStretch an alignment chalk line representing the axis of the line and the theoretical invert line, strictly set 3 to 5 mm below the future finished edge of the adjacent surfacing.
  2. Pouring the bedding slabSpread a bed of semi-dry to plastic consistency concrete to the thickness defined by the load class of the grating, manually compacted on the prepared excavation form.
  3. Installation and interlocking of elementsPlace the channel bodies from downstream to upstream, with connection lips oriented in the direction of flow, tightening the seals provided by the manufacturer.
  4. Assembly of trapezoidal haunchingsConcrete the lateral cheeks symmetrically to prevent any lateral displacement of the sections, moderately vibrating the mix up to the lower edge of the grating support.
  5. Installation of movement jointsCreate transverse joints in the bedding and haunching concrete mass every 5 to 6 linear metres or in line with the expansion joints of adjacent slabs.

The contact between the haunching mass and road or pedestrian surfacings requires special care. When laying hot bituminous surfacing, the edge of the channel must be protected from compaction plant impacts. In the case of concrete or natural stone paving laid on a sand or gravel bed, the pavers bordering the angle must be mortar-bedded over a width of 100 mm to neutralise differential settlement and eliminate the risk of spalling under wheel loads.

Diagnosis of defects and repair of a faulty channel

The crushing of a channel as soon as the first vehicles pass almost systematically reveals two combined errors: the choice of a profile reserved for pedestrian areas and the absence of a continuous wedging mass. When a grating twists or the polymer concrete body bursts under wheels, the diagnosis must be immediate. Longitudinal cracking of the contiguous surfacing and tilting of the walls indicate flexural failure under point load. In this configuration, no surface repair is feasible. Trying to reseal a grating or patch a crushed rebate constitutes a technical waste of time.

  1. Complete removal and excavation base clearanceCleanly cut the surfacing with an angle grinder at least 20 centimetres from the flanks of the damaged channel. Remove debris and strip the unstable base down to the load-bearing ground or compacted granular foundation layer.
  2. Pouring the bedding layer and levellingPour a firm consistency bedding concrete at least 15 centimetres thick. Install new elements conforming to the required load class, with gratings locked in their frame, wedging the upper edge 3 to 5 millimetres below the finished level of the paving or asphalt according to the SIA 318 standard.
  3. Concreting haunchings and repairing edgesExecute the lateral concrete haunching of minimum class C20/25 or C25/30 over the full height of the flanks, in accordance with the recommendations of the VSS standards. Create a flexible, hydrocarbon-resistant joint between the encasement concrete and the final surfacing.

During the acceptance of the repaired work, the inspection focuses on the profile base, the stepless alignment and the proper water clearance towards the silt collection chamber. Access must remain closed to traffic during the complete hardening of the bedding and haunching concrete to avoid any premature impact.

Frequently asked questions

Why can a class B 125 grating break under a simple passenger car?

Class B 125 is designed for light static loads or car parks with very low speeds. In a ramped garage entrance, vehicles brake, turn their wheels on the spot or accelerate. These manoeuvres induce dynamic forces and axle point pressures that far exceed the capabilities of the grating. VSS standards recommend class C 250 as soon as regular car traffic manoeuvres on the structure.

What waiting period must be observed before allowing traffic on freshly concreted channels?

Even with a channel of suitable class, overall resistance relies entirely on its bedding mass and lateral haunchings. A minimum setting time of three to seven days, depending on the ambient temperature and the type of cement used, must be observed before authorising the passage of light vehicles. For the passage of delivery trucks or construction machinery, a twenty-eight-day curing period remains imperative to reach nominal bearing capacity.

How should the joint between the channel body and hot bituminous asphalt be treated?

Direct contact from a compaction roller on the edge of the channel breaks the cast iron edge or polymer concrete. The bituminous asphalt should be carefully compacted with a mechanical tamper along the haunching edge. Between the channel frame and the wearing course, a hot-poured bituminous jointing tape or an elastomeric sealing joint ensures rainwater tightness and absorbs thermal expansions without cracking.

Should channels with an integrated slope be installed or should the slope be created on the concrete invert?

On a flat surface such as a courtyard or a garage threshold without natural gradient, channels with a built-in bottom slope greatly facilitate water self-cleansing. When the ground already has a sufficient slope, a flat-bottomed channel set on a regular slab is perfectly suitable. The SIA 318 standard requires a minimum slope towards the outlet in all cases to prevent sludge stagnation.

Texts and standards cited

  • norme SIA 318External works: surface water drainage requirements, altimetric setting of channels and drainage slopes
  • normes VSSInstallation prescriptions for crowning and closure devices, load classes and execution rules for bedding masses

In the same section