Key takeaways
- Drip irrigation reduces foliar evaporation and concentrates the water supply directly at the root zone of the plants.
- JardinSuisse recommends dividing networks into zones according to exposure requirements and soil retention.
- The hygroscopic disc rain gauge mechanically interrupts the cycle as soon as the precipitation threshold is reached.
- The volumetric sensor measures available water and locks the controller as long as the soil reserve is sufficient.
Choosing between drip irrigation and sprinkler irrigation according to JardinSuisse recommendations
On external works construction sites subject to Swiss landscaping industry standards, the choice of distribution method depends directly on plant typology and surface configuration. Sprinkler irrigation, reserved for lawned areas and wildflower meadows, sprays droplets into the ambient air. This process generates considerable losses through wind drift and direct evaporation before the water reaches the ground, particularly on slopes exposed to the Foehn or the Joran. In contrast, for shrub beds, boundary hedges, perennials, and green roofs, the technical guidelines issued by JardinSuisse systematically recommend localized micro-irrigation in the form of tubes with integrated pressure-compensating drippers.
| Construction site criterion | Spray or rotor sprinkler irrigation | Pressure-compensating drip irrigation |
|---|---|---|
| Required operating pressure | 2.5 to 4.5 bar depending on nozzle throw | 1.0 to 2.5 bar with pressure reducer |
| Average water efficiency | 60 to 70% (losses due to wind and evaporation) | 90 to 95% (direct application to the root) |
| Average circuit flow rate | 800 to 2500 l/h per sprinkler zone | 150 to 600 l/h per 100 metres of line |
| Foliar health sensitivity | High (wetting promotes powdery mildew and rust) | None (foliage kept strictly dry) |
| Aesthetic integration | Buried pop-up sprinklers invisible at rest | Pipes hidden under organic or mineral mulch |
The installation of a drip system requires careful zoning in the distribution chamber. A low-density polyethylene pipe with a diameter of sixteen millimetres, featuring integrated drippers every thirty or thirty-three centimetres with a nominal unit flow rate of one point six or two point two litres per hour, must never be supplied directly from the distribution network pressure. The foreman systematically inserts a 120-mesh screen filter and a pressure regulator preset to 1.5 bar downstream of each 24-volt solenoid valve. Without this mechanical reduction, the pressure-compensating membranes expand abnormally, leading to disconnections of barbed fittings and uncontrollable water overconsumption.
Link programming to the rain gauge and soil moisture sensor
An electronic controller that triggers the opening of solenoid valves during a rain event constitutes a major technical anomaly, detrimental to the company's reputation and the client's operating costs. To ensure frugal water management, the control system must receive local physical information transmitted by two distinct and complementary cut-off devices: the mechanical hygroscopic disc rain gauge and the volumetric moisture sensor buried in the ground.
- Positioning and adjustment of the disc rain gaugeFix the rain sensor to a wall coping, fence post, or external gutter, completely clear of tree canopies and out of reach of sprinklers. Set the trigger ring to five or six millimetres of precipitation. As soon as the rain moistens the cork or synthetic polymer discs, they swell and open the dry contact connected to the controller's sensor terminals, instantly freezing the programmed cycles.
- Placement of the volumetric sensor in the root zoneDig a test pit in the most representative bed, in partial shade. Push the sensor measuring rods horizontally into undisturbed soil, at a depth between fifteen and twenty-five centimetres, where the active root system of the plants is concentrated. Gently compact the topsoil around the electrodes without creating any air pockets.
- Calibration of the cut-off threshold on the controllerConnect the sensor to the control unit. After a soaking watering followed by a twenty-four-hour drainage period, note the field capacity value displayed by the sensor. Define the watering prohibition threshold slightly above the temporary wilting point of the plant soil, so that the system only unlocks watering when the readily available reserve for the plant is truly depleted.
- Switch test and locking of time windowsManually check circuit opening by simulating sensor saturation. Program watering start times exclusively between three o'clock and six o'clock in the morning, when distribution network pressure is optimal and evaporation minimal, while ensuring the controller displays the suspension icon as soon as either sensor indicates sufficient moisture.
Acceptance of the work imperatively includes handing over the zone layout diagram and adjustment sheets to the client. During winterisation operations before the first frosts of November on the Swiss Plateau, the foreman purges the drip lines with a compressed air compressor set to a maximum of two bar, disassembles frost-sensitive sensors if required by the manufacturer, and switches the controller to the complete stop position while keeping backup batteries active.
Root distribution and technical comparison between drip irrigation and sprinkler irrigation
According to the rules of the trade issued by JardinSuisse, water distribution on a plot must strictly adapt to plant typology and soil infiltration speed. Sprinkler irrigation using spray heads or rotors remains essential for lawns and wildflower meadows, as it ensures homogeneous coverage over large open areas. In contrast, sprinkler irrigation on perennial beds, hedges, and shrubs is a major source of waste: the umbrella effect of the foliage deflects drops out of root reach, wind disperses the spray onto hard surfaces, and direct evaporation under the effect of ambient air dissipates a significant portion of the water even before it contacts the ground.
| Technical parameter | Surface drip irrigation under mulch | Spray or rotor sprinkler irrigation |
|---|---|---|
| Required operating pressure | 1.0 to 2.5 bar (requires a pressure reducer) | 2.5 to 4.5 bar (depending on nozzle throw) |
| Average hourly precipitation rate | 2 to 4 litres per hour per dripper | 15 to 45 millimetres per hour on the surface |
| Evaporation and drift losses | Less than 5% under plant or mineral mulch | 20 to 35% in hot weather or moderate wind |
| Recommended plant target | Hedges, shrub beds, perennials, street trees | Ornamental lawns, sports turfs, dense ground covers |
| Sensitivity to soil compaction | None: slow supply respects surface structure | High: risk of soil crusting and runoff on silty soil |
For shrub beds and hedges, the drip network is laid out using low-density polyethylene pipes of sixteen millimetres diameter, featuring turbulent pressure-compensating integrated drippers spaced thirty to fifty centimetres apart. The line is unrolled at the base of the plants, firmly anchored in the ground every metre using metal or polymer staples to prevent any movement under thermal pressure, and then covered with a layer of wood chips or mineral mulch. This covering protects the polyethylene against ultraviolet rays and completely blocks direct evaporation from the deep wetted bulb.
