Key takeaways
- Partial contact at ninety per cent ruins the overall sound insulation of the door set.
- The mechanism must be triggered without rubbing as the leaf swings.
- The strict flatness of the flat threshold determines the uniform compression of the elastomer profile.
- The sheet-of-paper test confirms continuous sealing across the full width.
Adjusting the travel and release for a parallel drop
On an acoustic door, the automatic guillotine seal is the most vulnerable point of the work. Unlike the fixed perimeter seals compressed on three sides in the rebate of the frame, the bottom seal remains mobile. If the elastomer lip stops one millimetre from the floor along part of its length, or only presses against the floor over ninety per cent of the opening, acoustic leaks destroy the performance of the leaf. Air passes through, and sound follows the same path.
Protection against airborne noise inside buildings requires a seal without any discontinuity across the entire separating element, including the threshold.
norme SIA 181
The groove machined in the bottom rail of the leaf must follow the axis of the panel and the width specified by the mechanism manufacturer. A groove that is too tight pinches the aluminium profile and blocks its vertical sliding movement. A groove that is too loose allows unwanted tilting on impact. Before fixing the housing, check that there are no shavings and that the groove is straight over the full width of the leaf.
- Cutting the housing to lengthCut the guillotine seal to length on the side opposite the push button, observing the recommended setback from the edges of the door to avoid any contact with the frame.
- Fixing and centringInsert the housing into the bottom groove and secure it with the retaining brackets or fixing tabs supplied, making sure it is flush with the bottom edge of the timber.
- Adjusting the protrusion of the control buttonScrew or unscrew the plunger located on the hinge side (or the lock side depending on the model) so that the drop is triggered only in the last five degrees of the leaf's closing travel.
- Slope compensationOn models with dual adjustment, adjust the internal screw to obtain a drop parallel to the installation surface, even if the floor is slightly out of level.
Ensuring continuous contact on the threshold and preventing wear
The acoustic requirement set by standard SIA 181 tolerates no gap. A sealing defect of only ten per cent of the total length is equivalent to leaving a free through-opening of about ten square centimetres. To achieve the insulation measured in the laboratory, the seal must compress uniformly by between one and two millimetres over the entire clear opening.
| Parameter | Site requirement | Consequence of non-compliance |
|---|---|---|
| Flatness of the support | Deviation of less than 1 mm under the straightedge | Localised sound leak under the hollow |
| Compression of the profile | Even compression of 1.5 mm | Loss of insulation or binding of the leaf |
| Release of the plunger | Closing between 3° and 5° of angle | Tearing or shearing of the lip |
| Junction with the jambs | Tight contact against the frame | Acoustic bridge at both bottom corners |
The flatness of the floor under the door is decisive. Where the finished floor has a rough surface, hollow tile joints or a deformed screed, the joiner fits a ground flat metal threshold strip. This aluminium or stainless steel strip provides a strictly flat, abrasion-resistant surface. Without this support profile, the seal conforms poorly to local irregularities and wears quickly through friction.
Finally, the service life of the assembly depends on the return force of the spring. A guillotine seal that is compressed too much creates excessive mechanical resistance, which prevents the latch bolt from engaging in the strike plate without sustained manual pushing. The optimal setting ensures continuous tight compression while keeping the closing smooth, respecting user comfort and Swiss acoustic standards.
Impact of discontinuous contact on the acoustic requirement of standard SIA 181
On an acoustic door set, the real sound reduction tolerates no discontinuity in air-tightness. Acoustics does not allow approximation: assuming that a guillotine seal providing ninety per cent linear contact is sufficient is a serious technical error with heavy consequences. The remaining ten per cent of unsealed gap turns the bottom of the door into a direct acoustic bridge. Airborne sound energy rushes through the slightest millimetre-wide crack, ruining the overall insulation of the entrance or communicating door and causing the work to fail the acceptance measurements in situ prescribed by standard SIA 181.
Sound reduction depends on the tight confinement of the entire perimeter of the door leaf. The bottom guillotine seal acts as a dynamic mechanical barrier. As soon as the push button or release button strikes the strike plate or the frame, the internal scissor mechanism forces the sealing bar towards the floor. If the receiving surface has a hollow, an excess thickness of adhesive, a screed asperity or a level difference between two floor coverings, the tubular silicone elastomer lip cannot compensate for a gap greater than its useful elastic travel. Air passes through, and sound with it.
Method for validating continuous contact, threshold tolerances and preventing abrasion
To guarantee the contractual performance without premature wear of the rubber, the joiner must systematically check the regularity of the contact plane before locking the drop travel of the automatic seal. The release of the seal is always adjusted with the door closed, after checking the clearance at the back of the rebate and the plumb alignment of the frame.
- Checking the flatness of the closing thresholdPlace an aluminium precision straightedge under the path of the leaf. The finished surface (tiles, glued parquet, flat threshold profile) must show no sag or hollow along the line of impact of the automatic seal.
- Fine adjustment of the travelAdjust the setting screw of the control piston on the hinge side or lock side depending on the system (single or double release). The sealing bar must begin its descent parallel to the floor and touch the floor over its entire length at the exact moment the strike plate locks.
