Skip to content
Website
🧱 CFC 212Facade scaffolding: components, erection and dismantlingChapter 7 of 10 in the section

Bypassing Balconies and Projections: Offsets, Brackets and Decking Continuity

On complex facades, balconies and recesses require precise adaptations of the structure. You will learn how to install extension brackets, manage standard offsets, and close every void to guarantee decking continuity and guardrail compliance in accordance with standard SN EN 12811 and federal regulations.

Key takeaways

  • Extension brackets widen the working platform towards the facade without weakening the main bay.
  • Any offset of a standard alters the load path and demands immediate reinforced ties.
  • Decking continuity prohibits any gap exceeding the permissible limits beneath the brackets.
  • At projections, lateral closure requires a rigid, complete perimeter guardrail.

Installation of Brackets and Management of Axial Offsets

Architectural projections such as access balconies, bow windows, and balcony slabs break the standard vertical alignment of a facade scaffolding. The scaffolder must adapt the structure without disrupting the circulation of the finishing work trades. Two primary strategies are available on site: completely shifting the bay outwards or maintaining a straight main grid equipped with extension brackets directed towards the face of the building.

Standard SN EN 12811 defines the performance and general design requirements for service scaffolding, including the stability of cantilevered widenings, the dimensioning of working platforms, and deflection limits under service loads.

norme SN EN 12811

Erection using internal brackets represents the most efficient solution for accommodating an isolated balcony. Tubular or drop-in brackets lock onto the main standards on the wall side. This arrangement extends the working platform as close as possible to the render or the underside of the concrete. As soon as a bracket is installed, it generates a torsional moment and additional tensile force on the couplers and bracing diagonals of the bay.

  1. Checking spans and clearance gaugesMeasure the exact balcony projection with a tape measure to select the appropriate standardized bracket width without creating interference with masonry balustrades.
  2. Locking cantilever bracketsSecure the brackets to the scaffolding standards using wedges or right-angle couplers torqued with a torque wrench according to the manufacturer's specified values.
  3. Compensating tiesInstall a short tie using anchor screws or expanding anchors into sound reinforced concrete, directly at the node receiving the bracket, to neutralise horizontal forces.
  4. Laying offset platform unitsInsert the lockable scaffold decks, ensuring that the anti-lift wind latches engage mechanically onto the supporting transoms.

Decking Continuity and Guardrail Closure at Facade Steps

Transitioning from a standard bay to a widened bay around a projection creates risks of platform discontinuities. Since a facade rarely presents a continuous line, scaffolders are required to eliminate any gap where a worker could trip or drop tools. Decking continuity must be absolute: no residual gap may remain between the main platform, the bracket decking, and internal re-entrant corners of the masonry.

Decking continuity
Seamless arrangement of platform decks ensuring a flush, tight-fitting, and self-locking walking surface, eliminating the risk of tipping tools and hazardous level changes between adjacent bays.
Constructive protective measures according to projection configurations
Encountered configurationAdaptation systemEdge treatmentClosure requirement
Continuous wrap-around balconyFull axial offset using widened framesContinuous standard platform unitsPerimeter guardrail on the outside
Single isolated balconyHop-up brackets on internal standardsInfill decks with sheet-metal bridging platesLateral closure at the ends of the offset
Facade recess or projectionOffset bay with bridging lattice beamsEdge-to-edge overlap without stepsStop-end guardrail and end toe-boards
Clearance beneath a loggiaShort brackets and through-wall tiesAdjusted decking tight to the finished lineFull face protection facing the void

At the step created by a balcony, the linear geometry of the scaffolding is partially interrupted. The Construction Work Ordinance specifies the geometric and collective fall protection rules required in these critical zones. In accordance with art. 22 OTConst, perimeter guardrails must comprise a top rail with its upper edge at least 100 cm above the working surface, at least one intermediate rail, and a toe-board of at least 15 cm, with a maximum clearance of 47 cm between these elements.

To bridge triangular or rectangular spaces at balcony corners, the use of dedicated aluminium infill decks or chequer plate adaptations secured with clamps is required. Makeshift packings using loose, unfixed 27 mm formwork boards are strictly prohibited, as construction site vibrations quickly dislodge such loose components. In the event of a complex configuration requiring non-standard adaptations not covered by manufacturer instructions, art. 29 OTConst states that equivalent protective measures must be defined in writing by consulting an occupational safety specialist prior to commissioning.

Load Transfer and Specific Ties Beneath Projection Brackets

The cantilever introduced by an extension bracket completely alters the load path of a scaffolding bay. As soon as the working platform extends beyond the alignment of a balcony or a projecting eaves overhang, the offset generates an overturning moment acting directly on the facade standards. Standard SN EN 12811 requires these assemblies to be dimensioned according to the required load class, taking into account the tensile and compressive forces induced in the supporting standards and diagonal braces.

