Skip to content
Website
🧱 CFC 273Claddings, skirting boards and parquet installationChapter 3 of 10 in the section

Laying direction and layout planning: light, room length and last board

Choosing the laying direction and planning the layout of a parquet floor must not be improvised on the first row. This chapter guides you in orienting the boards along the light axis or the perspective of the room, anticipating the width of the last row to avoid unstable slivers, and ensuring end-joint staggering that complies with good practice.

Key takeaways

  • The board direction is aligned first and foremost with the main source of incident natural light.
  • In narrow rooms or corridors, the longitudinal direction always takes precedence over the orientation of the glazed openings.
  • The width of the final row is calculated before gluing in order to balance the first and last rows.
  • The staggering of end joints must be at least one third of a board or fifty centimetres.

Determining board orientation between light input and floor plan geometry

On a Swiss interior joinery construction site, the orientation of the parquet determines the visual perception of the room and the mechanical behaviour of the floor covering. The basic rule of the trade is to orient the boards perpendicular to the main glazed façade, that is, parallel to the incident rays of light. This orientation reduces the shadows cast by the permissible unevenness along the longitudinal edges and highlights the grain structure of the wood without emphasising the micro-relief of the joints.

The planning of the laying of timber floor coverings must take into account the effect of natural light, the geometric shape of the rooms and the foreseeable direction of dimensional changes caused by climatic variations.

Norme SIA 253

However, the geometry of the room frequently takes precedence over lighting. In strongly asymmetrical rooms, corridors, circulation galleries or narrow rectangular rooms, the boards must follow the direction of the greatest length. Transverse laying in a corridor creates an unattractive visual barring effect, multiplies end cutting waste and increases expansion stresses on the long sides of the partitions.

Choosing the laying direction according to the room configuration
Room configurationRecommended orientationTechnical and aesthetic justification
Through living room with opposite openingsParallel to the dominant light axisConcealment of longitudinal joints when viewed from the usual viewpoint
Corridor, circulation space, narrow roomAlong the length of the roomDimensional stability and reduction of cutting waste
Square room with a single openingFacing the main windowRaking light running along the bevels of the boards
Suite of several connected roomsContinuous guiding line along the entrance axisSpatial harmony without unnecessary steps or threshold breaks

Calculating the layout: transverse distribution and staggering of end joints

The classic mistake is to start against the reference wall with a full board without having measured the total remaining width. If the perimeter gap and the accumulated usable widths lead to a last row of two centimetres, the board becomes almost impossible to fit, unstable when glued and visually unacceptable under SIA 253. The width of the last row is determined from the initial marking-out.

  1. Measuring and deducting expansion gapsMeasure the net width of the room between masonry or finished partitions at several points to identify out-of-square conditions. Deduct the perimeter expansion joint on each side, generally ten to fifteen millimetres depending on the species and the laying system.
  2. Calculating the number of rows and the remainderDivide the corrected clear distance by the usable width of one board. The result gives a whole number of full rows and a theoretical remaining width for the final row.
  3. Symmetrical distribution on the first rowIf the calculated remainder is less than one third of the width of a board or six centimetres, add the width of one full board and divide the total by two. Rip the starting row to this value to balance both edges perfectly.
  4. Marking out with a chalk lineMark a strictly straight starting line on the screed at the dimension of the corrected first row, without blindly copying any curvature of the starting partition.

At the board ends, the distribution of the butt joints ensures bracing and uniformity of the flooring. Random-length laying uses the offcut from the previous row to start the next one, provided that this piece measures at least thirty to fifty centimetres depending on the timber format. For large-format boards, SIA 253 and good practice require the transverse joints to be staggered by at least one third of the element length, or fifty centimetres, to avoid overly tight stepped alignments that weaken the mechanical connection of the parquet.

Setting out the axis and recalibrating the first row

On the construction site, masonry and dry-lining partitions rarely show perfect parallelism. Laying the first row of parquet directly along the wall without anticipation condemns the last row to absorb all of the out-of-squareness, with the risk of ending up with a tapered sliver of wood that cannot be properly nailed, glued or clipped. SIA 253 prescribes execution tolerances for glued or floating floor coverings that require strict dimensional control of these edge elements.

To comply with the minimum width requirement for the last row, the joiner sets out the reference line with a chalk line from the median longitudinal axis of the room. The total dimension measured from wall to wall is divided by the usable width of the boards, after deducting the perimeter gap required by SIA 253 for timber expansion. If the remainder of the division gives an edge width of less than 50 mm, the starting line must be shifted transversely by half a board width. The first and last rows are then ripped lengthwise on the table saw in order to balance the visible edges on both sides of the room.

