Skip to content
Website
🧱 CFC 411Paving and slabs: laying, joints and kerbsChapter 1 of 10 in the section

The bedding layer: thickness, particle size, uncompacted state, and the resulting rutting

After this chapter, you will know how to dimension and precisely set the thickness of a paving bedding layer in accordance with standard SIA 318. You will select the appropriate particle size envelope without fines to guarantee drainage, level the uncompacted material using a screed rail, and prevent any differential settlement or premature rutting under repeated vehicle traffic.

Key takeaways

  • The leveled bedding layer must never exceed the specified thickness after final compaction.
  • Excessive thickness inevitably causes differential settlement under vehicle wheels.
  • The crushed bedding material must be strictly free of fines to drain water effectively.
  • Final flatness depends on a foundation layer leveled to a strict millimetric tolerance.

Exact thickness and the categorical refusal to compensate for the foundation

On private road and external works construction sites, a frequent error consists in using the bedding layer to make up for flatness defects in the foundation layer. This practice is strictly contrary to standard trade practice. Standard SIA 318 specifies the requirements for paved and slab-covered surfaces: the thickness of the bedding layer after compaction must imperatively be between 30 mm and 50 mm, with the operational ideal set at a constant 30 or 40 mm. Under no circumstances does this layer constitute a structural leveling layer. If the foundation gravel shows hollows of several centimeters, the bedding layer will be thicker locally, which initiates the future degradation of the structure under vehicular traffic.

The bedding layer is screeded off using metal guides, without any pre-compaction. It must remain loose until the pavers are fully laid. Compaction is carried out exclusively during final tamping with a vibrating plate equipped with an elastomer soleplate, after the first joint sanding. During this tamping, the elements sink uniformly into the loose chippings. If the initial thickness varies from 30 mm in one place to 70 mm in another to mask a low point in the subgrade, the residual bulking coefficient will lead to completely divergent behavior under mechanical traffic loads.

To guarantee the regularity of the bedding layer, the surface of the underlying foundation layer must present a very strict leveling tolerance, in the order of plus or minus 10 mm under a 4-meter straightedge. It is on this accepted surface, free of puddles or segregation, that the screeding guides are placed. Generally, a loose screeding extra thickness of 5 to 10 mm is applied relative to the projected finished level, so that final tamping brings the top edge of the pavers exactly to the height of the concrete edgings and thresholds.

Particle size without fines and rutting mechanism under traffic

The aggregate choice conditions both the stability of the base and the drainage of infiltration water. According to standard SIA 318, the material used for the bedding layer must be clean crushed chippings, stable against water and frost, featuring a gap-graded or dense particle size curve. The most common standardized fractions in French-speaking Switzerland are 2/4 mm or 4/8 mm, or even 1/3 mm for clay pavers or concrete pavers with narrow joints. The use of all-in-one sands containing fine particles smaller than 0.063 mm is prohibited for permeable and draining laying.

Standard particle sizes for bedding layers according to loading conditions
Granular fractionType of laid elementsMain application areaCompaction behavior
Crushed chippings 2/4 mmStandard concrete and natural stone paversTerraces, private driveways, car accessExcellent wedging, low lateral displacement
Crushed chippings 4/8 mmLarge-format slabs and thick paversAreas with regular traffic, utility parkingMaximum permeability, high stability
Crushed sand 1/3 mmThin pavers or narrow clinkersStrict pedestrian traffic, covered terracesFine tightening, increased sensitivity to fines

Rutting results from differential settlement under rolling loads. When an axle crosses a paved surface, the vertical load is transmitted to adjacent pavers through friction in the joints, then distributed across the bedding layer and foundation. If the bedding layer is too thick, the edges of the crushed aggregate rearrange themselves under repeated shear cycles; the material slides laterally within the thickness of the layer because it is not confined like a bound base. This mechanical creep phenomenon carves two longitudinal ruts aligned with the vehicle wheel tracks.

Differential settlement under rolling load
Uneven sinking of the paved surface caused by the compression or lateral displacement of an oversized bedding layer, under the repeated action of concentrated wheel loads.

The presence of fines abruptly accentuates this degradation. In the event of precipitation, water infiltrates through the joints and stagnates on the foundation if the latter has low permeability. In the presence of clays or crushing dust, the bedding layer turns into slurry under the pumping effect exerted by vehicle wheels. The fine particles rise into the joints under hydrodynamic pressure, emptying the base layer of its solid matter. The paver loses its flat support, tilts under the wheels, spalls at its edges, and sinks into the rut.

Screeding on guides and maintaining the loose bed before laying

On a private road or vehicular access construction site, the temptation to compact the chippings before laying the pavers represents a common methodological error. The bedding layer must under no circumstances undergo preliminary compaction. Its primary function is to provide a loose and perfectly regular bed, capable of absorbing the geometric tolerances inherent to concrete or natural stone pavers during final tightening. Any preliminary tamping creates heterogeneous bearing zones that distort the bed levels and prevent the controlled sinking of the elements.

To guarantee the prescribed thickness, the execution method relies on the placement of rigid metal guides. The crew places square steel tubes or 30 to 40 mm flat irons directly on the previously accepted foundation layer. These reference rails are shimmed to the millimeter according to the required cross slope. The crushed material is dumped with a shovel or mini-excavator without driving over the prepared area, then screeded with a bevelled aluminum straightedge by pulling towards oneself in a straight movement.

