Skip to content
Website
🧱 CFC 273Claddings, skirting boards and parquet installationChapter 1 of 10 in the section

Perimeter gap: width, walls, thresholds and pipes passing through

By the end of this chapter, you will be able to size and provide the perimeter gap of a glued or floating parquet floor according to standard SIA 253. You will be able to neutralise the critical blocking points at door frames, door thresholds and heating riser pipe passages to prevent any lifting in summer climate conditions.

Key takeaways

  • Standard SIA 253 requires a free movement margin all around the perimeter of the parquet floor.
  • A single radiator pipe fitted tightly without clearance blocks the expansion and lifts the whole floor.
  • The minimum perimeter gap must be calculated according to the total width of the room.
  • Temporary spacer wedges must be removed before the skirting boards are nailed or glued.

The kinematics of summer swelling and the sizing of the perimeter gap according to standard SIA 253

Wood remains a living, hygroscopic material. During the summer period in French-speaking Switzerland, unheated ambient air frequently reaches a relative humidity above 70 %. Solid or engineered parquet absorbs this atmospheric moisture, which causes a tangential and radial dimensional widening of the boards. If this natural movement meets a rigid obstacle along the walls, the mechanical stress accumulated across the entire surface is released at the point of least resistance: the parquet detaches from the substrate or buckles upwards, forming a spectacular dome in the centre of the room.

Wooden floor coverings must be able to undergo, without hindrance, the foreseeable dimensional variations due to ambient climatic fluctuations. Sufficient perimeter and intermediate expansion joints must be provided in relation to all fixed building elements.

Norme SIA 253

To avoid this structural defect, the accepted rule of the trade, as codified by professional guidelines and standard SIA 253, is to provide a continuous empty space between the last board and any raw masonry, plasterboard lining or vertical masonry element. This gap must absolutely remain free of sawing waste, dry mortar or hardened adhesive before it is concealed by the skirting board.

Recommended perimeter gap width according to the extent of the work
Room span perpendicular to the grainType of installationMinimum perimeter gapRequired skirting board overlap
Up to 4 metresFully glued8 to 10 mm15 mm minimum
From 4 to 8 metresFully glued10 to 12 mm18 mm minimum
From 8 to 10 metresGlued or floating12 to 15 mm20 mm minimum
More than 10 metresFloating or gluedIntermediate dividing joint mandatorySuitable joint cover profile

Treatment of singular points: door reveals, thresholds and collars around heating pipes

The lifting of a parquet floor does not always come from a general omission along the main walls. In the majority of expert assessments of summer damage, the gap was correctly provided over 95 % of the perimeter but nullified by a single hard point. A central-heating riser pipe enclosed to the millimetre, a door frame base fitted too tightly or a door stop plugged through the board turns the surface into a rigid, locked plate.

  1. Clearing the feet of door frames and door casingsTrim the bottom of the timber door jambs with an oscillating saw placed on an offcut of board and its underlay. The parquet must be able to slide freely under the door frame by at least 8 millimetres without vertical friction.
  2. Drilling the pipe passagesMark the exact axis of the pipe. Drill a pilot hole with a flat bit or a hole saw with a diameter at least 16 to 20 millimetres larger than that of the metal tube. Then make a trapezoidal or 45-degree bevelled cut behind the pipe so that the piece of wood can be reinserted without creating a blockage.
  3. Fitting the concealing collarGlue the cut-out rear piece only to the edge of the adjacent board, never fix this piece against the pipe nor apply polyurethane adhesive in the annular gap. Conceal the remaining space with a double or single wooden or plastic rosette clipped around the tube.
  4. Transition under a door thresholdThe parquet must absolutely be interrupted between two rooms that are heated or ventilated differently. Place a dividing joint under the axis of the closed door leaf, ensuring a gap of at least 10 millimetres, covered by a mechanical threshold bar screwed only into the screed.

Mechanism of dome-shaped lifting and location of blocking points

The lifting of a parquet floor in the middle of a room occurs almost systematically between July and September. During this period, the indoor air records a high relative humidity, often between 65 % and 75 %. In accordance with standard SIA 253, solid wood or the balancing layer of a multilayer board absorbs this ambient moisture to reach equilibrium, which results in an unavoidable transverse expansion. If the parquet finds no free space at the perimeter, axial compressive stresses build up along the edge lines. When the force exerted exceeds the mechanical crushing resistance or the adhesion of the underlay, the assembly gives way by buckling: the floor detaches from the substrate and forms a characteristic hollow dome, springy underfoot.

The expansion failure is only rarely global; it is often the result of localised restraint that transfers all the stresses onto the rest of the span. A forgotten strip of cloth, a plaster residue fallen behind the skirting board or a water supply pipe enclosed without sufficient tolerance is enough to block an area of several tens of square metres.

