Key takeaways
- A rigorous six-dimension survey neutralises the squareness and parallelism defects of the retained frame.
- Templating the new leaf compensates for the out-of-plumb condition without destructive planing on site.
- Reworking the hinge recesses requires three-dimensionally adjustable hinges or stable metal packing.
- A twist greater than eight millimetres rules out keeping the frame, for obvious acoustic reasons.
Six-point dimensional survey and geometry of a distorted frame
In old buildings, the openings undergo differential structural settlement. A retained frame almost never has truly vertical jambs or a level head. Taking measurements cannot be limited to a nominal width and height. To ensure that a flush or overlapping door can be made without excessive adjustments on the construction site, the joiner applies a systematic measuring protocol at six fundamental points on the internal rebate.
- Width measurement at three levelsMeasure the rebate-to-rebate dimension at ten centimetres from the threshold, at the mid-level of the lever handle, and then ten centimetres below the head, using a rigid tape measure or a calibrated laser distance meter.
- Height measurement at both endsTake the exact height from the finished floor to the head rebate, first against the hinge-side jamb and then against the lock-side jamb, in order to determine the transverse out-of-level condition.
- Checking the diagonals and the out-of-square conditionMeasure both rebate diagonals to quantify the parallelogram distortion of the frame. Use a workshop sliding bevel at the upper corners to calculate the actual cutting angle of the head.
- Measuring the twist with a alignment lineStretch two strings between the opposite diagonal corners. The gap, or contact with pinching at the central crossing point, reveals the overall twist of the closing plane, i.e. the warp of the door frame.
All these dimensions are recorded on a cutting sheet in the form of a developed template. Where the frame forms a pronounced parallelogram, the leaf must not leave the workshop with a standard rectangular geometry. The leaf is machined from the outset with a slope on its top edge and a leading edge with a calculated out-of-plumb angle. This anticipation in the workshop ensures a uniform perimeter clearance of three millimetres between the leaf and the existing frame, while observing the spacing needed for operation without binding.
Fitting the leaf, adjusting the ironmongery and rejection thresholds
Fitting a new leaf to an existing frame starts with respecting the alignment of the hinges. Keeping the frame means either using the hinge knuckles already in place or machining new recesses after filling the old ones. Reworking on the original ironmongery often requires custom recesses on the leaf, because the centre distance of period hinges matches no contemporary industrial pattern.
- Checking the strength of the female hinge knuckles sealed or screwed into the existing jamb.
- Filling the old hinge mortises with hardwood pieces glued with polyurethane adhesive before re-levelling.
- Possible replacement with three-dimensionally adjustable screw-in hinges after drilling threaded inserts into the timber jamb.
- Repositioning the lock keep to make up for the drop angle of the latch bolt and the deadbolt.
| Geometric defect | Permitted limit value | Corrective measure |
|---|---|---|
| Out-of-plumb hinge jamb | Up to 6 mm | Machining the leaf to a trapezoid and adjusting the ironmongery |
| Out-of-level head | Up to 5 mm | Mitre cut or bevelling of the top edge of the leaf |
| Warp or twist of the frame | Up to 4 mm | Bevelling the rebate edge and compensating elastomer seal |
| Sagging sill/bottom rail | Variable | Bevel planing of the bottom of the door according to the finished screed |
Keeping the frame reaches its technical limits as soon as the functional and standard tolerances can no longer be met. If the hinge-side jamb is out of plumb by more than six millimetres, the door's centre of gravity causes unwanted spontaneous closing or opening, which cannot be corrected without excessively warping the leaf. Likewise, a diagonal twist exceeding eight millimetres prevents even compression of the perimeter sealing gasket, which ruins the acoustic performance of the element.
Finally, mechanical deterioration of the substrate dictates stopping the renovation on a blind frame. A jamb split at the hardware, fungal rot at the foot of the frame caused by repeated cleaning, or a metal frame detached from the masonry all require complete removal. In this case, fitting a renovation frame covering the old frame, or outright removal and fitting of a new door frame, is the only lasting solution.
Fitting machining of the leaf and reworking of the hinge line
Transferring the survey to the raw panel rules out standard rectangular cutting. Each edge is machined to the actual geometry of the existing rebate, which is often trapezoidal. The marking-out includes the essential functional clearances: 3 mm at the head and on the lock side, 2 mm on the hinge side, and a floor clearance adapted to the floor finish (5 to 7 mm on a hard finished floor, increased if an automatic drop seal is planned). If the frame leans inwards or outwards, the closing edge is bevelled by the corresponding out-of-plumb angle, preventing the inner edge from jamming against the rebate at the end of rotation.
Reworking the ironmongery remains the most delicate operation. On a metal frame or a timber frame with fixed, non-adjustable hinges, the new leaf must exactly reproduce the height and the offset of the knuckles. If the knuckles have vertical play, brass friction bushes restore the seating without unsealing the frame. On a timber frame with recessed hinges, the joiner fits the leaf by cutting the recesses directly with a chisel after marking out with a marking gauge, or replaces the original hinges with screw-on renovation hinges, after drilling and plugging the old mortises with hardwood.
- Seating the panelPresent the pre-sized leaf in the rebate, held by wedges on the floor and 3 mm thickness shims on the edges.
- Transferring the hinge leaves with a marking gaugeMark with a knife the upper and lower edges of each knuckle directly from the frame onto the edge of the leaf.
- Recessing the hinge leavesRout out the recesses by machine or with a mortise chisel so that each leaf sits flush without creating any excess thickness.
- Dynamic checkHang the leaf, check free rotation and the evenness of the perimeter clearance before fitting the lock.
