Skip to content
Website
🧱 CFC 273Claddings, skirting boards and parquet installationChapter 6 of 10 in the section

Lining a window reveal: sill, side panels, condensation and movement clearance

This chapter details the installation rules for interior window reveals for joiners in French-speaking Switzerland. You will know how to prevent defects caused by condensation on raw masonry, build in a perimeter clearance compliant with SIA 343 and ensure a stress-free mechanical fixing to guarantee the dimensional stability of the sills and side lining panels.

Key takeaways

  • Direct contact of a timber panel against uninsulated concrete causes detachment through condensation.
  • SIA 343 requires hygrometric variations to be taken into account in interior assemblies.
  • A perimeter clearance of at least five millimetres allows free expansion without pushing on the frame.
  • Fixing onto battens with slotted holes prevents cupping of the sills under thermal stresses.

Cold masonry and the causes of failure of glued sills

Fitting a sill or a reveal lining directly in contact with the structural work is one of the most frequent defects in interior joinery. When the window frame connects to a reveal in reinforced concrete or in clay brick that is not insulated on the inside, the surface temperature of the masonry drops drastically in winter. Fixing a wood-based panel or a solid sill glued over its full surface onto this cold substrate traps the room air and creates a critical thermal bridge.

Interstitial dew point
Temperature at which the water vapour contained in the indoor air condenses into liquid form on contact with a cold wall, saturating the adhesive and the underside of the timber lining.

The moisture of the heated air inevitably migrates towards the rear face of the lining. When this vapour meets the mineral substrate below the dew point, it liquefies. Water accumulates at the interface between the adhesive bead and the substrate. The polyurethane adhesive or the assembly sealant loses its adhesion through saponification or mechanical delamination of the plaster. At the same time, the underside of the timber absorbs this liquid water while its upper face remains dry in the heated air of the room.

SIA 343 reminds us that timber and wood-based structures must be designed to absorb without damage the dimensional variations inherent in the Swiss indoor climate. In winter, the indoor air dried by heating brings the moisture content of the timber down to between 7% and 9% on its visible face, whereas the moisture content at the contact with the cold masonry can exceed 18%. Without intermediate insulation or ventilation, this asymmetry inevitably leads to failure of the work.

  • Rapid degradation of the bonding agent under the combined action of standing water and the alkalis of the concrete.
  • Development of mould not visible behind the panel, degrading the hygienic quality of the air.
  • Axial thrust against the window frame, causing sashes to jam or plaster to crack.
  • Failure of the mitre joints between the horizontal sill and the vertical side panels of the reveal.

Decoupled fixing, stress-free wedging and base seal

To stabilise a reveal lining durably, the joiner must absolutely decouple the panel from the cold structural work and provide a perimeter expansion clearance. The fixing must never restrain the timber element, but allow it to slide along its axes of shrinkage and swelling. This freedom of movement is ensured by an intermediate thermal packing and a mechanical fixing on slotted holes or sliding fixings.

  1. Interposing a thermal breakPlace a rot-proof resilient strip or a thin rigid insulation on the raw sill to cut the direct contact between the lining panel and the cold masonry.
  2. Installing the substructureFix battens or support blocks made of treated timber or composite material, levelled with flat shims, leaving a decoupling air gap of at least ten millimetres.
  3. Stress-free fixingScrew the sill from underneath onto the battens through slotted holes of at least eight millimetres, allowing the timber to slide axially without rigid blocking.
  4. Providing the clearance and the backing cordLeave a free perimeter clearance of five millimetres against the window frame and insert a backing cord of closed-cell extruded polyethylene foam.
  5. Extruding the flexible jointApply a neutral silicone or hybrid polymer elastomer sealant against the window profile, tooled smooth without adhering to the bottom thanks to the cord, ensuring two-sided adhesion.
Installation parameters for interior reveal lining
Assembly componentMaterial or dimensionTechnical function
Clearance at the bottom of the rebate5 mm minimumFree expansion without pushing on the frame
Backing cordClosed-cell PE cordRear adhesion break for a two-sided joint
SealantNeutral silicone or MS polymerAirtightness without rigid mechanical stress
Underside drillingSlotted holes 8 mm wideAllows the panel to shrink and swell
Underside of the sillBalancing layer or varnishBalance of the surface stresses of the substrate

