Skip to content
Website
🧱 CFC 273Claddings, skirting boards and parquet installationChapter 4 of 10 in the section

Skirting boards: fixing, mitre cuts, joint against an out-of-true wall and future removal

On completing this chapter, the joiner will be able to set out, cut and fix skirting boards while respecting the parquet's freedom of movement. The practitioner will master measuring out-of-square corners, adapting to out-of-plumb masonry or plasterboard walls, and demountable assembly methods that allow later removal without damaging the floor covering.

Key takeaways

  • The skirting board must always be anchored into the vertical wall and never fixed to the parquet.
  • The perimeter gap required by SIA 253 ensures the free hygrothermal expansion of the boards.
  • Mitre cuts on out-of-square corners require a sliding bevel and an accurately transferred bisector.
  • Mechanical clips and concealed screw fixing allow future removal without damaging the wall substrate.

Wall fixing and absolute preservation of the perimeter joint to SIA 253

Fitting a skirting board in interior joinery is not merely a matter of decorative corner trim. Its primary function is to conceal the technical perimeter void while ensuring the visual and acoustic seal of the wall-floor junction. Under the rules of the trade governed by SIA 253 on bonded and floating floor coverings, this perimeter void is the parquet's essential breathing zone. Any nailing, screwing or bonding directed into the boards locks the parquet against the wall and cancels this necessary movement, causing lifted spans or torn edges at the first seasonal change in humidity.

Anchoring is carried out exclusively in the vertical plane of the wall. Three fixing methods meet the requirements for holding power and reversibility: direct screwing with wooden plugs on masonry walls, stapling onto a metal or timber frame profile for lightweight partitions, and the use of metal clips plugged at the foot of the partition. Bonding with hybrid polymer sealant is permitted on plaster or smooth concrete, provided the bead is applied only on the upper third of the skirting board to avoid any glue flowing back into the perimeter gap below.

Skirting board anchoring methods according to the type of wall substrate
Wall substrateRecommended fixing methodFixing spacingRemovability
Shuttered concrete or raw masonryNylon plug and countersunk screw concealed by wooden plug500 to 600 mmExcellent: unscrew directly after removing the plug
Plasterboard dry partitionSpring steel clips plugged or screwed into the studs400 to 500 mmOptimal: clips off cleanly with a wide spatula without tearing
Cement screed or anhydrite flowing screedNo fixing permittedNoneNone: the floor must remain entirely free beneath the board's lower edge
Sound thin plaster skim coatMS polymer sealant in spaced vertical beads300 mm between beadsLow: risk of tearing the cardboard facing on removal

Skirting boards must be fixed so that the movements of the floor covering and of the substrate are not restrained and no mechanical stress is transmitted to the vertical elements.

norme SIA 253

Scribing to out-of-true walls, actual mitre cuts and removability

On Swiss construction sites, cast-in-place concrete walls or partition walls frequently show flatness defects, plaster bellies and corners that do not match the theoretical 90-degree square. Assembling skirting boards requires a rigorous method to eliminate gaps under the board and open mitres, while anticipating the need for removal for later low-voltage cable runs or future replacement of parquet boards.

  1. Measuring the actual angle with a sliding bevelMeasure the corner opening using a workshop sliding bevel or an electronic angle finder. Divide the actual value by two to set the compound mitre saw, rather than cutting at the default theoretical angle.
  2. Scribed cut or shouldered mitre cutOn an internal corner, prefer scribing the female skirting board onto the continuous male board, which avoids a visible opening of the joint when the skirting board itself shrinks with hygrothermal changes.
  3. Scribing the edge against the out-of-true wallHold the piece temporarily against the wall. Transfer the irregularities of the masonry onto the upper rear edge using a joiner's compass, then plane to the marked line with a hand plane or a plunge router plane.
  4. Height shimming and preserving the lower gapPlace sacrificial shims of 1 to 2 mm under the skirting board during fixing to avoid any abrasive rubbing on the varnish or oil of the floor, then remove the shims once the anchors are locked.
Scribing (or scribing compass)
A manual operation consisting of tracing the winding or bulging profile of an irregular wall onto the upper or rear edge of a piece of woodwork, so as to achieve a joint without visible gaps and without excessive filler.

