Key takeaways
- The systematic survey of access diagonals must always come before the cutting of panels in the joinery workshop.
- Handrails, radiators and light fittings drastically reduce the usable clearance in the winders of staircases.
- Splitting the piece into hand-carriable modules ensures safe two-person handling in line with Suva guidelines.
- Assembly with demountable fittings on site preserves final rigidity while getting past critical passages.
Surveying the critical access route and calculating the passage diagonals
A piece of fitted furniture made with cabinetmaker's precision becomes a total loss if it gets stuck at the first landing. Even before drawing up the cutting list or programming the machining on the CNC machining centre, the joiner must check the entire delivery route, from unloading the vehicle to the installation room. In older buildings as in recent rental blocks, the stairwell is the main bottleneck. The survey is not limited to measuring the visible width of the steps: it includes the permanent three-dimensional obstacles that reduce the dynamic envelope of the package. Protruding items such as landing radiators, suspended light fittings, surface-mounted electrical panels or wall handrails sometimes reduce the usable passage by fifteen to twenty centimetres. Ignoring these protrusions inevitably leads to destructive scraping against finished paintwork or to the physical impossibility of turning the piece.
- Checking the headroom and the windersIn a winding staircase, use a plumb line or a laser distance meter to measure the free height perpendicular between the nosing and the lower edge of the flight above or the suspended ceiling. In winders, the tread narrows towards the stairwell void: the joiner must carry the load on the outer side of the curve. Record the usable width by deducting the projection of the handrail.
- Calculating the three-dimensional diagonal of the packageThe real bulk of a piece of furniture is not its height but its spatial hypotenuse, calculated between two opposite corners taking depth, height and width into account. Always add fifty millimetres for protective thicknesses, such as blankets or cardboard corner protectors, as well as the space needed for the installers' fingers.
- Validating the clearance angles at landing doorsMeasure the clear passage width of the door frames once the leaf is opened at a right angle, as well as the setback available in the adjacent corridor. If the carcass exceeds the depth of the landing, it must be able to be tilted to the vertical before passing the door frame, which requires sufficient ceiling height to absorb the rotation.
Splitting the fitted furniture into hand-carriable carcasses and securing the installation
The feasibility of transport directly determines the construction design of the furniture. When the survey shows that it is impossible to get a single-piece unit through, the piece must be split into modular sub-assemblies without compromising the final appearance or the structural strength. This technical breakdown must comply with the rules on occupational health protection. The Construction Work Ordinance requires strict planning to reduce to a minimum the risks to health during manual handling. Carrying a carcass of more than sixty kilos up a narrow staircase exposes workers to loss of balance, crushing against walls and acute musculoskeletal injuries. The workshop must aim for packages that two people can handle, not exceeding forty to fifty kilos per individual module.
| Manufacturing parameter | Single-piece furniture | Split modular design |
|---|---|---|
| Unit mass handled | High (often over 80 kg) | Under control (under 45 kg per package) |
| Passage through the stairwell | Blocked from the first right angle | Smooth even with a winder |
| Assembly system | Fixed glued dowels in the workshop | Concealed draw-in fittings or Clamex |
| Fitting time on the construction site | Minimal if access is clear | Moderate for aligning plinths and carcasses |
To restore the integrity of the fitted furniture on site without visible screws, the joiner favours high-precision demountable assembly fittings, such as P-System demountable elements or eccentric connecting screws combined with mitred joints. The technical plinth is the first key element: made separately, it is levelled on the floor using adjustable feet before receiving the independent carcasses. Once the carcasses have been hoisted and placed side by side, the outer cladding panels, finishing side panels and compensation fillers cover the cutting joints. This approach removes the constraints of heavy handling while guaranteeing a continuous visual result, strictly identical to a piece of furniture pre-assembled in the workshop.
Handling in narrow flights: load limits and carrying equipment
Delivering fitted cabinetwork or bespoke wardrobes into an old building or a terraced house cannot be improvised at the foot of the building. When the staircase has winders, a helical stringer or a tight wall string, the mass of a machined carcass directly determines the safety of the installers and the integrity of the piece. The Suva recommendations on the manual handling of heavy loads set strict benchmarks for repetitive work and carrying on slopes. Continuous carrying of a panel or a volume by a single worker becomes critical beyond a reasonable threshold, systematically requiring two people or mechanised accessories suited to staircase flights.
The Construction Work Ordinance recalls that workstations and passageways must be arranged so that personnel are not exposed to any danger of falling or crushing. In a stairwell, the residual space for the feet and the visibility of the nosings disappear if the carcass exceeds the body envelope of the joiners. If a wardrobe carcass in 19 mm melamine-faced particleboard or medium-density fibreboard exceeds 45 to 50 kg, it must not be hoisted by arm strength alone without mechanical assistance or a load-spreading textile harness.
| Handling means | Useful capacity | Manoeuvring space required | Conditions of use |
|---|---|---|---|
| Direct manual carrying by two | Up to 50 kg | Average turning radius (1.10 m) | Requires rough-grip gloves, coordinated steps and clear landings. |
| Cross-over H-pattern shoulder straps | Up to 80 kg | Very low (full lateral clearance) | Load transferred to the trunk; perfect coordination is essential on winders. |
| Motorised tracked stair-climbing trolley | Up to 160 kg | High (minimum landing setback of 1.40 m) | Requires a sufficient curve radius and verification of the permissible load on the steps. |
| Indoor hoist on a prop tube | Up to 120 kg | Aligned on the stairwell void (min. 40 cm) | Requires confirmation of the floors' load-bearing capacity and a marked exclusion zone below. |
Rotation protocols, on-site reassembly and final fitting
Splitting in the workshop is only worthwhile if the reassembly system ensures perfect geometry once the furniture has been brought into the destination room. The foreman plans the trajectory by breaking it down into movements: linear progression along the flight, vertical tilting on the intermediate landing, pivoting around the stair handrail, then horizontal presentation through the landing door opening. Any forced contact between a carcass corner and plastered masonry damages the squareness of the panels and permanently marks the finish.
