Key takeaways
- Measuring at three distinct heights immediately reveals bulges and out-of-plumb in the walls.
- The most unfavourable dimension determines the fabrication width of the cabinet carcass.
- Systematic checking of the diagonals prevents carcasses from jamming in closed corners.
- Adjustment filler strips absorb the permissible deviations according to SIA 343 without any rework in the workshop.
The three-height method for detecting out-of-plumb and wall bulges
Measuring a recess or a section of wall at standing height with a single laser distance meter reading is the classic mistake of the hurried installer. On the construction site, plasterboard-block partitions, ventilated linings and raw concrete walls regularly show deviations from vertical. In the workshop, the joiner cuts and assembles perfectly rectangular, rigid and square carcasses. If the survey misses the narrowing caused by a partition leaning inwards or by an overly generous plaster build-up at mid-height, the unit will not fit into the opening. The joiner is then forced to plane the sides on site, demolish the plinths or send the furniture back for machining, which destroys the profitability of the job.
Doors and interior fittings must be designed and installed taking into account the permissible construction tolerances of the structural work and the finishing work, by providing suitable clearances and adjustment elements.
norme SIA 343
To neutralise these geometric deformations, the systematic survey is carried out on three precise horizontal planes for each wall concerned: the low dimension taken at 100 mm from the finished floor (at plinth or skirting level), the middle dimension taken at 1000 mm (critical height corresponding to the worktop, the drawers or the drawer fittings), and the high dimension taken 50 mm below the edge of the ceiling or cornice (generally between 2200 mm and 2500 mm). These three measurements must also be repeated across the depth of the fitting: one measuring line at the back of the recess (against the load-bearing wall) and one measuring line in line with the future front.
| Survey zone | Measuring height | Dimension measured at the back | Dimension measured at the front | Geometric finding |
|---|---|---|---|---|
| Upper level | 2400 mm | 2412 mm | 2408 mm | Opening at the top |
| Middle level | 1000 mm | 2394 mm | 2402 mm | Wall bulge on the left partition |
| Lower level | 100 mm | 2405 mm | 2404 mm | Partition base compliant |
| Summary | Three heights | 2394 mm (min.) | 2402 mm (min.) | Dimension adopted: 2394 mm |
Squareness, diagonals and the tilting diagonal of the furniture
A recess can have a constant width at its three heights while forming a distorted parallelogram. In an acute corner (less than 90 degrees), the rear face of a standard carcass butts against the lining before its front face reaches its intended alignment. Conversely, in an obtuse corner (more than 90 degrees), the unit touches the wall at the front but leaves an unsightly trapezoidal gap towards the back. To reveal the real squareness of the walls, checking the diagonals remains the most reliable diagnostic tool in the field.
- Checking the angle with the 3-4-5 methodOn the two walls forming the corner, mark precisely in pencil a point at 600 mm on one wall and a point at 800 mm on the other, starting from the internal corner. The straight-line distance between these two marks must be exactly 1000 mm. Any deviation greater than 2 mm reveals an angle that departs from a perfect right angle.
- Checking the diagonals of the roomFor a U-shaped layout or a closed room, measure the two long crossed diagonals from corner to corner at floor level, then repeat the operation under the ceiling. Two identical diagonals confirm the parallelism of the faces and the overall orthogonality.
- Calculating the tilting diagonalA tall carcass assembled flat on the floor requires a clearance height greater than its nominal height when it is tilted upright. The hypotenuse formed by the height of the unit and its depth must remain at least 20 mm less than the lowest ceiling height measured in the area.
- Defining the width of the filler stripsSize the edge filler strips with an oversize of at least 15 mm to 20 mm relative to the maximum out-of-plumb measured. This extra material allows precise scribing with a scribing compass to fit the irregularities of the masonry perfectly.
Rigorous handling of these surveys protects the company against disputes and unplanned extra costs. The dimensional tolerances of the preceding trades (reinforced concrete structural work, lightweight partitions) are defined by Swiss construction standards but never match the millimetre tolerances of fitted joinery. Incorporating edge adjustment filler strips and removable adjustable skirtings is the only guarantee of a smooth installation in strict compliance with the rules of the trade.
Determining the minimum usable dimension and managing dimensional deviations
Once the measurements have been taken at floor level, mid-height and under the ceiling, supplemented by the check of the recess diagonals, the joiner is faced with a set of diverging figures. A raw masonry wall, a plasterboard lining or a float-finished render systematically shows surface irregularities, bulges or out-of-plumb. If an average value or the dimension taken at eye level is used to start cutting the panels in the workshop, the fitting will jam when inserted on the construction site. The fundamental rule of fitted joinery requires isolating the most unfavourable dimension, that is, the narrowest opening dimension in each plane.
The most unfavourable dimension does not only concern the clear width between walls. It applies jointly to depth and height. In width, the critical dimension corresponds to the tightest point created by the out-of-plumb of a partition or the bulge of a lining. In height, it is the minimum distance between the highest point of the screed or finished parquet and the lowest point of the ceiling, often obstructed by a beam downstand or a sagging suspended ceiling. In depth, the closed internal corner reduces the space available towards the back of the carcass. All the fixed elements of the fitting must fit entirely within this theoretical minimum volume.
