Skip to content
Website
🧱 CFC 411Low walls, retaining structures and external stairsChapter 4 of 10 in the section

The foundation: frost depth, strip footing, minimum reinforcement and cracked wall

This guide details how to determine the frost depth for low external walls in external works in Western Switzerland. You will learn how to set out the excavation according to the plot altitude, prevent frost heave beneath the base and cast a stable reinforced concrete distribution footing, in accordance with the practical requirements of standard SIA 318.

Key takeaways

  • A frost-free base goes from eighty centimetres on the Swiss Plateau to over a metre at higher altitudes.
  • Frozen water forms ice lenses beneath the footing and breaks unreinforced masonry.
  • The distribution footing distributes the wall load over a sound and stable excavation base.
  • The rear drainage discharges water before it can infiltrate beneath the foundation concrete.

Determine the frost-free clearance according to altitude and soil conditions

In Western Switzerland, the stability of a low retaining wall or fence wall depends primarily on the embedment of its base. When a footing rests flush with the ground or at a shallow depth, winter frost penetrates beneath the concrete. In frost-susceptible soils such as moraine silts, clays or very fine sands, pore water migrates by capillarity toward the freezing front. It forms ice lenses that increase in volume and exert considerable vertical pressure. This frost heave of the soil is never uniform: part of the wall rises by several centimetres while the rest remains fixed, causing through-cracks, joint shearing or irreversible tilting of the structure upon thawing.

Indicative frost-free embedment depths according to sector and altitude in Western Switzerland
Geographical sectorConstruction site altitudeDominant soil natureRecommended minimum depth
Lake Geneva basin and Rhône plainLess than 500 mSandy silt or clayey gravel80 cm
Swiss Plateau (Vaud, Fribourg)Between 500 and 800 mCompact moraine, weathered molasse90 to 100 cm
Jura foothills and Vaud AlpsBetween 800 and 1100 mFlint clay, calcareous silt100 to 120 cm
Jura valleys and alpine resortsMore than 1100 mHeterogeneous slope soils, scree120 to 150 cm

To validate the frost-free clearance, measurement is always taken from the lowest finished external ground level to the laying plane of the footing. On a sloping site, the classic mistake consists in aligning the excavation bottom with the upper terrain without checking the downslope side. If the downslope soil lies forty centimetres lower, the frost front will penetrate laterally beneath the foundation. It is therefore necessary to create successive steps to guarantee the protective earth thickness required by standard SIA 318 at all points.

Excavate the foundation pit and cast the distribution footing according to standard SIA 318

The primary function of the distribution footing is to absorb asymmetrical forces and uniformly distribute loads onto the foundation soil. In external works governed by standard SIA 318, it prevents differential movements of the subsoil from breaking the elevation, whether it is a wall made of concrete blocks, light riprap or dressed stone. Execution requires a rigorous method, from cleaning the excavation bottom to placing the reinforcement.

  1. Earthwork and mechanical cleaningOpen the trench with a grading bucket down to the defined frost-free level. Remove topsoil and pockets of inconsistent spoil until reaching sound, undisturbed ground.
  2. Placement of blinding concretePromptly cast a lean blinding concrete layer five centimetres thick. This layer protects the foundation base against construction site rain and drying out.
  3. Connecting reinforcement and positioningPosition a minimum reinforcement cage comprising continuous longitudinal bars connected by stirrups. Place the reinforcement on spacer blocks to prevent any contact with the ground.
  4. Concreting and vibration of the footingPlace structural concrete compliant with external exposure classes. Mechanically vibrate using a poker vibrator to eliminate air bubbles and completely embed the steel bars.

Mechanism of frost heave and failure of low walls

When a concrete or stabilised gravel distribution footing is cast at an insufficient depth, the water present in the pore soil changes state under the action of the descending freezing front. This phenomenon is not limited to the 9% volumetric expansion of freezing water. In fine or silty soils frequently encountered on the Swiss Plateau, capillary suction continuously feeds the freezing front from the water table or underlying layers. Pure ice lenses form directly beneath the support plane of the foundation, exerting considerable vertical pressures capable of easily overcoming the self-weight of a garden wall or low retaining wall.

The major problem with this movement lies in its heterogeneity. A wall footing never rises in a perfectly uniform manner along its entire length. Sunlight on one side of the masonry, the proximity of a hedge absorbing water or the varying permeability of the foundation soil create asymmetrical frost heave. Landscaping masonry—whether stacked concrete blocks, light riprap or mortared rubble walls—then works in simple bending or undergoes shear forces for which it possesses no inherent mechanical resistance.

From the first severe frosts of January, the stresses cause characteristic defects: stair-step cracking along the mortar joints, vertical shearing at one-third of the wall lengths, or separation of the footing. During the spring thaw, the ice melts rapidly without the released water being able to immediately infiltrate into soil that is still frozen deep down. The foundation soil temporarily turns into mud with no bearing capacity, leading to irregular residual settlements. The wall never returns to its initial position and accumulates increasing leaning over successive winters.

Frost depth according to altitude and reinforcement provisions

In Western Switzerland, determining the frost depth according to the region depends directly on the altimetric map, local topography and the susceptibility of the soil to frost. On the shores of Lake Geneva and the lower part of the Canton of Geneva, frost rarely penetrates beyond 80 cm during reference winters. On the other hand, as soon as the construction site rises onto the Fribourg plateaus, the Vaud Jura or the alpine valley floors of Valais, frost-susceptible layers commonly reach depths of 100 to 130 cm. Any durable landscaping requires adjusting the excavation depth according to this climatic reality.

