Skip to content
Website
🧱 CFC 212Facade scaffolding: components, erection and dismantlingChapter 6 of 10 in the section

Erecting by lifts: the order protecting the erector step by step

This chapter details the chronological sequence for erecting façade scaffolding lift after lift. You will learn to use the temporary advance guardrail to operate constantly under collective protection, to follow the structural assembly order of frames, decks and diagonals, and to cordon off the ground exclusion zone effectively beneath vertical handling operations.

Key takeaways

  • The erector systematically installs collective protection before accessing the upper working lift.
  • OTConst art. 26 requires façade scaffolding as soon as the fall height exceeds 3 m.
  • The rigorous assembly sequence ensures squareness, intrinsic stability and the transfer of erection loads.
  • The ground zone remains strictly prohibited to any outside person during lifting operations.

Erecting under collective protection using the advance guardrail

On a building construction site, the scaffolding erector works in a unique situation: they create the safe working platform intended for other trades, which exposes them to the fall hazard before permanent protections are installed. To eliminate the risk of falling from height during this critical phase, the protected erection method has become the professional standard in Switzerland. The technical principle relies on anticipating protection: no erector must step onto decking without a guardrail already positioned to block the external fall edge.

Façade scaffolding must be installed as soon as the fall height exceeds 3 m; the top guardrail must project at least 80 cm above the edge of the highest area presenting a fall risk (100 cm if the guardrail is less than 60 cm from the edge).

art. 26 OTConst

On-site implementation is achieved primarily through two technical processes: the temporary advance guardrail and the permanent guardrail installed in advance. The temporary guardrail consists of a pole or a lightweight aluminium frame, handled from the lower platform that is already secured. The erector attaches this telescopic device to the standards of the upper lift before climbing up. Once up, they work sheltered behind this temporary barrier to bolt the permanent top guardrails, intermediate guardrails and toeboards, then detach the temporary equipment to transfer it to the next lift. More recent systems directly incorporate permanent guardrails erected from below, eliminating any handling of temporary equipment.

Component sequence by bay and ground zone cordoning

Erecting a bay tolerates no improvisation in the sequence of actions. Each metal component fulfills an immediate mechanical role in bracing or load transfer. Reversing the placement of a diagonal or delaying the installation of a deck weakens the structure under the self-weight of supplied materials and compromises overall squareness.

  1. Installing access and decksFrom the secured lower lift, working decks are raised and engaged onto the frame transoms. The access trapdoor with integrated ladder is positioned in the dedicated bay to allow internal ascent without passing on the outside of the structure.
  2. Setting up upper protectionBefore accessing the newly decked lift, the erector installs the temporary advance guardrail or pivots the permanent guardrail from below using the dedicated tool.
  3. Ascent and locking of vertical framesThe erector takes the internal ladder, emerges onto the protected deck, then fits the standards or vertical frames of the lift over the spigots. Safety locking pins are inserted immediately to prevent any accidental disengagement.
  4. Bracing and tiesFaçade diagonals are attached to ensure triangular rigidity of the bay. Façade ties required by the structural calculations are drilled and installed as the structure rises, without waiting for the complete completion of the lift.
  5. Finalising the permanent guardrailInstalling the top guardrail, intermediate guardrail and edge toeboard to complete the collective protection system of the working surface.

Throughout the duration of manoeuvres, the ejection or accidental fall of a metal component — scaffolding spanner, coupler, pin or bolt — presents a fatal hazard. The Construction Works Ordinance requires ensuring the safety of walkways and workstations against falling objects. The contractor responsible for erection establishes a strict exclusion zone at the base of the scaffolding.

Organisational measures for the ground zone according to site configuration
Structure configurationExclusion systemAccess control
Enclosed courtyard or construction site footprintRigid demarcation using light site barriers and prohibition signsAccess reserved exclusively for erection crew material handlers
Adjacent pavement or public walkwayCovered walkway with impact-resistant, tight decking or complete diversionTotal prohibition of pedestrian routing without protective roof
Immediate proximity of other tradesCoordination of work schedules and rigid barrier tape with warning signsMandatory halt of overhead lifting during approved, exceptional crossings

Vertical transition and installing the permanent guardrail under protection

Accessing the upper lift constitutes the critical phase of erection. As soon as the upper working deck is installed from the floor below, the erector must access it to install the permanent structure without ever being exposed to the fall edge. This ascent is performed exclusively via the access trapdoor integrated into the access ladder, under the continuous protection of the prior advance guardrail deployed from the lower lift.

