Skip to content
Website
🧱 CFC 212Erector safety and co-activity on the construction siteChapter 2 of 10 in the section

Chinstrap helmet: why standard site helmets fail at height

At height on scaffolding, a simple loss of balance or tilting of the head is enough to send a conventional helmet falling before any impact occurs. By the end of this chapter, you will know how to apply Swiss regulatory requirements, precisely adjust a four-point chinstrap, and manage mandatory helmet replacement following an impact.

Key takeaways

  • A conventional construction site helmet falls off the head as soon as the body begins to tilt.
  • The construction work ordinance requires a chinstrap for work at height.
  • Correct adjustment of the four fastening points ensures the inner liner remains positioned during an impact.
  • Any helmet subjected to a significant impact must be scrapped and replaced immediately.

Why gravity tears off a standard helmet during a loss of balance

During the erection or dismantling of façade scaffolding, scaffolders work on narrow decking, tubes, and ledgers. In this environment, a standard construction site helmet lacking a chinstrap remains on the head solely through gravity and friction from the adjustable nape strap. In the event of a slip, trip, or backward torso tilt, angular acceleration of the head dislodges the shell. The helmet falls into the void before the scaffolder strikes a structure or impacts the ground. A helmet that comes off during free fall provides zero protection at the moment of primary impact.

Requirement to wear a protective helmet during all work where workers may be endangered by falling objects or materials; helmet worn in any case during construction work until completion of the structural work, near cranes and earthmoving equipment, during excavations, demolition, erection and dismantling of scaffolding (para. 2); helmet with chinstrap notably during work with fall protection equipment or on ropes (para. 3).

art. 6 OTConst

The Swiss rule is unambiguous: the requirement to wear a protective helmet applies on construction sites from the start of the construction site until full completion of the structural work. As soon as a worker is involved in the erection or dismantling of scaffolding or uses personal fall protection equipment (PFPE with harness and lanyard), wearing a helmet fitted with a chinstrap is mandatory. Co-activity on the construction site imposes this discipline across all trades working on or below the temporary structure.

Under art. 82 LAA, the employer must take all necessary and appropriate preventative measures permitted by the state of the art, while workers are required to cooperate by correctly using the personal protective equipment provided to them. Choosing a compliant helmet for the scaffolder is not a matter of comfort, but a fundamental safety requirement on the construction site.

Chinstrap adjustment and post-impact replacement protocol

Wearing a chinstrap helmet is not enough: the retention system must also be properly adjusted and buckled. A dangling or loose chinstrap completely negates the retention intended by the manufacturer. During an impact, a slack strap permits liner displacement, which can shift off-centre and leave the temples or forehead directly exposed to steelwork.

  1. Headband adjustmentTighten the rear headband ratchet wheel to secure the helmet to the scaffolder's head shape without creating painful pressure points.
  2. Centring lateral strapsAdjust the lateral Y-dividers so that they sit directly below the earlobes.
  3. Locking the chinstrap buckleFasten the buckle under the chin and adjust tension: the webbing must sit flush under the jaw without restricting breathing or swallowing (one to two fingers clearance tolerated).
  4. Dynamic stability testTilt the head forward and shake gently: the helmet must remain fully secure on the head, even with the buckle unfastened prior to final adjustment.
Inspection and discard criteria for scaffolder helmets
Inspected itemIdentified defectRequired action
Outer shellCracks, deep gouges, significant UV fadingImmediate disposal of the helmet
Webbing and chinstrapFraying, broken stitching, damaged buckleReplacement of chinstrap or complete helmet
Internal cradle and linerDetached anchor tabs, torn foam, depressionsReplacement of internal harness or disposal
Expiry dateExceeded lifespan specified by manufacturerSystematic replacement of the helmet

Gangers and site foremen must check helmet condition during periodic PPE inspections. A helmet stored away from ultraviolet radiation and chemicals retains its mechanical properties longer, but continuous sun exposure on façades eventually degrades shell polymers. Rigorous equipment tracking ensures effective worker protection throughout every stage of assembly.

Legal scope and co-activity on the construction site

On a building construction site, wearing head protection is not a matter of personal preference, but of a strict regulatory framework. OTConst art. 6 sets out the rule: safety helmets are mandatory for all work where there is a risk of falling objects or materials. The ordinance explicitly mandates systematic helmet use during the erection and dismantling of scaffolding, as well as during any activity carried out until the completion of the structural work. This requirement applies to all personnel present within the work perimeter, including during co-activity between trades.

When a scaffolder works at height or uses personal fall protection equipment (PFPE), standard helmets without chinstraps prove inadequate. A simple slip or sudden tilt of the head dislodges the helmet immediately, before the worker strikes a structure or a lower deck. For this reason, OTConst art. 6 explicitly requires helmets fitted with a chinstrap for operations involving fall hazards or requiring a fall arrest system.

