Skip to content
Website
🧱 CFC 273Fitted furnishings: survey, fabrication and installationChapter 7 of 10 in the section

Made-to-measure walk-in wardrobe: usable heights, hanging rails, and what the client is made to say about their habits

Designing a made-to-measure wardrobe requires asking the client precise questions about their habits before the first pencil stroke. This guide details the four essential preliminary questions, the usable depths and heights for each type of wardrobe, and the workshop provisions for recessing lighting and ensuring natural ventilation of the enclosed volume, without panel deformation.

Key takeaways

  • The survey of hanging and folded clothing volumes determines the initial layout of the vertical carcasses.
  • A hanging rail requires at least 580 mm of usable depth to prevent the hangers from rubbing.
  • Usable heights range from 900 mm for shirts to 1600 mm for long coats.
  • Integrating LED profiles and maintaining air circulation prevent overheating and ambient mould.

Surveying the needs: the four usage questions before drawing the carcasses

A made-to-measure wardrobe layout is not judged by the symmetry of its fronts or the quality of its finishes, but by its ability to absorb the actual clothing inventory without creating dead volume. All too often, the joiner draws modules of equal width before even asking about the occupants' daily habits. The result is overloaded rails topped by inaccessible shelves where clothes pile up in disorder. Technical design must begin with a methodical listening to the client's needs.

  1. 1. The ratio between hanging and folded clothingQuantify the linear metres of hanging rail required against the number of shelves needed. Someone who keeps shirts on hangers does not have the same needs as a user who favours folded knitwear and T-shirts.
  2. 2. The precise type of hanging garmentsDistinguish clearly between short and long garments. Providing too much height for shirts wastes valuable vertical volume, while a creased dress at the bottom of a carcass reflects an unforgivable design error.
  3. 3. Managing accessories and small itemsDetermine the number of closed drawers with compartments needed for underwear, belts and jewellery. These items require full-extension runners and an ergonomic position between knee and chest height.
  4. 4. Frequency of use and seasonal rotationIdentify everyday clothes, to be placed in the middle zone with direct access, and out-of-season items, which will go on the top shelves or in deep corners under the ceiling.

The usable depth of the unit follows directly from the closing system chosen by the client. With a conventional hanging rail, an adult hanger measures between 420 mm and 460 mm in width. Once the garment is on its hanger, the thickness of the fabric brings the average transverse space requirement to 550 mm, and up to 580 mm for a winter coat. With hinged doors, the minimum usable depth of the carcass is 580 mm. For sliding doors, 80 mm to 100 mm must be reserved for the double track and the clearance of the handle profiles, which requires a minimum total depth of 660 mm to 680 mm.

Recommended usable depths by type of layout
Type of storageNet usable depthRecommended total depthConsequence of underestimating
Standard longitudinal hanging rail580 mm600 mmSleeves rubbing when the doors are closed
Transverse telescopic hanging rail380 mm400 mmStorage capacity halved compared with a straight rail
Shelves for linen and T-shirts400 mm450 mmUnstable piles of clothes if too deep, or overhanging if too short
Shelves for flat shoes320 mm350 mmFront cannot be closed, or overhang into the circulation space

Execution dimensions: usable heights per garment, LED profiles and air renewal

The vertical distribution of the levels dictates the everyday ergonomics of the unit. A common execution mistake is to fix the rail too high or to neglect the space needed to get a hand in. A clear gap of at least 50 mm must be provided between the upper edge of the hanging tube and the underside of the top shelf so that the hanger can be hung easily. The usable heights are then calculated rigorously from the drop of the hanging garments.

Net usable heights under the rail by textile category
Garment categoryClear height under railTypical vertical spacingWorkshop recommendation
Shirts, jackets and short skirts950 mm1050 mmAllows two levels of short hanging to be stacked
Trousers hung by the waist1150 mm1250 mmTo be replaced by a sliding trouser rack under 800 mm
Standard dresses and mid-length trench coats1350 mm1450 mmKeep the lower part clear for placing boxes
Long coats and evening dresses1600 mm1700 mmProvide a separate module so as not to break the modular grid

Careful integration of lighting enhances the layout without creating glare. The joiner machines in the workshop a groove 15 mm wide and 12 mm deep, angled at 45 degrees in the inner edge of the upright or under the top shelf, to take an aluminium profile fitted with an opal diffuser. The machining must be clean, without chipping of the melamine, and provided with 8 mm blind holes guiding the wires towards the power supplies. The electrician then connects into these recesses without ever leaving cabling exposed.

Sizing the volumes: critical depths, hanging heights and load-bearing capacity

In interior fit-out under the CFC 273 standard, the functional failure of a wardrobe almost always stems from confusing overall dimensions with usable internal space. Building a carcass with an overall depth of 600 mm with sliding doors mounted on the inside reduces the hanging space to less than 510 mm: jacket sleeves rub against the door stiffeners, hangers pivot at an angle and the fittings force the sliding. For a hanging rail closed by hinged or sliding doors, the trade rule requires a clear space of at least 560 mm between the back of the rear panel and the rear face of the frame or inner track. Conversely, allocating this same 560 mm depth to shelves for jumpers or folded shirts creates dead volume or an unmanageable double row in daily use: the rear pile disappears from view and collects dust.