The finishing of the vertical side panels follows the same principle: the reveal panels rest on the sill with a clear clearance of two to three millimetres sealed by a flexible joint, or fit into a groove cut under the top rail. Respecting these decoupling measures and eliminating rigid bonding on cold walls avoids any warranty claim after the first winter of use.

Sizing the perimeter clearances and installing the flexible backing joint

The lining of a window reveal tolerates no rigid connection against the structural work or the existing frame. Under the effect of the temperature differences between the heated indoor environment and the cold exterior masonry, warm and humid air infiltrates as soon as airtightness is lacking. On reaching the dew point in contact with concrete or calcium silicate brick, the vapour condenses into liquid water on the hidden face of the panel. If the sill or the side panels are wedged tight or sealed in without tolerance, the panel absorbs this moisture, swells in width and generates lateral thrusts that cause buckling of the piece or tearing out of the fixings.

To absorb the inherent movement of the solid timber or wood-based panel (moisture-resistant MDF or plywood) and prevent indoor air from reaching the residual thermal bridge, the bottom connection requires a flexible sealing profile with a dual function. The sill is cut with a nominal setback ensuring a clear gap all around its perimeter. At the bottom of this recess, against the groove of the window frame, the tradesperson presses in a closed-cell polyethylene foam backing cord. This cylindrical cord limits the extrusion depth of the sealant, ensures a contact surface limited to two opposite faces and allows stretching without tearing during dimensional variations.

Execution parameters for reveal clearances and elastomer beads
Lining elementRequired perimeter clearanceBacking cord diameterRecommended sealant type
Solid timber sill (oak, beech)6 to 8 mm at the bottom, 4 mm at the sidesØ 10 mm (compressed by 25%)High-modulus hybrid polymer sealant
Composite panel / MDF sill5 mm at the bottom, 3 mm at the sidesØ 8 mm (compressed by 25%)Solvent-free neutral alkoxy silicone
Side panel against masonry4 to 6 mm around the perimeterØ 8 mmPaintable elastic acrylic or hybrid
Suspended reveal lintel5 mm at the underside of the lintelØ 8 mmZero-shrinkage hybrid polymer

Connecting side panels and lintel: stress-free mechanical fixing and air gap

Assembling the vertical side panels with the reveal sill and the lintel panel must cope with the irregularities of the cold masonry without restraining the timber. An installation locked by full-surface bonding or rigid nailing in the corners transmits moisture by capillarity and prevents the natural seasonal deformations. The fundamental principle is a stress-free mechanical fixing, made by means of treated timber battens or metal brackets plugged into the structural work, fitted with slotted holes oriented in the direction of shrinkage or swelling.

  • Interposing a rot-proof resilient strip under the wedging battens to cut the thermal bridge and the direct contact with the raw concrete.
  • Using countersunk-head screws in slotted holes with wide metal washers, without tightening to the point of blocking, so that the panel can slide.
  • Providing a ventilated air gap of 10 to 15 mm at the rear face of the side panels to prevent confinement of the residual relative humidity.
  • Mitre or removable rebate joint between the sill and the side panels, assembled with longitudinal biscuits or cam fittings allowing a lateral clearance of 1 to 2 mm.
  1. Marking out and checking plumbCheck the flatness of the masonry reveal, identify the low points and mark the position of the packing shims to provide the rear air gap.
  2. Fitting the brackets with slotted holesDrill the masonry, insert universal plugs and screw on the mechanical fixing brackets without tightening them to the maximum torque.
  3. Engaging the side panels and the sillPresent the reveal assembled dry, check the continuous 5 mm setback from the window frame and fix the panels onto the slotted slides.
  4. Sealing the bottom of the rebatePush the closed-cell foam cord to the bottom of the joint with an insertion wheel, then tool the elastomer sealant smooth without overrunning onto the visible edges.