Head protection requirements by work phase
Work situationRequired helmet typeChinstrap requirementTarget primary hazard
Erection / dismantling of scaffoldingIndustrial safety helmetMandatory fastened chinstrapFalls from height, head tilt
Co-activity under lifting operations (rigger / crane)Industrial safety helmetChinstrap recommended or requiredFalling objects, secondary impact
Work using a fall arrest systemEnhanced retention helmet (EN 12492 / EN 397)Chinstrap deemed mandatory (> 25 daN)Helmet loss during fall arrest
Enclosed finishing work (no falling object hazard)Standard construction site helmetOptional chinstrapImpacts against stationary hazards

Effective fit and discard criteria

A helmet worn with an unbuckled or poorly adjusted chinstrap is technically no better than an ordinary helmet. To ensure retention during an involuntary tilt or fall arrest, the chinstrap must be adjusted under the jaw with precise tension: the clearance beneath the webbing must not exceed the thickness of two fingers. The internal cradle must also be adjusted to the head circumference using the rear ratchet wheel to prevent any lateral slipping.

Chinstrap retention
The mechanical capacity of the webbing and buckle to hold the helmet shell securely on the head during acceleration, impact, or body inversion.
  1. Headband adjustmentTighten the rear micrometric wheel to adapt the harness to the scaffolder's head shape without pinching the scalp.
  2. Chinstrap fastening and tensioningEngage the buckle clip and adjust the length of the side straps so that the chin cup rests beneath the jaw without impeding swallowing.
  3. Stability checkTilt the head forward with the chinstrap fastened: the helmet must not slide over the brow or fall off under the dead weight of the shell.

Any helmet that has sustained a violent blow—whether from a falling object or direct impact during an off-balance fall—must be withdrawn from service immediately. Even if the outer shell shows no visible cracking, the internal energy-absorbing liner undergoes permanent deformation, rendering the PPE ineffective against subsequent impacts. The ganger regularly checks the date of manufacture stamped into the shell and orders equipment replacement in line with manufacturer specifications or at the earliest sign of UV degradation.

Emergency procedures and managing non-compliance on the construction site

During the erection or dismantling of façade scaffolding, failure to wear a correctly adjusted chinstrap helmet constitutes a serious breach of fundamental building safety rules. OTConst art. 6 requires safety helmets to be worn during construction work until completion of the structural work, and explicitly mandates helmets with chinstraps for all work involving personal fall protection equipment. If a scaffolder refuses to fasten their chinstrap or uses damaged gear, the safety officer or site foreman must stop the operation immediately. An ordinary or unfastened helmet tips off at the slightest loss of balance, leaving the worker with zero cranial protection at the precise instant of impact.

  1. Visual inspection and adjustment at the yardEvery morning, the scaffolder checks the shell condition, occipital wheel tightness, and the integrity of the four chinstrap anchor points.
  2. Immediate work stoppage upon incidentAs soon as an impact occurs or a defect is noticed in the internal cradle, the scaffolder ceases work and alerts the site manager.
  3. Replacement and discard markingThe site foreman replaces damaged helmets without delay, cuts the webbing to prevent re-use, and records the change in the team's plant register.

Collective discipline regarding chinstrap use guarantees reciprocal safety on temporary works. In accordance with the requirements of the construction work ordinance, the employer provides appropriate personal equipment and enforces continuous use until formal handover of the scaffolding. Omitting helmets or intentionally leaving chinstraps open at height exposes scaffolders to severe head trauma. If a worker persistently refuses to wear compliant head protection, the safety officer on the construction site must remove them from the work zone immediately to maintain proactive hazard prevention.

Frequently asked questions

Why is a four-point chinstrap mandatory for scaffolders?

A standard construction site helmet is designed to withstand vertical falling objects, but falls off as soon as the worker tilts their head sharply or tips backward. During façade scaffolding assembly, the helmet must remain locked to the head throughout any loss of balance or fall-arrest event. The four-point chinstrap keeps the shell firmly positioned, protecting the occiput and temples during lateral blows or violent shocks.

When should an unused chinstrap helmet stored for several years be replaced?

Even without any impact, shell polymers degrade through exposure to ultraviolet radiation, ambient heat, and natural plastic ageing. The service life of a site helmet is generally limited to three to five years from the production date stamped beneath the peak. A manual lateral compression check or noticeable discolouration requires immediate replacement, as the polymer turns brittle and loses its shock-absorbing capacity.

Does the chinstrap requirement apply to personnel remaining at the foot of the scaffolding?

OTConst art. 6 requires safety helmets for anyone present on a construction site until completion of the structural work. At the base of scaffolding being erected, the primary hazard is falling steel components, bolts, or tools. While a chinstrap helmet remains mandatory for those working at height and under suspended loads, fastening the chinstrap at ground level is strongly recommended to prevent dropping the helmet during material handling.

What should be done if a scaffolder experiences discomfort or pain from their chinstrap?

Discomfort is almost always caused by an uncentred internal harness or an overtightened strap. Adjustment must begin with the rear occipital dial to fit the head circumference, allowing the helmet to stay secure on its own without crushing the throat. The chinstrap is then tensioned so the webbing sits neatly under the ears without hindering swallowing. If discomfort continues, the employer must supply an alternative compliant model featuring padded straps or ergonomic lining.

Texts and standards cited

  • OTConst art. 6requirement to wear a protective helmet during all work where workers may be endangered by falling objects or materials; helmet worn in any case during construction work until completion of the structural work, near cranes and earthmoving equipment, during excavations, demolition, erection and dismantling of scaffolding (para. 2); helmet with chinstrap notably during work with fall protection equipment or on ropes (para. 3).

In the same section