Technical limits of the existing frame and switch criteria
Keeping the existing frame is not always defensible. When the geometric or mechanical defects exceed the capacity of a new leaf to be fitted, the work becomes unstable and defective. The first obstacle remains spatial twist (warp). If the frame shows an offset between jambs greater than the flexibility of a solid-core door, the leaf will touch at a top corner while gaping at the bottom. A flexible tubular seal cannot compensate for a warp greater than 5 mm without requiring a violent slam or excessive effort on the key.
| Defect observed on site | Permissible tolerance | Technical decision | Required measure |
|---|---|---|---|
| Jamb/head out of square | Up to 8 mm over the width | Keep the frame | Re-cutting the leaf to a trapezoid |
| Spatial twist of the jambs | Less than 4 mm | Keep, subject to conditions | Fitting a flexible compensating seal |
| Spatial twist of the jambs | Greater than 5 mm | Removal and complete replacement | Fitting a new wrap-around frame |
| Deteriorated frame fixings | None (frame moves when pushed) | Refuse to install on the existing frame | Chemical anchoring or new frame |
| Certified fire-resistance requirement | None without system testing | Complete replacement mandatory | Complete VKF/AEAI-approved door set |
Standard requirements set limits that cannot be crossed. For an entrance door to a dwelling subject to fire protection requirements under the AEAI regulations, keeping an old frame deprives the work of any certificate of conformity. An EI30 leaf only guarantees its resistance within the frame-and-leaf system tested in a test laboratory. In terms of acoustics, airtightness requires even compression of the seal around the whole perimeter. A distorted frame with warped rebates produces direct sound leaks, rendering even the best sound-reduction assemblies useless.
The economic balance settles the decision definitively. Fitting a made-to-measure leaf on a heavily distorted frame requires long hours of precise surveying, non-parallel machining and adjustments on the construction site. If these manual operations exceed the cost of fitting a wrap-around refurbishment frame over the old frame, keeping the frame becomes counter-productive. The site supervisor will steer the client towards a complete solution including ironmongery, seals and factory finishes.
Decisions on the construction site: handling critical distortions and refusing to hang the leaf
Finding on site that a new made-to-measure leaf does not sit flat against the existing rebate means stopping the machining adjustments. If the twist of the frame exceeds the useful thickness of the acoustic seal, or if the cumulative out-of-plumb exceeds eight millimetres, planing the edges excessively or forcing the hinges weakens the structure without solving the air and noise leakage. The joiner exercises the duty to notify in writing to the site management, in accordance with the rules of the Code of Obligations (CO) and standard SIA 118. He records the actual geometric deviations precisely, supported by photographs and tracings, comparing the initial six-point survey with the situation found after removal of the old leaf.
Faced with a frame whose rebates are too damaged or whose lower seating is degraded by moisture, two technical salvage options remain before heavy demolition: - Refurbishment with a false rebate: if the clear opening allows, the joiner fits a machined stop bead, screwed and glued onto the stripped frame. This piece corrects the squareness, redefines a regular closing plane and incorporates a groove for an extruded elastomer tubular seal. - The overlay renovation frame: a wrap-around timber profile covers the existing jambs and head. This solution reduces the clear opening width by forty to fifty millimetres, but restores regular plumb lines without damaging the surrounding plaster or the plaster reveals.
When the anchoring of the frame in the masonry has lost all mechanical cohesion, or when the cost of manual rework exceeds the value of a complete installation, removal of the frame becomes essential. The site supervisor records the condition of the substrate in a joint report signed by all parties. Replacing the whole assembly with a block frame or a new reveal frame guarantees compliance with the tolerances of standard SIA 414, while protecting the company with regard to the durability and sound reduction of the work.
Frequently asked questions
How is the twist of an old frame compensated for when making the leaf?
A twisted frame shows an offset between its jambs. In the workshop, the leaf is not made warped, because it would lose its rigidity. The solution is to oversize the rebate thickness and to rip the lock-side edge with a controlled out-of-square angle. On the construction site, the fitter compensates for the residual out-of-plane condition by installing a perimeter seal with high compression or by adjusting the recess depth of the hinge leaves.
Can the existing hinges sealed into the timber frame be reused?
Reusing the original male hinge parts avoids cutting into the frame, but requires finding female hinge parts of strictly identical pattern for the leaf. If this hardware cannot be found or is distorted, the old knuckles must be ground flush with the timber. The joiner then fills the recess with a glued hardwood piece, then machines new recesses to fit three-dimensionally adjustable hinges screwed into sound material.
What clearance should be allowed for during the six-point dimensional survey?
The survey records the width at the top, middle and bottom, as well as the heights on the left and right. When ordering the raw leaf, the joiner deducts a standard theoretical clearance of three millimetres per edge and five millimetres at the floor. On an out-of-square frame, he keeps a ripping allowance of ten millimetres on the stiles in order to re-cut the out-of-plumb condition precisely with a plunge saw on the construction site.
At what level of distortion should keeping the old frame be abandoned?
Keeping the frame is abandoned when the out-of-plumb exceeds ten millimetres over the height or when the out-of-square condition of the diagonals exceeds twelve millimetres. At this stage, planing the leaf would remove the solid timber lipping and destroy the bond with the tubular core. Moreover, a frame that is split, worm-eaten or detached from the partition can no longer take the pull-out torque of a heavier modern leaf, which requires complete removal.
Texts and standards cited
- SIA 118General conditions for the execution of construction work, handling of defects and the contractor's duty to notify.
- SIA 414Dimensional tolerances in building construction for fitting interior joinery elements.
- code des obligationsRules governing the contract for work and services and the craftsman's duty of care in the presence of a defective substrate.