Behavior of bedding layer mixtures under mechanical loading
Material and granularityFines (< 0.063 mm)Compaction behaviorRisk under rolling load
Crushed chippings 2/4 mmLess than 1% (washed)Rapid angular interlocking, predictable settlement of 5 to 10 mmOptimal: excellent resistance to lateral shear
Crushed chippings 2/5 or 1/3 mmLess than 2%High granular stability after joint tighteningLow: drainage maintained, stability under light axle
Rounded river gravel 2/4 mmPractically zeroAbsence of edge effect, continuous rolling of grainsCritical: immediate rutting due to granular slip
All-in-one sand 0/4 mmMore than 5%False wet tightening, total loss of saturated bearing capacityMajor: mud pumping to the surface and plastic settlement

Final vibration, granular tightening, and rut prevention

The stability of a paved surface under vehicles does not come from the intrinsic strength of the bedding layer, but from the three-dimensional mechanical interlocking between the pavers, the full joints, and the upper layer of the bed. As soon as the elements are laid progressively from the already leveled surface, the joints must be immediately filled to refusal with dry fine crushed sand (0/2 mm or 1/2 mm chippings depending on joint width). No machinery, not even a vibrating plate, must drive over a paved surface whose joints are empty.

Differential settlement under rolling loads occurs systematically when the bed exceeds the target thickness. Under the repeated passage of van or garbage truck wheels, a bed that is too thick at 60 to 80 mm undergoes internal rearrangement of its grains. The vertical kinetic energy of the axle is converted into horizontal thrust. Because the layer is not confined within its thickness, the chippings flow laterally out of the wheel track axis. The classic rutting profile then forms: a depression of several centimeters where the tyres pass, bordered by two extrusion ridges where the pavers are lifted.

Final mechanical tamping is carried out using a vibrating plate imperatively equipped with a neoprene or polyurethane elastomer pad to prevent chipping the edges of the pavers. The surface is scrupulously swept to remove any residual chippings before vibrating. Passes are made in cross-directions from the perimeter towards the center, causing the simultaneous sinking of the pavers by 5 to 10 mm into the loose bed. This movement forces the jointing material to rise from the bottom and locks the mineral skeleton without any residual breathing space.

Managing defects: repairing subsidence and rebuilding the bed

The appearance of differential settlement under rolling load a few weeks after commissioning signals an imbalance in the base structure. On a private road, this defect almost systematically stems from a bed exceeding tolerances or polluted with fine elements. When the channeled wheels create a hollow exceeding the permissible out-of-plumb according to standard SIA 318, simple surface leveling with a sand spreader or adding chippings under the sagging pavers constitutes a major technical error that will reproduce the defect shortly.

  1. Methodical removal and base diagnosisRemove the interlocking or sawn pavers over an area extending at least fifty centimeters beyond the deformed zone. Scrape away all the old bedding material down to the top of the foundation layer to inspect the support surface.
  2. Base layer inspectionCheck the flatness and compaction of the underlying untreated gravel. If the foundation shows a depression or was poorly compacted, it must be excavated, refilled with clean crushed gravel, and compacted to refusal before any repair of the paving.
  3. Relaying on a compliant calibrated bedScreed a new loose material without tamping it, maintaining a bedding layer thickness strictly between thirty and forty millimeters after tightening, using the correct particle size of bedding material without fines, such as 2/4 or 2/5 crushed chippings.
  4. Granular tightening and finishingRelay the paving pattern, fill the joints with polymer sand or washed 0/2 quartz sand, then pass the vibrating plate fitted with a polyurethane pad to lock the elements without breaking the edges.

Frequently asked questions

How to repair a localized rut without removing the entire paving of a walkway?

The rut must be delineated and the pavers removed for a minimum width of one meter around the deformation to find a stable base. Remove the existing chippings down to the foundation gravel. Check the compactness of the base with a penetrometer or a mechanical rammer. If the bottom is sound, spread a new 30 mm bed of 2/4 chippings, relay the pavers, fill the joints, and tamp with a protective pad.

Why does standard SIA 318 prohibit compacting the bedding layer before placing the pavers?

The bedding layer must remain perfectly regular and loose to absorb the dimensional tolerances of the pavers during initial adjustment. If the bed is pre-compacted, the pavers rest on isolated hard spots, which breaks the edges during final tightening and prevents uniform sinking. Compaction is carried out only once the pavers are laid and the joints sanded, thus guaranteeing a homogeneous transfer of vertical loads.

What chippings should be used for the bed of a vehicular driveway supporting delivery vans?

For a vehicular surface, standard SIA 318 recommends washed crushed chippings with a grain size of 2/4 or 2/5 millimeters, free of dusty particles smaller than two millimeters. The angularity of the crushed grains prevents internal rolling under tyre loads. Alluvial round sands or all-in-one materials containing fines are prohibited, because they liquefy under water and create rapid differential settlement under axles.

What should be done if the underlying gravel is too low by six centimeters relative to the theoretical level?

It is out of the question to fill this deficit with the bedding layer chippings, because such a thickness would cause immediate differential settlement under vehicles. You must obligatorily make up the shortfall with untreated foundation gravel of 0/32 or 0/45 particle size, then methodically compact it in layers until reaching the precise level allowing the regulatory bedding layer thickness to be maintained between thirty and forty millimeters.

Texts and standards cited

  • SIA 318External works: requirements concerning foundation layers, bedding layers, flatness tolerances, and execution of paved surfaces

In the same section