Key takeaways
- The cut-out dimensions supplied by the appliance manufacturer always take precedence over the overall dimensions.
- Applying a polyurethane resin or adhesive to the raw edge stops destructive water ingress.
- Ventilation under the hob requires a free air gap with no cross-rail blocking it.
- Wide cut-outs require steel ties or longitudinal reinforcements under the remaining strips.
Setting out the cut-outs and absolute sealing of raw edges
Cutting an opening in a wood-based panel to house a bowl or a hob is not something to improvise. The joiner must absolutely work from the technical fitting drawings of the appliance or sanitary-ware manufacturer, and not from the external overall dimensions of the appliance. The cutting dimension allows a precise functional clearance of two to three millimetres on each side to allow for expansion and clamping by fixing brackets, while keeping sufficient bearing for the upper support flange and its foam or elastomer seal.
- Marking out and corner pilot drillingPosition the marking on the upper or lower face depending on the cutting direction of the blade teeth. Drill the four corners with a guided twist bit to obtain a rounded corner radius.
- Sawing and mechanical guidingMake the straight cuts with a plunge-cut circular saw on a guide rail, then join the corners precisely with the jigsaw without overcutting.
- Deburring and levelling sandingDeburr the sharp edges with fine 120-grit sandpaper to remove cutting chips that would create starting points for delamination.
- Waterproof impregnation of the edgeApply a generous coat of D4 polyurethane adhesive, two-component epoxy resin or sanitary silicone, smoothed fully, over the entire height of the open edge.
Chipboard or high-density fibreboard absorbs moisture by capillary action from the first condensation under the drainer or when water overflows onto the worktop. Careful impregnation forms an impenetrable barrier. On laminated panels, complete the waterproofing treatment by fitting a self-adhesive aluminium vapour-barrier strip on the front lip and under the bowl edges to deflect residual drops.
Ventilation under an induction hob and handling of residual loads
Modern hobs, particularly induction hobs, generate considerable heat under their metal frame. The built-in fans must draw in tempered air and discharge the hot flow unobstructed. If the base unit blocks this circulation, the electronics go into thermal protection or suffer premature wear. The interior fitting must provide a continuous air passage in accordance with the appliance manufacturer's requirements.
| Fitting zone | Minimum requirement | Workshop or construction site measure |
|---|---|---|
| Slot under front rail | Clear height of 5 mm | Offsetting the drawer base or setting back the cross-rail |
| Vertical clearance under the frame | Gap of 20 to 30 mm | Fitting an intermediate protective base |
| Air discharge towards the rear | Section of 150 to 200 cm² | Trimming the top of the carcass back panel |
| Remaining cut-out margin | Rail of 50 mm minimum | Systematic reinforcement below 60 mm width |
Making large cut-outs for undermount bowls or wide hobs of eighty to ninety centimetres drastically weakens the worktop structure. The remaining strips at the front and rear are often only fifty to sixty millimetres wide. Under a service load or simply the weight of the filled appliance, these strips sag and break quickly if they are not relieved.
- Fitting a steel flat bar or a grooved aluminium T-profile under the remaining edge to prevent deflection.
- Fixing perforated metal spacer ties screwed directly to the side panels of the adjacent carcasses.
- Strengthening the top rails of the supporting unit with rigid angle brackets ensuring mechanical squareness.
- Fitting a heat shield under the hob when the unit below contains a cutlery drawer or sensitive equipment.
Machining to the fitting specifications and full-depth waterproofing of edges
The fitting sheets supplied by kitchen fitters and appliance manufacturers tolerate no approximation. A cut-out is never marked from the external body of the appliance placed upside down, but strictly from the cut-out dimensions of the technical housing, plus the prescribed functional clearance (generally 2 to 3 mm on each edge). Every internal corner must absolutely be made by pre-drilling with a wood bit or hole saw with a minimum radius of 5 to 10 mm. A sharp-cornered cut-out made in one pass with a jigsaw creates a local concentration of mechanical stress that triggers cracking as soon as the worktop is subjected to thermal stresses or repeated service loads.
| Worktop material | Machining method | Waterproofing system | Critical fitting point |
|---|---|---|---|
| HPL-laminated chipboard | Plunge-cut circular saw on rail, then orbital jigsaw for the drilled corners | D4-type fluid polyurethane adhesive or two-component epoxy resin spread with a spatula | Lightly sand the raw face before applying adhesive to open the pores and ensure penetration. |
| Glued laminated solid timber | Guided routing with a carbide spiral cutter | Saturating hard impregnation oil in three coats or waterproof polyurethane varnish | Treat the cut edges immediately on both faces to avoid asymmetric hygrometric deformation. |
| HPL compact panel | Machining with water cooling or reinforced extraction using carbide or diamond tooling | No impregnation required; mechanical chamfering of the edges with a 45-degree cutter | Soften the inner edges with 180-grit abrasive paper to remove machining micro-cracks. |
Applying sealing products requires a rigorous method. On wood derivatives, sanding with 80 grit removes the fibres torn out during sawing. The varnish, D4 polyurethane adhesive or hybrid sealant is applied in two crossed coats, taking care to run 1 mm up under the laminate film without overflowing onto the decorative face. Wait until it has dried right through before positioning the metal clamping clips: clamping too early on fresh adhesive scrapes off the protective film and destroys the waterproofing at the very spot where the hydraulic pressure of overflow water is greatest.
