Skip to content
Website
🧱 CFC 411Paving and slabs: laying, joints and kerbsChapter 3 of 10 in the section

Joints: width, jointing sand, vibration, and the joint that never fills

Laying pavers edge-to-edge guarantees edge spalling from the very first vehicle manoeuvres. This chapter details the joint dimensioning rules according to the SIA 318 standard, the mechanical role of the jointing sand in locking the pavers, as well as the vibration method and the essential second filling pass after settlement.

Key takeaways

  • A minimum joint width guarantees load transmission without direct contact between edges.
  • The SIA 318 standard specifies joints calibrated according to the dimensional tolerance of the selected materials.
  • Crushed jointing sand infiltrates dry and is then compacted using a plate compactor with a protective pad.
  • Topping up the gaps after a few weeks compensates for the inevitable settlement of the jointing material.

Joint width and load distribution according to the SIA 318 standard

On a vehicular or pedestrian external works area, a paver never works alone. The overall stability of the surfacing depends entirely on the arching effect and lateral friction transmitted from one element to the next by the jointing material. When a pavier tries to tight-joint blocks without leaving a gap, under the pretext of achieving a finer line or hiding alignment discrepancies, the mechanical result is disastrous. As soon as an axle brakes or turns on the surface, the pavers tilt microscopically. Without an intermediate granular cushion to absorb these shear thrusts, the upper faces come into direct contact: the concrete or natural stone shatters immediately at the edges.

Recommended joint widths according to the type of paving
Type of paving elementMinimum spacingAverage target widthPermitted tolerance
Sharp-edged concrete paver3 mm4 to 5 mm± 1 mm
Standard chamfered concrete paver3 mm3 to 5 mm± 1.5 mm
Sawn natural stone paver4 mm5 to 8 mm± 2 mm
Split or natural cleaved paver6 mm8 to 12 mm± 3 mm

The SIA 318 standard governs tolerances and the execution of external floor surfacings laid on a flexible bed. It requires adapting the joint thickness to the manufacturing irregularities inherent to the material. Cleaved natural stone elements require more generous voids than factory-prefabricated products, because the geometric variations from block to block absorb a significant portion of the interval. Reducing the joint under the pretext of saving filling aggregate makes gravity flow of the sand down to the bottom of the slot impossible, leaving the base of the paver without lateral contact.

Jointing sand, mechanical compaction, and top-up after commissioning

Jointing for flexible paving tolerates no rounded, alluvial, or clayey material. It is mandatory to use a hard, angular, washed crushed sand with a granularity suited to the width of the interstices, generally zero-two or zero-four millimetres without excess ultra-fine dust. The angular grains interlock under lateral thrust to create genuine wedging through internal friction. Rounded sand from a gravel pit would roll under a wheel like a ball bearing, promoting the washout of joints by rainwater or street sweeping.

  1. Spreading and dry sweepingThe jointing sand must be perfectly dry at the time of application. It is poured onto the surface and brushed diagonally relative to the direction of the joint lines until the slots are visibly saturated.
  2. Preliminary surface cleaningBefore any vibrating machine passes over, any excess aggregate is carefully swept away. Residual grains trapped under the vibrating plate would irretrievably scratch the exposed face of the slabs or pavers.
  3. Vibration with a neoprene padCompaction is carried out using a plate compactor equipped with a polyurethane or neoprene soleplate. The vibration forces the jointing material downwards while bedding the paver into its laying bed.
  4. Second immediate filling passThe initial tightening causes an immediate drop in the sand level of twenty to forty percent. Sand is immediately re-spread to fill this void before opening to traffic.

The life of a paving does not end when the construction site crew leaves. Even after rigorous vibration, rain, surface runoff, and heavy traffic progressively compact the jointing during the first few weeks of operation. If the joints remain hollow a few millimetres below the edge, the sides of the paver lose mutual support in their upper third. Site management must plan a topping-up intervention scheduled three to six weeks after opening the surface. Dry sand is then brushed in again to restore the filling flush with the chamfer.

Diagnosis of the recalcitrant joint: refusal to penetrate and unsuitable gradings

On private roadworks and landscaped external works sites, the phenomenon of the joint refusing to fill almost systematically indicates a discrepancy between the actual geometry of the interstice and the physical characteristics of the chosen aggregate. When jointing sand remains blocked on the surface without migrating homogeneously down to the laying bed, the immediate risk lies in the appearance of underlying air pockets. As soon as vehicles are put into circulation, the absence of lateral shear force transmission leads to localized tilting of the pavers and systematic spalling of the upper edges, cancelling out the grip and durability criteria set by the SIA 318 standard.

Granular bridging
Premature mechanical locking of angular grains at the upper constriction of the joint. This phenomenon creates an artificial arch on the surface that prevents the make-up material from descending towards the bedding, maintaining a critical structural void beneath the facing.
Suitability of jointing aggregates according to joint opening
Nominal joint widthRecommended grading curveSweeping behaviourRisk of filling failure
2 to 3 mm (concrete pavers with lugs)Washed crushed sand 0/2 mmFluid penetration only on a perfectly dry materialGrain bridging from 5% moisture or presence of elements > 2 mm
4 to 6 mm (cleaved natural stone pavers)Crushed sand 0/4 mm or chippings 1/3 mmRapid descent under cross-sweeping and vibration passesSegregation if the mix contains too many fines below 0.063 mm
7 to 10 mm (irregular formats and old pavers)Crushed chippings 2/4 mm or clean 1/3 mm mixEasy filling by gravity assisted with a road sweeper's broomImmediate unblocking under the action of a vacuum road sweeper

The triggering factor for premature blockage lies almost exclusively in the moisture state of the material during installation. Jointing sand supplied or stored without a waterproof tarpaulin accumulates capillary water in rainy weather. This moisture induces apparent cohesion: particles agglomerate into compact clumps and refuse to slide along the rough walls of the pavers. Repeated passes with a broom then merely crush a surface crust without filling the useful thickness. Furthermore, the erroneous use of rounded alluvial sand, although very fluid when brushed, is prohibited because the absence of crushed edges prevents the self-locking of pavers under braking stress.