- Getting past the critical point in controlled rotationThe carrier at the lower end holds back the load while the carrier at the upper end guides the orientation. The element is tilted on its longest diagonal at the turn, maintaining a minimum clearance of 50 mm from protruding ironmongery or wall light fittings.
- Unpacking and methodical checking of the packages in the roomThe modules are placed on rigid foam blocks in the installation room, sorted in the logical assembly order from left to right or according to the layout plan, in order to avoid unnecessary cross-handling.
- Mechanical coupling of the split carcassesAdjacent carcasses are drawn together and clamped using pump clamps with soft jaws. The rigid connection is locked by eccentric housings concealed under the hinge baseplates or by nickel-plated through connecting sleeves of 5 mm diameter.
- Height alignment and overall levellingThe modular assembly is adjusted with a cross-line laser level by turning the adjustable plinth feet from inside the furniture, before any plugging into load-bearing walls or partitions.
- Fitting and cutting the compensation fillersThe out-of-plumb of the masonry walls is transferred with a joiner's marking gauge or scribing compass onto the fillers delivered with machining allowance, then cut with a plunge saw on a rail with splinter guard before concealed screwing.
The perimeter finishes require particular care to absorb the building's dimensional tolerances, governed by the rules of the trade and the recommendations of the SIA 118 standard. The fitted-furniture cabinetmaker provides for concealed assembly bores during manufacture and incorporates removable finishing side panels that hide the structural joints. This intelligent splitting turns a high-risk delivery into a rational installation, safe for the fitters and strictly in line with the client's expectations.
Managing blockages during transport: fallback protocols and dismantling in situ
When the piece jams at a turn despite the preparatory templates, the rule of the trade is to set the element down without trying to force the fitted furniture through the stairwell. Forcing a piece of furniture made of wood-based panel chips the thin edges, shears the dowels and breaks the mitre glue joints, while also damaging wall renders or nosings. The joiners wedge the load on neoprene pads to secure the support. According to the general principles of the OTConst, passages must remain secured against the tipping of heavy elements and kept clear to prevent any bodily injury during handling.
Faced with a dimensional dead end on a half landing, the foreman deploys the fallback actions in a methodical order:
- Removing attached elements: taking off interior door leaves, removing lever handles, door dampers and wall lights that reduce the usable passage section.
- Dismantling removable metalwork: unscrewing wall handrails after agreement from the site manager, taking care to maintain collective fall protection in the flight.
- Fully stripping the carcass: removing fronts, drawers, internal shelves and runners to lighten the furniture body and gain the few centimetres of extra thickness.
- Dismantling the structure in situ: mechanically separating the connections by demountable eccentrics or carefully unscrewing the back panel nailed or screwed in a rebate.
If the furniture was glued in the workshop without demountable fittings, splitting it on site requires a carefully considered technical intervention. The dividing cut line must be positioned with care behind a fixed upright, under an adjustment filler or in the exact alignment of a recessed joint. This operation requires a plunge-cut circular saw guided on a rule with splinter guard to obtain a clean cut, which can later be reassembled using self-clamping biscuits or pegged false tenons. If recutting compromises the mechanical strength or the finished appearance of the fitted furniture, lifting from the outside with a winch or a mobile crane becomes necessary. Any structural modification not provided for in the original quote is recorded in the site diary to formalise the adaptation services.
Frequently asked questions
What should be done if a tall piece of furniture gets stuck at the turn of a winding staircase?
The furniture must be stabilised where it is, without trying to pull it through by force. The installers check whether pivoting is restricted by a removable element, such as a protruding skirting board, a handrail or a chandelier. If the bulk diagonal remains greater than the clearance, the carcass must be brought back down backwards to the landing below. The splitting is then carried out on the floor by unscrewing the panels or mechanically separating the workshop connections.
What maximum weight per piece should be observed for two-person handling on stairs?
For manual carrying on stairs, the usual occupational health recommendations advise limiting the total load of a package to fifty kilograms for a pair, that is twenty-five kilograms per joiner. Beyond this mass, the risk of loss of balance or back injury increases sharply in steep flights. Any heavier element requires prior removal of fittings and shelving, or the use of a motorised stair-climbing trolley fitted with brakes.
Can a landing door be removed to make it easier to bring in a large piece of furniture?
Yes, unhinging the leaf of a landing door recovers the rebate thickness and the opening angle. However, if the landing door performs a fire-protection function, it must not be left open unattended during the works on the construction site. The hinges must be protected against impacts when the carcasses pass. As soon as delivery is complete, the leaf is put back in place and its closing clearance checked.
How should the common areas be protected when carrying bulky pieces?
Protecting existing structures starts with laying protective felt or cellular boards on the steps and landings. Nosings and wall-string edges receive corner protectors made of thick cardboard or expanded foam, fixed with adhesive tape that leaves no adhesive transfer. The sharp corners of the furniture are wrapped in removal blankets and film. These measures prevent disputes over the move-in condition report with the property manager.
Texts and standards cited
- OTConstRequirements on the safety and health protection of workers in construction work