Typology of the blocking points responsible for dome-shaped lifting
Singular zoneFrequent execution defectMechanical effect in humid periodsFinding on dismantling
Heating pipeworkHole drilled to the exact diameter of the copper or steelPipe pinched by the edge of the wood pushing forwardMarks of intense friction or deformation of the copper tube
Door reveals and door framesBoard forced under the rebate with no lateral clearanceBlocking of the edge, forces redirected towards the centre of the corridorBoard edge crushed against the door casing or the sub-frame
Wall perimeterSkirting board nailed or glued simultaneously to the wall and to the parquetVertical restraint preventing horizontal sliding under the skirting boardCracking of the skirting board finish or tearing off of the facing
Perimeter grooveTemporary spacer wedges forgotten before fixing the skirting boardsTotal cancellation of the expansion allowance at the edgePlastic or wooden wedge jammed under high pressure stress

Decompression protocol and restoration of the perimeter gap on the construction site

Intervention on a lifted parquet floor does not necessarily require the complete removal of the work, provided that the tongue and groove or the clip-together joint has not suffered irreversible mechanical tearing. The aim is to release the tangential stresses by restoring a perimeter gap compliant with standard SIA 253, while keeping a gap width compatible with the thickness of the decorative skirting boards in place.

  1. Methodical removal of the covering elementsCarefully remove the skirting boards at the foot of the partitions as well as the threshold profiles. Locate, using a metal feeler gauge or a flexible rule, the zones where the parquet touches the masonry, the partitions or the door frames directly under stress.
  2. Identification and elimination of localised restraint pointsCheck each pipe passage. If the pipe restrains the board, remove the decorative rosette and cut an additional arc of a circle with an oscillating tool to free a gap of at least 5 mm all around the tube. Check that there are no screws passing through the door stops.
  3. Perimeter decompression cutSet the depth of a plunge saw on a rail or of a flush-cutting saw so that it is flush with the thickness of the covering without cutting into the screed or severing an underfloor heating mat. Recut the edge over a calibrated width to restore a clear gap of 10 mm from the raw wall.
  4. Checking the settling and restoring flatnessOnce the decompression cut has been made, the axial stresses relax and the dome settles back under its own weight. Apply moderate pressure in the centre of the room to check that the work rests perfectly flat on its underlay or its adhesive bed.

Damage inspection record, repair under warranty and responsibilities when removing

When the parquet lifts into a dome under the effect of summer humidity, the joiner must intervene methodically before the tongue and groove assembly suffers irreversible breakage. The first action is to remove all the skirting boards around the perimeter of the affected room in order to see the hard-contact zones. In most cases, the blocking does not concern the whole perimeter but is concentrated on one long wall or on a singular fixed point such as a radiator pipe or a door stop screwed through the floating wood.

  • Careful removal of skirting boards and transition profiles without damaging the wall paint, to check for the presence of the perimeter gap prescribed by standard SIA 253.
  • Precise location of friction points: use of a thin wedge or a feeler gauge to map the sections in total abutment against the masonry or the pipework.
  • Making a flush-cutting saw cut with a plunge saw on a rail or with a grooving router, set back 10 to 15 millimetres from the masonry, to restore the necessary freedom of movement.
  • Clearing the pipe passages with a jigsaw or an oscillating tool to recreate an empty collar of at least 10 millimetres around the metal.

Once the mechanical stress is released, the parquet generally settles back by itself within a few hours under its own weight. If the boards remain deformed or if the interlocking profile has been chipped under the axial thrust, replacing the damaged elements becomes unavoidable. The contractor's liability is assessed under the rules of the contract for work and services of the Code of Obligations (CO): the absence of a gap is an execution defect attributable to the installer. Where the gap originally provided was filled by a rigid acrylic sealant applied by another trade or by an unreported through-fixing of a wardrobe rail, a joint inspection record with the site management makes it possible to establish the origin of the blockage.

Frequently asked questions

How can I quickly check whether the lifting is caused by a wall or by a heating pipe?

Removing the perimeter skirting boards immediately reveals the lines under pressure. If the edges retain a gap of at least 8 millimetres everywhere but the dome peaks near a radiator, examine the pipe passages. A parquet trapping a pipe without an allowance of at least 10 millimetres creates a fixed pivot point. During summer swelling, the axial thrust is transferred to this point anchor, forcing the work to lift upwards.

Can I simply plane the bottom of the skirting boards to hide a swelling without cutting the parquet?

No, this attempt does not resolve the mechanical defect at all. Dome-shaped lifting results from a blocked expansion force that puts the joints under extreme tension. Planing the skirting boards does not eliminate the axial pressure, which will eventually shear the tongues or split the edge boards. The only solution compliant with the rules of the trade is to remove the skirting boards and recut the edges of the parquet to recreate the prescribed gap.

What should be done if the necessary perimeter gap exceeds the thickness of the skirting board provided in the tender?

If the width of the room requires a gap greater than the thickness of the prescribed skirting board, the joiner must report this dimensional conflict to the site management before installation. Several technical solutions exist: notching the bottom of the plasterboard so that the parquet can slide underneath, fitting a skirting board of larger section or adding a floor joint cover. The written agreement of the project management remains essential to validate the chosen variant.

Who bears the cost of repairs when the parquet lifts against a door frame installed without a gap?

The joiner installing the parquet must provide the expansion gap under the door frames and casings. If they abutted the boards directly against the wood of the frame without leaving the millimetres required by standard SIA 253, the defect is entirely their responsibility under the Code of Obligations (CO). They must recut the boards with an oscillating tool and replace the damaged elements at their own expense, including any finishing repairs.

Texts and standards cited

  • SIA 253Installation of glued and floating floor coverings, sizing of expansion joints and perimeter decoupling

In the same section