Vibration protocol, residual settlement, and scheduled top-up

Laying and initial sanding never definitively stabilize surfacing laid on a sand or gravel bed. Under the repeated action of vehicular traffic, precipitation, and the spatial reorganization of grains, the jointing sand undergoes inevitable mechanical volumetric settlement. When the upper level of the joint drops more than five millimetres below the edge of the paver, direct contact between adjacent pavers occurs during acceleration and turning phases. This rigid contact instantly breaks the edges by spalling. To comply with the SIA 318 standard, the joint plan must remain filled up to the bottom of the chamfer.

  1. Methodical vibration on clean pavingPass the plate compactor equipped with a polyurethane or neoprene pad over paving swept to refusal. The surface must be cleared of any excess aggregate to avoid embedding chippings into the upper faces under the impact.
  2. Regulated watering and foundation consolidationWater in a fine spray without washing out the slots to encourage the evacuation of interstitial air and the descent of the aggregate, then immediately carry out a new application of 0/2 mm crushed sand brushed to refusal.
  3. Densification period under service loadPut the section into normal circulation for at least one month. The oscillations caused by wheels settle the laying bed and lock the jointing grains into their final arrangement.
  4. Second top-up campaign and finishingCarry out the contractual top-up: spread extra-dry crushed sand, sweep diagonally relative to the joints until complete saturation, then clean the surface without vacuuming the material in place.

Remediation of spalling and repair protocol for defective joints

When paver edges shatter under traffic, the diagnosis is unequivocal: the elements were laid in direct contact without respecting the minimum interstice prescribed by the SIA 318 standard, or the jointing was not carried out to refusal. Horizontal braking and shearing stresses are no longer transmitted by sandy friction on the flanks, but by point-to-point edge-to-edge crushing. At this stage, the damage is irreversible for the spalled pieces, which must be extracted and replaced.

  1. Purging and cleaning of voidsExtract clogged or poorly distributed surface jointing to a depth of at least 30 mm using a compressed air lance or a high-pressure cleaner equipped with a flat nozzle, at a shallow angle so as not to destabilize the laying bed.
  2. Replacement of broken elementsRemove pavers with chipped edges using specific paver pliers. Locally repair the granular laying bed, replace new elements while respecting the spacing required by the SIA 318 standard according to the type of paver.
  3. Refilling to refusal by cross-sweepingSpread dry crushed sand with a particle size of 0/2 mm or 0/4 mm depending on the joint width. Sweep diagonally relative to the laying lines to force the gravitational fall of the aggregate to the bottom.
  4. Vibration and contractual top-upPass the plate compactor equipped with its elastomer soleplate to make the sand descend under controlled vibration. Repeat the spreading, leave a slight protective surplus, and schedule the second top-up intervention after a few weeks of settlement under traffic.

Re-setting a joint that refuses to fill requires adapting the grading cut: if the joint measures less than 3 mm, switching to de-dusted 0.3/1.2 mm or 0/1 mm quartz sand resolves the jamming without weakening the surface mechanical bond.

Frequently asked questions

Why do the edges of my concrete pavers shatter after a few weeks of rolling traffic?

Spalling results from direct contact between elements. Without a joint width conforming to the SIA 318 standard, or in the presence of an insufficiently filled joint, the shear forces generated by vehicles are not distributed over the entire height of the flanks. The concentration of loads on the upper edges pulverizes the concrete. Replacement of degraded parts with complete re-jointing is required.

How to treat a joint that does not fill despite repeated sweeper passes?

The problem generally stems from aggregate that is too coarse for the interstice or wet material creating a mechanical bridge. Suspend the operation, dry the surface, and replace the jointing sand with a finer cut, for example washed crushed 0/2 mm or rounded 0.5/1.5 mm sand. Light mechanical plate vibration with a synthetic soleplate triggers the necessary collapse of the material into the void.

Is the second joint top-up after a few weeks contractually owed by the landscaper?

Yes, this operation is an integral part of professional practice according to the SIA 318 standard for modular surfacings laid on an unbound granular bed. Under the combined action of precipitation and rolling loads, the bedding material naturally compacts by 15 to 25%. The contractor must plan and log this second jointing in their quotation to guarantee the definitive durability of the delivered work.

Can high-pressure cleaning be authorized on newly handed-over paving?

High-pressure stripping as well as industrial vacuum sweepers must be formally prohibited during the first six months of operation. These machines vacuum or dislodge sand from joints that are not yet stabilized, causing structural de-cohesion of the blocks. Initial maintenance must be limited to gentle dry manual sweeping or very low-pressure watering without a rotating nozzle.

Texts and standards cited

  • SIA 318External works: dimensioning, laying, jointing, and compaction requirements for modular concrete and natural stone surfacings.

In the same section