- Paper shim pull testInsert a strip of thick paper (approximately 120 g/m²) under the seal every fifteen centimetres, close the leaf and gently pull the strip. The resistance to pulling out must be uniform from one edge to the other with no point of free sliding.
- Checking the lifting kinematicsCheck that the mechanism retracts within the first few millimetres of opening of the leaf, so as to eliminate any abrasive rubbing of the lip against the finished floor.
| Finding on site | Technical cause | Corrective action by the joiner |
|---|---|---|
| No resistance in the paper test over 10 cm on the lock side | Asymmetric travel or uneven wear of the sealing lip | Readjust the balance compensation screw or replace the extruded silicone profile |
| Noisy rubbing and black marks on the floor when opening | Release button protruding too far, causing a premature drop before the door is fully closed | Loosen the push button by one or two turns to delay the mechanism's impact |
| Air passage and whistling under the door despite a compressed seal | Threshold concave in the middle of the opening or uneven tile junction | Fit a ground flat metal threshold, perfectly level, under the rebate |
| Bottom lip shredded or torn off after a few months | Constant friction on a rough floor covering or an unsmoothed threshold | Replace the seal, set the travel strictly and install a smooth threshold bar |
Seal wear almost always results from incorrect setting of the travel or from an untreated abrasive floor. Where the floor has hollow tile joints or a rough texture, fitting an extra-flat threshold plate in brass or extruded aluminium is the only lasting solution. This strip provides a machined, perfectly flat and smooth surface, ensuring both the continuous sealing required for sound insulation and the mechanical durability of the sealing lips under repeated opening cycles.
Remedial protocol in the event of a sealing defect or acoustic failure
On an interior joinery construction site, the failure of an in situ acoustic measurement according to standard SIA 181 almost always stems from a localised defect at the foot of the door. If the paper or feeler gauge check reveals an area without firm gripping, the installer must immediately isolate the source of the mechanical fault before considering any modification of the leaf.
- Locating the area of discontinuityClose the leaf and inspect the base using a raking light shone from the adjoining room, combined with sliding a 0.5 mm feeler strip. Identify whether the contact defect is on the hinge side, the strike plate side or in the central part.
- Checking the flatness of the floor and the geometry of the doorCheck the straightness of the floor with a two-metre straightedge under the path of the leaf. If the hollow exceeds two millimetres, the dropping profile cannot compensate for the gap. At the same time, check the warping of the door panel and the plumb alignment of the frame.
- Readjusting the mechanism and plumb alignmentIf the surface is flat but the seal drops at an angle, correct the travel using the adjustment screw located on the push button or on the opposite head depending on the manufacturer. Adjust the three-dimensional hinges to lower the leaf parallel to the finished floor.
- Fitting a ground threshold profileWhere the floor covering has a hollow that cannot be corrected by the other trades, add a bevelled aluminium threshold plate or a ground stainless steel strip, bonded level with polymer sealant, in order to recreate a strictly flat impact surface.
If the surface shows a deflection or an unacceptable irregularity attributable to the structural work or to the screed layer, the joiner formalises a notice of defects in accordance with the rules of standard SIA 118. Work on the mechanism must in no case conceal a flatness non-conformity that contractually belongs to the preparatory package.
Frequently asked questions
Can a hollow in the screed be made up by forcing the guillotine seal to drop further?
No. Forcing the plunger compresses the silicone lip against the high points without filling the central hollow. Air continues to pass and the sound reduction prescribed by standard SIA 181 is not achieved. Moreover, premature compression permanently deforms the flexible profile and slows the leaf on closing. The only compliant solution is to add a strictly ground threshold plate to provide a flat surface.
How can the seal's tightness be tested quickly after adjustment without a sound level meter?
The sheet-of-paper test remains the reference method on site. Insert a strip of 80-gram paper under the leaf every ten centimetres, then close the door. Pull gently on the strip: it must resist along the whole length without sliding freely. If the sheet comes out without resistance at any point, the contact is not continuous and the travel setting must be redone.
Why does the lip of an acoustic guillotine seal wear out prematurely?
Rapid wear almost always indicates a release that is too early or excessive travel. The seal must drop at the very last moment of the leaf's rotation, just before the latch bolt engages in the strike plate. If it touches the floor too early, the lip rubs in an arc on the rough floor covering, frays, loses its original tubular geometry and no longer ensures the required sound tightness.
Does the guillotine seal alone guarantee the sound insulation of the door set?
No. The bottom door seal is only one link in the acoustic chain. To meet the requirements of standard SIA 181, the perimeter seal on the frame must be flawless on the other three sides by means of continuous, flexible rebate seals. Likewise, the gap between the fixed frame and the masonry must be sealed with a dense acoustic foam or a continuous bead under sealant.
Texts and standards cited
- SIA 181Protection against noise in buildings: sound insulation requirements for interior building elements and doors
- SIA 118General conditions for the execution of construction work: handling of notices of defects and coordination between trades