| Measuring point | Dimension measured | Technical finding | Impact on fabrication |
|---|---|---|---|
| Floor width (H = 50 mm) | 1854 mm | Skirting and partition base compliant | Stable base for the technical plinth |
| Middle width (H = 1200 mm) | 1842 mm | Plasterboard partition bulge (+12 mm) | Most unfavourable dimension: maximum width of the bare unit set below 1842 mm |
| Upper width (H = 2450 mm) | 1860 mm | Out-of-plumb leaning outwards towards the top | Provide a wide trimmable filler strip to conceal the gap at the top |
| Left / right diagonal | Deviation of 18 mm | Trapezoidal recess out of square | Strictly rectangular fabrication, rear shimming mandatory |
Sizing installation clearances and shaping adjustment filler strips
Once the minimum dimension has been identified, the fabrication width of the carcasses must never equal this limit value. Inserting a unit between two walls requires a manoeuvring clearance to slide the elements in without damaging fresh paintwork or catching on a grain of render. The overall width of the cabinet carcasses corresponds to the most unfavourable dimension reduced by an installation allowance. This allowance is filled at the sides and at the top by filler strips, also called compensation strips or adjustment false frames. These visible pieces, deliberately supplied wider from the workshop, are profiled and cut to measure on the construction site with a plane or a plunge saw to fit the exact outline of the existing wall.
- Defining the usable width of the carcassesTake the narrowest dimension measured at the three heights and subtract the combined width of the two workshop adjustment filler strips (generally 50 mm on each side) to obtain the total gross width of the modular assembly.
- Validating the insertion diagonalCalculate the side diagonal of the carcass to check that it can be tilted upright under the ceiling at the lowest point without catching the concrete or the plaster, or plan assembly directly in the vertical position on plinth adjusters.
- Cutting adjustment filler strips to lengthScribe the curvature of the wall on site onto the edge of the raw filler strip using a joiner's compass or a calibrated feeler shim, while holding the unit in position with an alignment laser.
- Planing and bevel cuttingMake the cut with a slight back-bevel towards the rear to ensure clean, tight contact of the visible edge against the rendered or painted wall.
The fitting survey notebook must record all the dimensions measured and highlight the critical point circled in red pencil or coded distinctly in the computer-aided design software. The cabinetmaker or workshop technician programmes the CNC machining on this basis alone. On construction sites with tight deadlines, using generously sized adjustment filler strips is the only guarantee of avoiding remedial work on the masonry or a costly return of the carcasses to the cutting workshop.
Managing major deviations: rework on site and workshop decision
When installation on site reveals an unforeseen out-of-plumb or a masonry bulge exceeding the permitted tolerances, the fitting inevitably jams in its recess. If the measured dimensional deviation exceeds the oversize of the adjustment filler strips cut in the workshop, the joiner must on no account force the carcass against the partition. Such stress would bow the side panels, block the normal sliding of the drawers and distort the alignment of the faces as well as the peripheral clearance of the doors prescribed by SIA 343. Faced with this jam, two technical options arise: adaptation by joinery on site or formal reporting of a non-compliant substrate.
- Locating the binding point preciselyMark the tight zone with the laser level and a bevelled rule. The obstacle generally comes from a localised lump of plaster, a skirting junction or a room diagonal that is too short and closes the installation angle.
- Checking the cutting margin on the filler stripsCheck the remaining width of the lateral adjustment pieces. If ripping a filler strip makes it possible to follow the defect without cutting into the visible edge of the unit or straining the fittings, trim the piece with a guided circular saw fitted with a splinter guard.
- Refusing destructive notching of the unitIf the body of the unit itself hits the masonry, refuse to notch the side panels or the back panels. This improvised cut ruins the structural rigidity of the carcass, destroys the geometry of the drawers and voids any manufacturer's warranty.
In heavy renovation as in new construction, returning a carcass to the workshop for trimming or for fabricating a compensating module is always more cost-effective than a forced installation doomed to later complaints. Keeping a hollow clearance gap or systematically providing filler strips of at least fifty millimetres gives the essential safety margin against partition deformations. When the substrate shows obvious deviations, drawing up a rigorous metrological survey protects the company and allows the unforeseen adaptation hours to be covered.
Frequently asked questions
Why does a survey taken only at floor level condemn the installation of a built-in wardrobe?
A survey taken at floor level ignores the batter and out-of-plumb of the vertical walls. If the walls narrow towards the top or bulge at mid-height, the rigid carcass built to the floor dimension will not pass when slid into the recess. Taking three horizontal dimensions at different heights makes it possible to detect this narrowing and to adjust the fabrication width to the narrowest dimension.
How can the squareness of a recess be checked quickly without heavy optical equipment?
The Pythagorean three-four-five triangle method remains the most reliable manual solution on the construction site. Measure sixty centimetres along one wall from the corner, then eighty centimetres along the adjoining wall. The exact diagonal between these two points must measure precisely one hundred centimetres. Any deviation signals an open or closed angle that will require bevelling the adjustment filler strips or reducing the usable depth of the fitting to absorb the wall misalignment.
What deduction rule should be applied to the most unfavourable dimension?
After surveying the dimensions at three heights and three depths, always keep the smallest measured value. Then deduct a minimum lateral installation clearance of ten to fifteen millimetres on each side to accommodate the filler strips. This allowance compensates for grain irregularities and render roughness and allows the units to be inserted without rubbing the fresh paint of the partitions during final placement of the work.
Why must the tilting diagonal be measured before fabricating a full-height unit?
A carcass built lying on the floor must be able to be tilted upright without jamming against the finished ceiling. The diagonal of the side of the unit, calculated between the lower rear corner and the upper front corner, is geometrically greater than its plain height. If this diagonal exceeds the minimum ceiling height measured on site, tilting upright is physically impossible. The unit will then have to be assembled in the upright position or fitted with a separate movable plinth.
Texts and standards cited
- SIA 343Doors and gates: dimensional tolerances, functional requirements and adjustment clearances