The upper joint against rendered masonry is adjusted with a paintable low-shrinkage acrylic sealant, smoothed with a damp sponge, never spilling onto the visible face of the varnished woodwork. Sealing between the underside of the skirting board and the parquet board must remain excluded: the one-millimetre gap left by the temporary shims allows free air circulation under the parquet while absorbing the dynamic deflections of the floor under service loads.

Measuring out-of-square corners and scribing to irregular masonry

On renovation sites as in new construction, masonry walls or plasterboard linings frequently show out-of-plumb faces and corners that depart from the theoretical 90 degrees. A standard 45-degree mitre cut systematically leads to visible gaps at the face or edges that do not sit flush. The joiner measures the actual angle with a digital or mechanical vernier sliding bevel, then transfers exactly half the value to the turntable of the compound mitre saw. On an internal corner, a scribed joint made with a gouge or jigsaw remains superior to a simple mitre: it absorbs the seasonal dimensional variations of solid timber or composite board without opening.

  1. Measuring the actual bisectorPress the blades of the sliding bevel against the two wall faces at the exact height of the future skirting board. Lock the wing nut, read the angle and divide the value by two to set the head of the mitre saw.
  2. Marking out with a scribing compass on an out-of-true wallHold the skirting board level against the partition. Open the scribing compass to the maximum gap found between the back of the woodwork and the plaster, then draw a reference line parallel to the substrate along the upper face.
  3. Truing and ripping with the planeRework the back of the piece with an electric workshop planer or a low-angle hand plane to follow the bulge or hollow of the masonry, keeping a slight back-bevel towards the rear so that the visible edge closes perfectly.
  4. Adjusting the edge cutOffer up the adjusted piece, check that it sits against the wall without forcing the material, then dress the corner junctions flush with a joiner's rasp or a sanding block with 120 grit before fixing.
Skirting board assembly techniques according to geometric configuration
ConfigurationRecommended machiningTools usedShrinkage behaviour
External corner (closed or open wall)Mitre cut at the exact bisector with the mitre slightly open at the heelCompound mitre saw with 72-tooth carbide bladeSensitive to opening at the tip if the substrate moves
Internal corner (moulded solid timber)Scribing the front face onto the adjacent profileTilting jigsaw and carving gougeInvisible on drying, perfect visual joint maintained
Internal corner (straight or chamfered profile)Butt cut with 45-degree mitre returnCompound mitre saw and workshop squareStable closed joint, quick fitting on dry partitions
Butt joint over long lengthsScarf cut at 30 or 45 degrees, facing away from the line of sightCircular saw on a fine guide railNeutral longitudinal sliding without any step at the face

A wall with pronounced irregularities must never be dealt with by forcing the fixing tight. Forcing a solid oak or veneered MDF skirting board against hollow masonry creates internal stresses that distort the profile, pull out the anchors or instantly open the mitre joints at the ends. Adaptation is always achieved by removing material from the back of the piece.

Removable wall fixing and sealing to SIA 253

Removability is a central requirement to allow repair of a damaged board, later sanding or the discreet routing of extra-low-voltage cabling. The joiner prefers invisible mechanical fixings by metal clips or hanging profiles plugged into the frame or masonry every 400 to 500 millimetres. On friable substrates or thermal linings where clips lose their hold, fixing with countersunk through-screws remains common: the countersunk heads are concealed by workshop plugs cut from the same timber, or positioned behind a flush rebate hidden by a clip-on skirting nosing.

  • Omega rail or spring clip system: screwed directly into the studs of lightweight partitions, they allow a clean unclipping by pulling upwards without damaging the wall paint.
  • Plugged technical battens: a continuous batten fixed to the wall, onto which the cover skirting board engages by tongue and groove or is held by neodymium magnet inserts.
  • Paintable acrylic joint at the top edge: a flexible bead smoothed with a damp finger to compensate for micro-gaps in the plaster, with no mechanical bond to the upper face of the woodwork.
  • Acoustic decoupling at the floor: prior fitting of a strip of compressible cellular foam at the heel to prevent impact-noise transmission between the floating screed and the skirting board.