  1. Unlocking and passing through the trapdoorThe erector lifts the trapdoor of the access deck with one hand while maintaining three points of contact on the ladder rungs. The trapdoor is lowered immediately after passage to recreate a continuous floor before any handling of materials.
  2. Positioning vertical frames or standardsStanding on the decking secured by the temporary guardrail, the erector fits the façade frames or tubular standards over the spigots of the lower lift. Safety locking pins are engaged manually to prevent any accidental uplift.
  3. Installing the permanent top and intermediate guardrailsPermanent collective protection components are locked onto the brackets or wedges of the standards. Assembly is carried out from inside the bay outwards, without leaning the torso beyond the structural line.
  4. Installing the toeboard and removing temporary protectionThe toeboard, at least 15 cm high, is slid into its base retaining pockets to close off the floor opening. The temporary advance guardrail can then be unhooked or pivoted towards the upper lift to start the next cycle.
Visual and dimensional check before clearing the working lift
ComponentRequired positioningWork stoppage criterion
Top guardrailTop edge at least 100 cm above the deckHeight below mark or missing wedge lock
Intermediate guardrailMaximum vertical gap of 47 cm relative to guardrailsMissing or deformed intermediate guardrail
Edge toeboardHeight of at least 15 cm, flush with the deckingVertical play exceeding engagement tolerances
Working deckFull coverage of bay width without tipping riskPresence of an uncovered gap or bent claw

Upward progress, synchronous tying and area security

According to OTConst art. 26, façade scaffolding must be installed as soon as the fall height exceeds 3 m; the top guardrail must project at least 80 cm above the edge of the highest area presenting a fall risk (100 cm if the guardrail is less than 60 cm from the edge). For the scaffolding erector, this threshold dictates a strict tying pace: vertical progress must never outpace the anchor layout defined by the manufacturer's structural calculations.

Each new lift reached requires immediately securing the framework to the masonry or supporting structure. Scaffold ties fitted with right-angle couplers are fixed to the inner standards, directly below the node connection of the decks. Erecting an additional lift on a structure whose lower lift is not anchored compromises overall stability against wind tension and compression forces.

  • Installation of anchor eyes exclusively in reinforced concrete or solid brick, with verification of anchor bolt tightening torque.
  • Systematic installation of bracing diagonals in end bays and according to the structural pattern as soon as standards are positioned.
  • Verification of standard verticality using a spirit level prior to final tightening of tie couplers.
  • Strict maintenance of ground access prohibition as long as the upper lift is not fully enclosed and locked.

Handling erection anomalies and stopping work during lifting

On façade scaffolding, erection by lifts imposes strict geometric discipline. When a component refuses to engage, when an anchor fixing fails in the masonry or when a third party crosses the ground cordoning, the erector stops work immediately. Continuing erection without resolving an alignment fault or anchor failure transfers hidden mechanical stresses to upper floors.

  1. Lifting stoppage and securing materialsLower unlocked components onto the stable floor below. Leave no frame, diagonal or deck in unstable equilibrium or suspended from a lifting winch.
  2. Checking tying and verticalityCheck spirit level and coupler tightness on the standards of the preceding lift. Under OTConst art. 26, façade scaffolding must be installed as soon as the fall height exceeds 3 m; the load-bearing structure must therefore remain perfectly rigid and tied progressively during erection.
  3. Clearing the hazard zoneIf the exclusion perimeter at the base of the structure is breached by other trades, suspend all high-level handling until physical barriers on the ground are completely restored.

The team leader logs any geometric discrepancy or abnormal resistance of the anchor substrate. Under OTConst art. 6, wearing a safety helmet is mandatory during scaffolding erection and dismantling. In the event of an intractable technical blockage using standard components, the erector stabilises the bay using temporary bracing before consulting the site management.

Frequently asked questions

How should the advance guardrail be installed if an obstacle on the façade obstructs its pivoting?

When the geometry of an opening, balcony or eaves blocks the deployment of the telescopic advance guardrail, the erector never steps onto the unsecured lift. They instead use personal fall protection equipment anchored to an approved structural anchor point, first install the permanent guardrails at the statutory height from a protected position, and then access the upper deck once collective protection is closed.

What should be done if another trade opens the ground cordon during erection?

The erector immediately stops lifting metal components and halts all handling on the decks. They challenge the personnel on the ground to warn them of the fatal risk of falling objects. High-level operations resume only after unauthorized personnel have fully cleared the area and the cordon is physically closed with rigid barriers or monitored barrier tape on the ground.

Can an additional lift be erected if the specified tie could not be drilled?

No. Erection by lifts requires synchronous tying of the structure. Erecting a lift without installing the planned ties creates a dangerous lever arm under wind loading or the weight of erectors. If drilling is impossible at the theoretical location, the erector must immediately carry out an alternative tie by clamping a load-bearing concrete element before continuing upward progress.

May an erector remove a temporary guardrail before locking the permanent guardrail?

Never. The protected erection principle requires absolute continuity of collective protection. The temporary advance guardrail, installed from the lower access lift, may only be removed or pivoted upwards once the permanent top guardrail, intermediate guardrail and toeboard are securely fixed to the standards of the new working lift, thereby ensuring the total absence of any unprotected side edge.

Texts and standards cited

  • OTConst art. 6requirement to wear a safety helmet during all work where workers may be endangered by falling objects or materials; helmet worn in any case during construction work until completion of the structural work, near cranes and earth-moving plant, during excavation, demolition, and scaffolding erection and dismantling (para. 2); helmet with chinstrap notably during work using fall protection equipment or rope access (para. 3).
  • OTConst art. 26façade scaffolding in building construction work: façade scaffolding must be installed as soon as the fall height exceeds 3 m; the top guardrail must project at least 80 cm above the edge of the highest area presenting a fall risk (100 cm if the guardrail is less than 60 cm from the edge) (para. 2).

In the same section