Skip to content
Website
🧱 CFC 212Decking, access and collective protectionChapter 5 of 10 in the section

Extension bracket: gain width on the facade side without losing protection

This chapter provides scaffolding erection teams with technical guidelines for correctly integrating extension brackets on the inner side. You will learn how to design the permissible load of cantilevered platforms, achieve rigid fastening to the main frames and maintain collective fall protection at offsets from the facade.

Key takeaways

  • Extension brackets increase the working area while altering load distribution.
  • Standard SN EN 12811 defines the mechanical strength and stability requirements of the system.
  • Rigid locking to the frame prevents any overturning or slipping of the bracket under load.
  • The gap between the widened platform and the facade must always comply with safety requirements.

Fastening and mechanical strength of extension brackets

Adding an extension bracket on the inner side brings the working platform closer to the masonry or provides a temporary storage area for finishing work trades. However, this offset alters the forces transmitted to the main structure. All component parts must meet the requirements of standard SN EN 12811, which governs the structural performance and general design of service scaffolding.

Erection demands absolute rigour when connecting to the vertical frame. Integrated spigots, half-couplers or locking pins must engage fully into the intended recesses. Poor alignment creates a leverage effect on the inner standard, reducing shear capacity and exposing the structure to permanent deformation under the stress of live loads.

Assembly requirements for brackets on the main frame
Inspection itemAcceptance criterionVerification action
Bracket supportFull contact on the frame nodeVisual inspection of positioning
Locking componentPin engaged or coupler fully tightenedManual check and test hammer tap
Deck levelnessFlush alignment without lips with main deckSpirit level check

Collective protection and continuity of safety at offsets

Installing a bracket on the inner side alters the distance separating the platform from the facade wall. When this gap exceeds the limit permitted by occupational safety, installing additional protective components becomes mandatory. Scaffolding erectors must adapt the system so that no hazardous gap remains along the working area.

The edge protection comprises a top guardrail at least 100 cm above the accessible surface, an intermediate rail and a toeboard of at least 15 cm.

art. 22 OTConst

If a setback in the masonry at a balcony or an opening creates a gap with a risk of falling from more than 2 m, legal provisions require the space to be closed. The Construction Work Ordinance specifies these obligations in art. 23 OTConst.

  1. Measurement of residual gapCheck the exact distance between the inner edge of the decking laid on the bracket and the finished wall face.
  2. Installation of inner guardrailsIf the gap exceeds the safety limit, install inner top rails, intermediate rails and toeboards on the bracket uprights.
  3. Check of endsClose bracket returns laterally using end guardrails to block any access to residual gaps.
  4. Acceptance of the extended platformEnsure each deck placed on the bracket is locked against uplift before handover.

Permissible loads and structural interaction according to standard SN EN 12811

Adding an extension bracket on the inner side alters the load distribution on the scaffolding standards. Standard SN EN 12811 defines the load-bearing capacity of scaffolding components and requires that any cantilever be included in the verification of the platform load class. The self-weight of the bracket, combined with the live load applied at the offset, generates an additional bending moment and shear force on the frame nodes.

At the tie level, the inner bracket increases the pull-out load on the upper line of fixings. The erection team must verify that the wall tie absorbs the additional tension induced by the leverage of the bracket arm.

Impact of inner bracket on forces and tying
Bracket widthTypical permissible live loadImpact on standardsTying requirement
30 cm (1 platform deck)According to Class 3 (200 kg/m²)Low additional normal forceVerified standard tying
60 cm (2 platform decks)According to Class 2 or 3Bending moment at frame nodeIncreased tie density on the level
Custom bracketAccording to specific structural calculationIndividual verification requiredThrough-ties or special anchors

Rigid fastening to the frame and maintaining collective protection

Fastening the bracket to the scaffolding frame is carried out using socket connections or compliant couplers. Precise positioning of locking pins or torque tightening of couplers prevents any tipping under load. The assembly must show no play likely to misalign the inner deck relative to the main deck.

  1. Inspection of attachment pointsCheck the condition of cups, frame pins and half-couplers before engaging the extension bracket.
  2. Laying inner platform decksInstall the extension decks and lock the anti-uplift devices to close the gap between the scaffolding and the masonry.
  3. Installation of inner guardrailsErector and foreman ensure that stop guardrails or inner rails are erected when the distance to the wall exceeds the permitted limit.

Erecting an inner bracket in no way exempts from installing collective protection. According to art. 22 OTConst, if the distance between the edge of the widened platform and the facade exceeds 30 cm, an inner guardrail comprising a top rail, an intermediate rail and a toeboard must be installed at the offset.

Compliance with recognized trade practices in scaffolding erection guarantees the safety of finishing work operatives. In accordance with LAA, the scaffolding contractor takes the technical measures required so that the temporary works provided allow safe working without risk of falls.

Managing unforeseen facade conditions and adaptations on the construction site

On a building construction site, the presence of unplanned protruding elements (monumental cornices, balcony brackets, temporary discharge pipes) forces the erector to adapt the decking during erection. Adding an extension bracket on the inner side aims to reduce the distance between the scaffolding and the finished facade line. However, this alteration changes the balance of forces and the load distribution on the vertical frames.

According to standard SN EN 12811, any change in the width of the working area impacts the platform load class. When the distance between the inner edge of the scaffolding deck and the facade surface exceeds 30 cm, fall protection is no longer ensured by proximity to the wall alone. Fitting complete inner guardrails then becomes mandatory.

  1. Identifying the gap at the facadeMeasure the gap between the main platform and the structure. If the clearance exceeds the permitted limit, determine the bracket size (0.30 m or 0.60 m) to install.
  2. Locking verificationHook the bracket onto the frame and ensure anti-uplift pins or locking wedges are fully engaged.
  3. Additional collective protectionErect the top rail, intermediate rail and toeboard on the inner side at the widened bracket if the remaining space to the wall continues to exceed safety requirements.
  4. Updating the handover noticeState the specific load restriction for the bracket area on the acceptance protocol and on the sign at the scaffolding access point.

In the event of a dispute or major alteration requested by site management, the erector refers to the erection drawing. The Construction Work Ordinance mandates clear planning of safety measures to guarantee the permanent stability of temporary works throughout all construction site phases.

Frequently asked questions

Can pallets of bricks be stored on an inner extension bracket?

No. Extension brackets are designed for pedestrian transit and temporary staging of light tools. Their permissible load is lower than that of the main bay. The load class defined by standard SN EN 12811 must be respected and heavy concentrated loads must never be placed on them.

Must a toeboard systematically be installed on the inner edge of the bracket?

Yes, whenever there is a risk of tools or materials falling below or when the clearance from the facade creates an open gap. The 15 cm toeboard prevents objects from slipping and ensures the protection of persons circulating at the base of the structure.

How should a bracket be secured if the scaffolding frame is aluminium?

Only brackets approved by the manufacturer of the aluminium scaffolding system in question must be used. Connectors and half-couplers must match the diameter of the standards without damaging the tube profile. Wedge locking must be visually verified during erection.

What should be done if the bracket creates too large a gap around a window reveal?

When the geometry of the building creates a significant residual gap despite the bracket, it is mandatory to install specific inner guardrails or bridge the gap with custom interlocking decking to eliminate the fall hazard.

Texts and standards cited

  • SN EN 12811Temporary works equipment - Performance requirements and general design for scaffolding
  • OTConstOrdinance on safety and health protection of workers in construction work

In the same section