Defects in service: repairing a detached sill and treating residual moisture

Detachment of a reveal sill fixed in a full bed of mortar or by direct rigid bonding onto the structural work is a classic defect in winter. When the sill wall or the concrete under the window has a surface temperature below the dew point of the indoor air, the vapour migrates and condenses under the timber panel. The masonry substrate transmits this moisture to the panel by capillarity. The panel's balance is broken: the underside swells, the panel bows upwards and the adhesive bond tears off. To correct this defect in accordance with the requirements of SIA 343, the joiner must refuse any superficial re-bonding and completely redo the installation principle.

  1. Careful removal and remediationCut the finishing beads with a cutter so as not to tear off the adjacent plaster. Remove the sill without forcing on the window's sill member. Completely remove the residues of plaster, mortar or old sealant. Check the moisture of the raw substrate: the masonry must be dry before any new work. If a major thermal bridge is found, insert a strip of rot-proof incompressible insulation on the sill wall.
  2. Packing and mechanical fixingFit transverse rot-proof shims at least six millimetres thick to create a continuous air gap under the sill. Fix the sill mechanically without stress using screws engaged in pre-machined slotted holes, or sliding metal brackets. This arrangement allows the natural hygrometric expansion and shrinkage of the material without generating mechanical shear stress.
  3. Flexible sealing on a backing cordPosition a round extruded polyethylene backing cord against the bottom rail of the frame, sized for twenty per cent compression. The backing cord ensures two-sided adhesion of the sealant without bonding to the window frame. Apply a neutral silicone or polyurethane elastomer sealant over the full width of the reveal to perfect the airtightness while absorbing the differential movements.

Frequently asked questions

Why does a solid timber reveal sill systematically cup if it is glued onto raw masonry?

Timber exchanges moisture with its environment to reach hygroscopic equilibrium. In direct contact with cold masonry prone to interstitial condensation, the underside absorbs liquid water and swells. The upper face, exposed to the heated ambient air of the room, keeps a clearly lower moisture content and shrinks. This hygrometric asymmetry produces a concave or convex curvature that a simple adhesive bed cannot contain, resulting in mechanical tearing off from the substrate.

What minimum perimeter clearance must be provided between the sill, the side panels and the window frame?

A nominal clearance of three to five millimetres should be provided on each edge and at the bottom of the reveal. This space compensates for the hygrometric swelling of the panel in accordance with the rules of SIA 343 and prevents jamming against the masonry. At the bottom, this clearance also allows a foam backing cord to be inserted before extruding the flexible sealant. Reducing this clearance to zero exposes the work to blistering of the reveal when the relative humidity rises.

How do you make a stress-free fixing on an uneven sill substrate?

Timber cleats or adjustable synthetic bearing shims fixed to the concrete substrate are used. The sill rests freely on these ventilated support points. It is held from underneath using brackets fitted with slotted holes in the direction perpendicular to the window, or by adjusting screws with cushioning washers. This mechanical guidance prevents lifting while letting the panel slide freely during the seasonal dimensional variations of the work.

Why must expanding polyurethane foam be prohibited under an interior window sill?

Injecting expanding foam under a sill carries a major risk of uncontrolled residual thrust that deforms the panel within a few hours. Moreover, standard polyurethane foam provides no effective water vapour barrier on cold masonry. If condensation occurs in contact with the raw concrete, the foam traps this moisture against the underside of the timber without ventilation, promoting biological rot of the panel and the side panels.

Texts and standards cited

  • SIA 343Doors and interior joinery elements - Thermo-hygrometric requirements and dimensional behaviour of linings

In the same section