Adjusting the initial ripping according to the theoretical residual usable width
Calculated gross residual dimensionConsequence with direct layingCorrective action on the initial rowFinal width of each edge
< 30 mmUnstable sliver, risk of splitting when nailing or of joint failureRip the first row by half the width of a standard boardApprox. 60 to 90 mm (balanced)
30 to 49 mmNon-compliance with the usual requirements of SIA 253Distribute the difference: re-cut the first board by one third of its widthApprox. 70 to 95 mm (stable)
≥ 50 mmCompliant with bearing and retention tolerancesKeep the full-width board at the start (except for correction of out-of-squareness)Greater than or equal to 50 mm

Staggering of end joints and fitting under stress

The board orientation is defined parallel to the axis of the main openings to erase the cast shadows at the bevels under raking light, while following the greatest dimension of the room to enhance the perspectives. This longitudinal arrangement demands great rigour in the staggering of the end joints. Random laying produces unintentional alignments known as "stepped" or "axe-stroke joints" that weaken the floor and disturb the view under natural light.

  1. Initial sorting of the timber and starting the rowOpen at least three packs at the same time to mix the colour shades and the grain of the wood. Use the offcut of the previous row to start the next row, provided that its length meets the normative threshold.
  2. Checking the longitudinal offsetCheck that the axial distance between two butt joints of adjacent rows is greater than or equal to the minimum value required by SIA 253, commonly set at twice the board width or at least 300 to 500 mm depending on the board format.
  3. Fitting and mechanical lockingEngage the tongue-and-groove or click-lock profiles with the pull bar and a tapping block of hardwood or polyethylene. Never strike the profiled edge directly with a hammer, as this will crush the upper lip.
  4. Fitting the last board against the wallMeasure the remaining fitting dimension, deducting the thickness of the perimeter spacer. Tighten the edge row with a flat-heeled metal pull bar to ensure final locking without damaging the rough skirting or the lining.

Managing the junctions under fixed frames requires coordination with the thickness of the adjacent floor coverings. Where the parquet meets tiling or an exposed screed, the transition is made by a flush threshold bar or a recessed metal profile, fixed while respecting the independence of the two coverings. Full-bed bonding under the threshold ensures the dimensional stability of the timber panel while allowing the main surface to move freely towards the perimeter edges.

Correcting alignment drift and managing non-parallel edges

When the initial layout has not anticipated out-of-square conditions or dimensional variations of the walls, the fitter faces a last row cut in a taper or with a residual width below the minimum prescribed by SIA 253. An end board narrower than 50 mm compromises the mechanical hold of the tongue-and-groove joint or the click-lock profile, while also harming the overall appearance of the room.

  1. Compensatory ripping at the startIf the problem is noticed before gluing or final locking of the first rows, the solution is to lift the rows already laid in order to re-rip the first row against the starting wall. Distributing the residual dimension between the first and the last row ensures a balanced width on both sides of the room.
  2. Reinforced connection of the final rowWhen correction at the start proves impossible on a glued parquet that is already setting, the last narrow board must be joined by full gluing on its underside and on its groove to the previous row. It is inserted with a metal pull bar, protecting the machined edges with a sacrificial block to avoid crushing the fibres.
  3. Adjusting for out-of-squarenessTo absorb an out-of-squareness greater than 10 mm over the length of the room, the cutting line of the last row is marked by scribing or by transferring it with parallel compasses. The perimeter expansion gap required by SIA 253 must be scrupulously maintained at every singular point along the skirting boards.

Frequently asked questions

Why should the boards preferably be oriented in the direction of the natural light?

Laying oriented towards the main light source reduces the visibility of unevenness and longitudinal joints under raking light. If the boards were laid perpendicular to the glazed openings, every tiny variation in thickness or micro-bevel would cast a shadow visible from the entrance of the room, impairing the visual result of the finished work according to the usual aesthetic criteria of finishing work.

How do you choose between the direction of the light and the geometry of a narrow room?

In a corridor or a very elongated rectangular room, length must take precedence over light input. Laying transversely would multiply end cuts, weaken the mechanical hold of the parquet and increase the risk of dimensional instability under humidity variations. Good practice requires aligning the long side of the boards with the main circulation axis to limit cutting waste.

What is the minimum permitted width for the last row of boards?

The width of the last board should not be less than 50 mm, nor represent less than one third of the nominal width of the standard board. A strip that is too narrow loses its shear resistance and makes normal click-locking or discreet nailing impossible. This dimension must be calculated during the preliminary marking-out in order to re-rip the first starting row if necessary.

What offset must be maintained between the end joints of two consecutive rows?

The transverse offset between the end joints of two adjacent rows must be at least 300 mm, or even 400 mm for wide boards longer than two metres. Insufficient spacing, such as a short stepped alignment, creates a line of structural weakness that promotes lifting or localised squeaking during seasonal cycles of shrinkage and expansion.

Texts and standards cited

  • norme SIA 253Laying of glued or floating floor coverings, requirements for substrates, flatness tolerances and sizing of perimeter expansion joints.

In the same section