Regulation control: installation of the rain gauge and soil sensor
Programming a fixed schedule without climatic control turns a modern installation into a source of financial waste. To prevent solenoid valves from triggering during or after a shower, connecting a mechanical hygroscopic disc rain gauge or an electronic tipping bucket sensor to the central unit's dedicated input is mandatory. The device cuts the 24-volt low-voltage circuit via a dry contact as soon as a defined water height, commonly set between three and six millimetres of precipitation, moistens the expanding discs.
The location of the rain gauge determines the accuracy of the information transmitted to the controller. It must be fixed to an unshakeable vertical support, such as a fence post, a technical mast, or an unobstructed eaves overhang, strictly in the open air. Its reception cone must be placed out of reach of the jet of neighbouring oscillating sprinklers and away from tree canopies, to avoid late dripping drops that distort system reactivation.
While the rain gauge manages immediate stoppage in the face of overhead weather, the soil moisture sensor regulates watering frequency according to water actually accessible to the roots. Tensiometric or capacitive sensors measure the electrical resistance or dielectric permittivity of the substrate. The sensor is inserted vertically or at a forty-five-degree angle into the active root zone, generally between fifteen and twenty-five centimetres deep for shrubs. The landscaper creates a pre-hole with a manual auger to the exact diameter of the sensor, then re-inserts site fine soil slurry to ensure direct contact without air pockets along the electrodes.
Regarding construction site interfaces, the landscape constructor intervenes strictly downstream of the general isolation valve and the backflow preventer device. The drinking water supply, meter sizing, and protection against backflow to the public network fall under the sanitary installations trade (CFC 250). Immediately downstream from this delivery point, the external works team installs the solenoid valve manifold in a drained technical chamber, installs the 120-mesh disc filter essential to protect drippers from any clogging, pulls the remote control cables, and calibrates the programming to split inputs into several short cycles to promote deep infiltration.
Diagnosis and fault management on a controlled network
A malfunction on a controlled drip irrigation network usually results in two critical anomalies: irrigation during a rain event or hidden drying of a planted sector. These incidents rarely stem from massive material breakage, but rather from a failure in information transmission between sensors and the control unit, or mechanical drift on regulation components.
- Checking a solenoid valve stuck openA solenoid valve that no longer closes despite the shut-off command indicates an internal obstruction. Unscrew the valve cap, inspect the nitrile diaphragm, and clear the discharge port often clogged with a grain of sand. Clean the plunger core of the solenoid.
- Detection of clogging on the drip networkDry soil at the base of beds despite a validated cycle indicates abnormal pressure drop or clogging of pressure-compensating drippers. Measure pressure with a pressure gauge at the end of the line. If pressure is zero, clean the upstream filter screen or check the set regulator.
- Recalibrating or repositioning the soil sensorA moisture sensor that constantly blocks cycles without valid reason has often lost its direct contact with the topsoil. Remove the housing, rehydrate the installation area, and reinsert the rod without leaving an air pocket along the sensor.
In accordance with JardinSuisse professional guidelines and water management rules, each troubleshooting intervention must conclude with a manual zone-by-zone test, coupled with flushing the branch lines to remove mineral deposits.
Frequently asked questions
How to check on site that a hygroscopic disc rain gauge triggers correctly?
Switch the controller to manual mode on a test valve. Press the mechanical test stem located at the top of the rain gauge housing. Watering must stop within a few seconds if the dry contact is working. If there is no shut-off, check the wiring on the controller's dedicated terminals or replace the set of compressed cork washers saturated with impurities that no longer swell properly upon contact with moisture.
Why do drippers continue to ooze at low points after the complete stop of the cycle?
This continuous oozing is not a solenoid valve leak but the gravity drainage phenomenon of the pipe towards the lowest points of the terrain. Residual water escapes through the lower orifices as long as the branch line contains air. To eliminate this waste and prevent saturation at the base of plants, install drippers equipped with a calibrated anti-drain valve that close automatically as soon as pressure drops.
At what exact depth should the moisture sensor be installed to protect a shrub bed?
The sensor must be placed directly in the active root zone, i.e., between fifteen and twenty-five centimetres below the finished surface for shrubs. Installation that is too shallow distorts the reading by reacting to the first ray of sunshine, while installation that is too deep blocks irrigation while the upper layer has already dried out. Lightly compact the earth around the element to ensure perfect hydraulic continuity without damaging the cable.
What technical operation guarantees the protection of the regulation system before the Swiss winter?
Complete drainage using low-pressure compressed air remains essential before the first frosts. Isolate the main valve, connect a construction site compressor to the manifold and blow out each line individually under moderate maximum pressure. Remove frost-sensitive soil sensors if recommended by the manufacturer, remove the alkaline battery from the control unit, and disconnect the general power supply to prevent winter voltage surges.
Texts and standards cited
- norme SIA 118General conditions for the execution of construction work, governing rights, obligations, and acceptance of works between client and contractor.