When the surface condition of the partition requires a finishing seal, the sealant used must remain strictly flexible and compatible with painted backgrounds. Any rigid elastomer joint or sealant adhesive at the lower part that would run into the expansion gap is prohibited. The parquet must keep its full freedom of horizontal sliding under the thickness of the skirting board, in accordance with SIA 253 and the rules of the trade for Swiss finishing work.

Handling non-conformities, parquet restraint and removal procedures

On finishing-work construction sites, the major defect found at the finishing inspection remains the restraint of the floor covering by through-fixings. When a fitter nails or screws a skirting board directly into the parquet boards, or when contact adhesive oozes under the lower edge, the natural expansion of the timber is obstructed. At the first seasonal changes in humidity, the parquet lifts in a dome or its edges separate. The finding requires complete remedial work: every fixing that ties the cladding to the floor must be removed without delay.

Diagnosing skirting board defects and remedial methods in the workshop or on site
Defect observedTechnical causeCorrective measure in the workshop or on site
Cupping or lifting of the parquet at the foot of the wallSkirting board fixed mechanically into the parquet, eliminating the gap required by SIA 253Remove completely, free the 8 to 12 mm perimeter gap, refix exclusively into the partition
Gap at the top on an out-of-true wallNo scribing to the wall, or excessive shimming at the bottomRework the back edge by fitting plane according to an accurate compass measurement
Open mitre after the piece has shrunkTheoretical 45° cut on an actual obtuse or acute angle without measuring with a sliding bevelReplace the corner joint with a fitted piece or redo the cut to the exact bisector

Facing masonry with a pronounced out-of-plumb exceeding the permissible tolerances, the mistake is to force the skirting board mechanically against the substrate. The tension pulls out the plugs or makes the woodwork buckle. The joiner scribes an adjusting profile with a compass or fits a concealed intermediate packing shim, completed by a flexible elastoplastic sealant at the top edge. To guarantee future removability without tearing the plaster, the use of screwed metal clips or screws under flush wooden plugs remains the proven method, excluding destructive polyurethane adhesives.

Frequently asked questions

How do you free a solid parquet nailed by mistake through the skirting boards?

The rigid connection between the floor timber and the vertical cladding must be cut without delay. Remove the skirting board by sliding in a wide, protected spatula so as not to crush the plaster. Remove the through nails or cut them flush with the parquet using flat cutting pliers. Check with a light crowbar that the parquet slides freely under the cut line, then refit the skirting board, anchoring the fixings mechanically in the wall only.

What solution should be applied if the masonry angle varies between the bottom and the top of the skirting board?

On a tall skirting board, a wall corner may show a twist in the masonry. The measurement is taken with a sliding bevel combined with a cardboard template or a bevelled gauge rod. To absorb the variation without creating an unsightly gap, fit the mitre-on-mitre in the workshop with a slight rear back-bevel on the compound mitre saw, then dress the edge with a bench plane to match the reference face.

How do you deal with a large upper gap between the skirting board and a very irregular rustic render?

Never fill a void of more than three millimetres with a simple bead of acrylic sealant, as it would crack on drying. Mark the exact profile of the hollows and bumps on the back of the skirting board with a joiner's compass. Then plane the rear face along this line to recess the moulding as close as possible to the surface, then apply an elastomer seal smoothed with a finger wet with soapy water.

Why does SIA 253 prohibit rigid fixing at the bottom of the skirting board?

SIA 253 requires the free dimensional movement of bonded or floating floor coverings in response to variations in the relative humidity of the ambient air. A fixing at the bottom of the skirting board locks the boards around the perimeter of the room. This mechanical restraint generates destructive internal stresses that cause the floor to buckle in the middle of the room, tear-out cracks in the timber and failure of the tongue-and-groove joints.

Texts and standards cited

  • SIA 253Timber floor coverings and parquet: installation requirements, perimeter joints and conditions for decoupling skirting boards

In the same section