Indicative frost-free embedment values and foundation provisions for garden walls in Switzerland
Geographical zone and altitudeMinimum frost-free clearanceDominant soil natureProvisions for the footing
Lake Geneva basin, Geneva, Rhône plain (< 500 m)80 cmAlluvium, sandy gravelC16/20 blinding concrete, continuous strip footing with continuous longitudinal reinforcement
Swiss Plateau, Jorat, Gros-de-Vaud (500 to 800 m)90 to 100 cmClayey moraines, fine siltsDrained non-frost-susceptible 0/32 gravel cushion, C25/30 reinforced concrete footing
Jura foothills, Vaud and Fribourg Prealps (800 to 1100 m)100 to 120 cmMarls, residual moraine siltsRemoval of fines, separation geotextile, peripheral frost-free toe
Upper Jura, alpine valleys (> 1100 m)120 to 140 cmHeterogeneous soils, silty screeDeep excavation, mandatory gravity drainage at the foot of the footing

To absorb slight permissible variations and prevent cracking of light superstructures, the distribution footing must receive minimum longitudinal tie reinforcement. Two continuous reinforcing bars with a minimum diameter of ten millimetres, tied to stirrups or U-bars every fifty centimetres, are generally sufficient to tie together the foundation of a low boundary wall or landscaping retaining wall. Reinforcement laps at corners and ends must comply with at least fifty times the nominal bar diameter.

Finally, the footing must imperatively include transverse contraction joints every five to eight linear metres maximum, as well as at each change in altimetric level or soil type. These joints prevent mechanical stresses due to concrete shrinkage and winter micro-movements from turning into random fractures across the masonry facing. Combined with clean well-graded aggregate backfill against the rear face of the wall, this design compliant with standard SIA 318 ensures the full stability of the structure against the most severe winter stresses.

Frost damage: diagnosis, underpinning and corrective measures

During snowmelt and spring thaw, a poorly founded low wall quickly highlights the effects of soil frost heave. When the distribution footing has been installed at an insufficient depth relative to the cantonal climate, the ice lenses formed beneath the structure melt asymmetrically. The ground abruptly loses its bearing capacity, leading to differential settlement. The mason or landscaper observes stair-step cracks along the joints, frank breakage of unreinforced concrete or forward tilting of the facing.

  1. Diagnosis and verification of the foundation levelCarry out an inspection trench against the facing to measure the actual depth of the footing relative to the finished ground. Check whether the excavation bottom rests on silts or frost-susceptible clays, which are highly sensitive to capillary rise.
  2. Underpinning using alternating baysTemporarily shore up the wall if its balance is precarious. Carry out earthworks beneath the old distribution footing in passes not exceeding one metre in length. Cast blinding concrete followed by lean leveling concrete down to the frost-free depth in accordance with standard SIA 318.
  3. Backfill replacement and hydraulic remediationExcavate frost-susceptible materials behind the wall. Install a drainage mass made of clean, non-frost-susceptible gravel wrapped in a non-woven geotextile, then lay an agricultural drain or slotted rigid pipe connected to a compliant outlet.

If the structure exhibits an out-of-plumb exceeding the tolerances of standard SIA 318 or complete shearing of the masonry, total demolition with reconstruction of the foundation remains the only durable option. The landscaper must then excavate down to sound, non-frost-susceptible ground, adapt the level according to local altitude and ensure continuous longitudinal reinforcement in the new footing.

Frequently asked questions

How to stabilise a boundary wall whose foundation is only 40 centimetres from the ground?

At this shallow depth, soil frost heave inevitably dislocates the structure from the first prolonged frosts in the plains of Western Switzerland. If the wall shows no major defects, one solution consists in carrying out underpinning using alternating one-metre bays to lower the base below the frost depth. Alternatively, installing peripheral horizontal thermal insulation using extruded polystyrene panels can slow down the penetration of cold.

What frost depth should be applied on the Swiss Plateau compared to the Jura or the Prealps?

On the Swiss Plateau, below six hundred metres of altitude, the minimum embedment depth of the footing is generally set at eighty centimetres according to standard SIA 318. In the Jura or prealpine zone, between eight hundred and one thousand two hundred metres, frost penetrates much deeper: the base must then be lowered between one metre and one metre twenty to guarantee the stability of the distribution footing.

Why does clayey soil accentuate frost damage on unreinforced footings?

Fine soils such as silts and clays retain water by capillarity. During winter, the freezing front draws this residual moisture upward, creating ice lenses that increase the soil volume by up to ten percent. This asymmetrical vertical thrust exerts bending stresses that unreinforced concrete cannot withstand, causing sharp wall failures from the very first freeze-thaw cycles.

Can a shallow foundation be compensated by a bed of draining gravel beneath the footing?

Yes, the thickness of a well-compacted non-frost-susceptible gravel foundation layer adds to the footing thickness to achieve the required frost-free clearance. If the standard prescribes eighty centimetres of protection, a thirty-centimetre distribution footing can be cast over fifty centimetres of compacted gravel with water drainage. This frost-insensitive material prevents water accumulation and eliminates the formation of lenses beneath the structure's base.

Texts and standards cited

  • SIA 318External works

In the same section