Usable heights under the rail and recommended depths by garment type
Garment typeUsable height under railNet carcass depthInstallation constraint in workshop and on site
Shirts, short jackets, suit jackets950 mm to 1050 mm560 mm to 580 mmRail axis positioned 60 mm below the top shelf, centred 280 mm from the back.
Trousers hung from the bottom1100 mm to 1200 mm560 mm to 580 mmAllows full-extension runners to be integrated for telescopic trouser racks.
Long coats, dresses, trench coats1500 mm to 1650 mm580 mm to 600 mmA clear space of at least 150 mm above the floor must be provided to avoid collecting dust.
Folded clothing (T-shirts, fine jumpers)250 mm to 300 mm per compartment380 mm to 420 mmBay width limited to 800 mm with 19 mm panel to prevent sagging.
Bulky jumpers, bedding, duvets350 mm to 450 mm per compartment450 mm to 500 mmMinimum shelf thickness increased to 25 mm, or front reinforcement with a solid timber edge strip.

Managing shelf spans is a critical sizing point. On a bay wider than 800 mm, a 19 mm melamine-faced chipboard or wood-based panel creeps under a continuous load of heavy clothing. Beyond this width, the workshop foreman must specify a 25 mm carcass thickness or incorporate a recessed metal stiffener on the underside of the shelf. Likewise, oval aluminium rails of standard 30 x 15 mm section sag under the weight of coats if the span exceeds 900 mm without an intermediate support fixed under the upper shelf.

Air circulation, LED strip integration and usage survey sheet

A made-to-measure wardrobe closed from floor to ceiling is a confined volume that retains the residual moisture of worn textiles. If the unit is placed against an external wall with a slight thermal bridge, the absence of ventilation quickly produces musty smells and a risk of fungal attack behind the back panels. The joiner must provide a 20 mm air gap between the bare wall and the back of the unit, complemented by a passive through-flow of air: an invisible 10 mm undercut set back from the lower skirting and an exhaust slot of equivalent section in the compensation strip running under the ceiling. If the wardrobe has perfectly sealed fronts fitted with brush seals, machining discreet oblong slots at the top and bottom of the carcass prevents the ambient air from stagnating without spoiling the appearance of the project.

Lighting must be planned from the cutting of the panels at the bench. Surface-mounted LED strips are not acceptable on quality work: they must be recessed in anodised aluminium profiles grooved flush into the vertical edges or under the fixed shelves. The aluminium profile provides a mechanical holding function but also acts as a heat sink, which is essential to preserve the life of the adhesive and the component. The recess machining must direct the light flow towards the inside of the carcasses at 45 degrees to light the front of the garments without dazzling the user. Holes for low-voltage conductors must be made in the workshop in the intermediate uprights, with the transformer housed in a ventilated void or an accessible plenum, in accordance with the coordination rules with the electrician.

Handling disagreements and technical rework after assembly

When a made-to-measure wardrobe is delivered, disputes almost always arise from a gap between the client's clothing habits and the internal volumes actually executed. Wide hangers whose sleeves rub against the sliding door dampers, winter coats that lose their fold on an intermediate shelf, or a short hanging rail that squashes the hems of jackets: the joiner is immediately faced with usage complaints. Faced with such disputes, the site foreman must proceed methodically to identify whether the problem stems from a dimensioning error in the workshop or from an unstated need.

The first reflex is to examine the execution drawing countersigned before manufacture. If the drawings stated a usable carcass depth of less than 550 millimetres without the client having measured the practical consequences, the joiner's professional liability is directly engaged under their duty to advise. If, on the other hand, the initial usage sheet and the approval form explicitly mentioned these geometric restrictions in order to work around a passage constraint in the room, the changes then constitute additional work that can be invoiced in accordance with the contractual provisions of the SIA 118 standard and the Code of Obligations (CO).

  • Replace a transverse rail with a system of longitudinal pull-out rails when the depth of the carcass prevents the doors from closing over standard hangers.
  • Reposition the shelf supports on the standardised 32 millimetre grid to recover the 1100 to 1200 millimetres needed under the short hanging rail.
  • Stiffen shelves with a span of more than 900 millimetres that sag under load by fitting an aluminium stiffening profile under the panel or by gluing a solid timber edge strip to the front edge.

Frequently asked questions

What net usable depth should be reserved for hanging suit jackets on hangers?

To hang men's jackets properly without crushing the shoulders against the panels or doors, allow a net usable depth of 550 to 600 millimetres. For sliding doors, add 80 to 100 millimetres to house the tracks and the overlap of the doors, which brings the total size of the unit to 650 or even 700 millimetres. Below 500 millimetres of usable depth, switch to an axial pull-out hanging rail.

How can clothing shelves be prevented from sagging over time?

The deflection of a shelf depends on its span, its thickness and the applied load. With 19 millimetre wood-based panel, limit the clear width to 800 millimetres for piles of jumpers or heavy linen. Beyond that, up to 1000 millimetres, switch to a thickness of 25 millimetres or incorporate a metal stiffener under the shelf. Also fix a batten to the back of the carcass to relieve the side shelf pins.

What hanging height should be provided between two superimposed rails?

To stack two rows of short hanging reserved for shirts and jackets, allow at least 1050 to 1100 millimetres of clear space under each tube. The upper rail is generally placed between 2000 and 2100 millimetres from the finished floor, which leaves about 1000 millimetres at the lower level without the garments touching the bottom of the unit. For users, installing an articulated wardrobe lift compensates for great heights.

How can LED lighting be integrated into the carcasses without overheating the unit?

Interior lighting is installed using LED strips recessed in a groove machined in the underside of a panel or in the front upright. Always use extruded aluminium diffuser profiles, which dissipate the heat of the light strip and avoid heating the wood or the stored clothes. Provide a low-voltage power supply located remotely in a ventilated niche or in the plinth, and control the switching with contactless door-opening sensors.

Texts and standards cited

  • norme SIA 118General conditions for the execution of construction work

In the same section