Structural implications of cantilever brackets by configuration
Projection configurationForces generated on the structureRequired constructive arrangement
Internal bracket (width 0.36 m)Moderate tension on the upper tie, compression on the standardStandard tie at the scaffolding node at every level
External bracket (width 0.73 m)High tension on the tie, local bending on the standardDoubled ties at bracket level and tie rod beneath the deck
Lattice beam cantilever (> 1.00 m)Heavy point load transfer to adjacent standardsDoubled standards, transverse diagonals, and load capacity verification

The bending moment induced by extension brackets requires rigorous bracing by means of tubular diagonals clamped beneath the corner couplers. When the offset exceeds the useful width of a standard 0.73 m platform, the scaffolding can no longer rest on simple isolated brackets: it requires vertical propping down to the ground or main aluminium lattice beams secured to the main standards.

Closure of Offsets and Front Guardrails at Re-entrant Corners

The step created to bypass a balcony systematically breaks the line of protection. This staggered offset opens a gaping void downwards as soon as the structure steps away from the facade line. Under art. 22 OTConst, safety mandates the installation of a top rail with its upper edge at least 100 cm high, an intermediate rail, and a toe-board of at least 15 cm, with a maximum spacing of 47 cm between elements.

  1. Measuring and fitting end stop guardrailsAt balcony steps, secure the platform edge with a complete transverse guardrail fastened with right-angle couplers to the cantilever standards.
  2. Closing re-entrant corners against the projectionIf the residual gap between the offset standard and the balcony masonry exceeds 30 cm, install comprehensive lateral protection to eliminate any risk of falling on the inside.
  3. Fitting tool-retaining toe-boardsFit timber or steel toe-boards along the entire inner and outer perimeter of the return to prevent falling materials in accordance with the requirements of OTConst.

Passageway continuity must remain seamless: no level change exceeding 25 mm may remain across the axial offset. If system guardrails cannot be locked onto standards due to an irregular bay length, assemble 48.3 mm diameter galvanised steel tubes using fixed double-bolt couplers, adjusted to the millimetre around the cantilevered slab.

Managing Facade Discrepancies and Handover of Offset Structures

On renovation or conversion construction sites, the actual geometry of the structural work presents surprises: out-of-plumb balcony slabs, thicker external insulation than expected, or non-demountable architectural brackets. These obstructions frequently require adjustments to the initial layout plan. The scaffolder cannot improvise a cantilevered offset without verifying the structural behavior of the scaffolding.

Standard SN EN 12811 specifies performance requirements and calculation methods for temporary work equipment. Any erection deviating from the standard configuration approved by the supplier requires a specific structural calculation for tie sizing. In accordance with art. 22 OTConst, continuous edge protection remains mandatory at steps: top rail at least 100 cm above the working surface, intermediate rail, and toe-board of at least 15 cm.

  1. Inspection and notificationIf a geometric discrepancy prevents the compliant installation of an extension bracket, halt erection of the affected bay. Report the discrepancy to site management.
  2. Structural adaptationRecalculate tensile forces on adjacent ties beneath the balcony and double up couplers or tie tubes if load transfer demands it.
  3. Temporary securingBlock access to the interrupted deck using an end-stop guardrail and warning signs prohibiting passage until the bridging deck is fully installed.
  4. Formal handover inspectionVerify that no gap exceeds permissible tolerances, record adaptations in the inspection handover report, and attach the green scaffold release tag.

When the gap between the facade line and the decking exceeds safety limits after bypassing a projection, installing a complete internal guardrail or an infill bracket is mandatory prior to releasing the scaffold to the finishing work trades.

Frequently asked questions

How can decking continuity be ensured when a balcony bracket requires an offset of the standards?

A system-compatible extension bracket is used, fixed at platform level. If prefabricated platform decks do not cover the entire void, bridging is created using squared timber baulks at least 45 mm thick, securely clamped with brackets or wedge couplers. No residual gap may remain, preventing any risk of tipping or tripping.

What solution should be chosen for guardrails at a significant facade recess?

The step creates a lateral void requiring a transverse stop-end guardrail. This assembly is erected on tubular standards linked to the main frames with right-angle couplers. It strictly includes a top rail, an intermediate rail, and a return toe-board across the entire depth of the projection to prevent falls to the inside or the outside of the offset structure.

Can restraining ties be fixed directly into the underside of a concrete balcony?

Yes, provided the concrete quality is verified and edge distances specified in the technical sheets for mechanical or chemical anchors are observed. Because wind forces cause alternating pushing and pulling loads, push-pull screw props within window reveals or through-tubes are often preferred to avoid spalling the slab edge of the existing balcony.

What should be done if the residual passage width beneath a balcony is restricted by a bracket?

Standard SN EN 12811 specifies a minimum clear width based on the selected scaffold class, generally not less than 50 cm clear of obstructions. If the offset restricts usable width excessively, an external cantilever bracket must be fitted to reroute circulation, or a separate access bay with independent stair towers must be erected to bypass the pinch point at the projection.

Texts and standards cited

  • SN EN 12811Temporary works equipment - Scaffolds: Performance requirements and general design
  • OTConst art. 22Requirements for perimeter guardrails: top rail with upper edge at least 100 cm above the working surface, at least one intermediate rail, toe-board of at least 15 cm, maximum clearance of 47 cm between elements

In the same section