Air circulation for induction and structural strengthening of hollowed-out carcasses
Modern induction hobs dissipate considerable heat through their electronic components and require continuous airflow to avoid going into thermal protection. The joiner must provide a fresh-air inlet of at least 5 mm under the worktop nosing, often obtained by routing or by setting back the top front rail of the carcass. Under the metal housing, a free volume of at least 20 mm must be maintained above any fixed element. If a drawer is located under the hob, a deflector plate or an intermediate base in thin panel is mandatory to prevent textiles or cutlery from blocking the intake fans, while also protecting the user from accidental contact with the hot metal casing.
Installing an 80 or 90 cm hob or an undermount bowl dangerously weakens the work. The remaining front and rear bridges are often only 50 to 60 mm wide. Without mechanical reinforcement, these narrow strips bend or break when the panel is handled or under the weight of a full pot. The joiner screws metal angle or U-section profiles in steel or anodised aluminium under these strips, anchored into the sides of the adjacent units. If the appliance leaves no space under the worktop, a flat steel bar of 20 x 4 mm is set into a groove machined in the underside and bonded with structural resin before assembly.
- Checking the setting-out axes against the carcass sides and vertical uprights to exclude any unplanned overlap.
- Checking the radius of the corner cut-outs, without exceeding the tolerances permitted by the appliance manufacturer.
- Fitting a transverse metal angle to support the cut-out in the base unit when the panel cross-rail has been severed.
- Checking that there is no direct contact between the sink fixing claws and the raw, unimpregnated edge.
Damage and non-conformities: remedial procedures on the construction site
In a kitchen fit-out, defects resulting from a poorly executed cut-out appear in two forms: premature swelling of the panel core through water ingress, and repeated thermal protection tripping of the hob through overheating. When the worktop has been delivered or machined on site without watertight sealing of the raw edges, splash water penetrates the chipboard panel within a few days, causing irreversible delamination of the laminate. Likewise, omitting the air passages under the induction appliance forces the internal fans to draw in hot air in a closed loop, causing untimely shutdowns during prolonged cooking.
- Finding water ingress or swelling under the sinkIf the substrate has swollen locally, surface repair is impossible. Remove the sanitary appliance without damaging the unit below. If the swelling exceeds one millimetre in height, the worktop must be replaced or trimmed to receive a waterproof added strip. For a minor repair without deformation of the facing, dry the edge completely, remove friable particles, then saturate the panel with two-component epoxy resin before applying a new butyl sealing strip.
- Correcting the ventilation clearanceIn case of induction overheating, immediately check the air gap specified in the technical instructions. If the top rail of the unit blocks the air inlet, rout a 5 mm passage across the full front width or make a recessed cut-out in the upper base. At the rear, create a continuous gap of at least 20 mm between the back of the drawer and the rear wall to restore circulation towards the plinth.
- Restoring rigidity on a weakened spanA worktop that deflects under the weight of the bowl or a 90 cm hob suffers from insufficient bridging. Insert from below a steel angle or a 20x20 mm tubular steel section, screwed under the remaining edges and fixed to the side panels of the carcasses to neutralise mechanical deflection without hindering the fitting of the appliance.
Frequently asked questions
How do you repair a worktop cut-out made too wide for the appliance supplied?
If the clearance exceeds the tolerance of the support flange, it is forbidden to fill the gap with silicone sealant. The technical solution is to notch the underside to inset a strip of solid wood or compact panel, screwed and glued with polyurethane resin under the inner edge. This added piece restores the mechanical seating required for the appliance's clamping claws.
Can an induction hob be installed above a drawer unit without a protective base?
No. The installation instructions require an intermediate heat shield or non-combustible separating base located at a minimum distance from the underside of the appliance. This separator prevents any accidental contact between the contents of the upper drawer and the hot electronic casing, while guiding the cooling airflow towards the rear clearances.
Which adhesive should be used to permanently seal the inner edge of a built-in sink?
A fluid two-component epoxy resin or a moisture-curing polyurethane varnish offers the best barrier against standing water. Two crossed coats are needed to saturate the porosity of the particleboard. Class D3 white glues and acrylic paints are strictly prohibited because they soften quickly when a leak occurs under the sink.
Why does the instruction sheet for an 80 cm hob often require a specific cross-rail reinforcement?
Fitting a wide appliance often leaves less than 50 mm of material at the front and rear edges on a standard 600 mm worktop. Without a metal stiffener tied to the carcass sides, the remaining strip bends under its own weight or when a heavy pan is placed on it, causing the worktop to crack or the glass-ceramic to break.
Texts and standards cited
- norme SIA 118General conditions for the execution of construction work, contractor's duties and management of defects in the works.
