Key takeaways
- Most basement failures stem from aggressive backfilling and not from hydrostatic pressure.
- The junction at the base of the wall requires a concave fillet and an overlap free of any incipient folds.
- The mechanical protection must resist puncturing and vertical friction during soil settlement.
- The joint inspection record signed before trench closure discharges the waterproofer and commits the earthworker.
Junction at the wall base and continuity of the barrier according to standard SIA 272
On a building construction site, water rarely penetrates a new bituminous or synthetic membrane across its main area. Failure almost systematically occurs at geometric singularities, foremost among them the junction between the basement retaining wall and the projection of the foundation slab or strip footing. Ground movements, differential settlement of the backfill, and layer-by-layer compaction apply intense shear forces precisely along this horizontal edge.
Waterproofing for underground structures must form a continuous and sealed envelope, durably protected against the mechanical, chemical and thermal stresses foreseeable during execution and service life.
norme SIA 272
- Preparation of the internal angleRemove laitance, formwork fins and honeycombing by light chiselling or grinding. Form a concave fillet (corner fillet) using shrinkage-compensated cement mortar, with a radius of 40 to 60 mm, in order to avoid sharp right-angle folding of the membrane.
- Treatment of the foundation upstand toeThoroughly clean the horizontal projection of the footing. Apply the cold bituminous primer suited to a dry or slightly damp concrete substrate, extending onto the upper face of the toe.
- Installation of the reinforcement stripTorch-weld or bond a reinforcement strip bridging the foundation slab-retaining wall construction joint across 200 mm on either side of the angle, before unrolling the main waterproofing membrane.
- Downstand and connection at the baseFully adhere the wall membrane, completely covering the fillet and the upper face of the foundation toe up to the outer concrete edge, providing a watertight connection towards the drainage bench.
Mechanical protection, work schedule and joint inspection record for closure
Waterproofing applied according to best practice remains vulnerable until it is mechanically shielded against rock impacts and vertical friction from the ground. During backfilling, the natural downward movement of material due to settlement exerts a downdrag effect that rips off mechanically fastened upstands or tears welded laps if a slip layer is not interposed.
| Type of backfill | Anticipated stress | Required mechanical protection | Installation precautions |
|---|---|---|---|
| 16/32 rounded drainage gravel | Low static pressure, moderate settlement | HDPE dimpled sheet with thermally bonded filter geotextile | Dimples facing outwards with smooth slip layer against the wall |
| 0/60 crushed excavated material | High puncturing risk, sharp edges | Rigid XPS insulation boards or fibre-cement protection sheets | Tight-joint installation wedged at the base on the toe without puncturing the membrane |
| Soft ground with water ingress | Sustained vertical friction, risk of clogging | Vertical drainage composite with cellular core and non-woven filter | 15 cm longitudinal overlap of sheets with capping flashing profile |
The execution schedule must allow for full curing or cooling of adhesives and bitumen prior to trench closure. Backfilling over waterproofing that is still warm or freshly emulsified guarantees its immediate detachment under the thrust of the first layer of gravel compacted with a vibrating plate.
If the earthworker notices a tear, accidental perforation from excavation reinforcement, or slippage of the protection during soil placement, art. 365 CO requires them to inform the client immediately via a written notification of defect, under penalty of bearing the financial consequences of subsequent water ingress. Backfilling must be halted in the affected area until the membrane is repaired using a welded patch extending at least 150 mm beyond the puncture.
Installation of waterproofing protections and backfill phasing
The tearing of a waterproofing system under the effect of soil friction or rock impact is the most frequent damage observed on buried walls. Standard SIA 272 requires a continuous physical separation between the membrane or thick bitumen coating and the imported fill materials. On the construction site, this protective barrier must withstand dynamic puncturing during tipping, as well as vertical shear forces generated by the natural settlement of successive backfill layers.
The connection at the base of the wall, at the junction between the strip footing or foundation slab toe and the elevation, is the most sensitive zone. Installing the mechanical protection must under no circumstances crush the fillet or detach the bridging strip. Perimeter insulation boards made of extruded polystyrene or dimpled sheets with integrated filter geotextile must extend down to the base of the junction fillet, without creating an overhang above the drainage channel.
| Protection system | Scope of application | Shear resistance | Site watchpoints |
|---|---|---|---|
| Thermal insulation boards (XPS) | Heated or tempered basement walls | High if continuously bonded using bituminous adhesive dabs | Avoid solvents; tight board layout without earth in the joints |
| Dimpled sheet with geotextile | Uninsulated walls with gravity drainage | Medium (slippage provided by the structure) | Filter face always oriented towards backfill; fixings above groundwater level |
| Fibre-cement or composite boards | Narrow trenches with heavy or gravelly backfill | Very high against direct puncturing | Rigorous temporary holding; no sharp edges against the waterproofing |
Joint inspection record and backfill management before trench closure
Backfilling an excavation without a formal inspection transfers full liability for subsequent water infiltration onto the masonry or earthworks contractor. The self-inspection report and the joint inspection record with site management must confirm strict adherence to drying times specified by standard SIA 272 for liquid-applied coatings, the absence of blisters or tears on the sheets, as well as the base junction before installing the drainage material.
- Visual and dimensional inspection of the waterproofed substrateVerification of system continuity, absence of air pockets under bituminous membranes, and cleanliness of the foundation slab toe. Upstands above the future finished ground level must reach the prescribed standard heights.
- Approval of mechanical protectionInspection of sheet or panel overlaps (minimum overlap according to technical data sheets, generally 10 to 20 cm for dimpled membranes), installation of top termination profiles, and integrity of the geotextile filter.
- Signing of the pre-backfill inspection recordDrawing up the joint inspection record, dated and signed by the site foreman and the site management representative, expressly authorising the start of earthworks operations.
- Layered backfilling and adapted compactionTipping without dropping rocks directly against the wall. Spreading in regular passes 30 to 50 cm thick, compacted with light plant along the structure so as not to crush the dimples or displace the protection.
Contractually, according to art. 365 CO, if any circumstance attributable to instructions received or materials specified compromises the regular or timely execution of the work, the contractor must immediately notify the client in writing. In the event of non-compliance with the waterproofing curing time imposed to meet the master schedule, a formal notification of defect discharges the execution team from consequential damage.
Regarding financial implications, the cost of complete mechanical protection (supply and installation of filter sheet or XPS boards with protective flashing) represents an indicative amount in the region of 25 to 60 CHF per square metre, depending on the complexity of steps and specified thicknesses, a ballpark figure to be checked against the unit prices series on the /soumissions/ platform.
Managing claims, damage beneath backfill, and duty to notify
A tear in a bituminous sheet or the crushing of a cellular drainage board during backfilling constitutes a concealed defect as soon as the overlying layer is compacted. If the site manager or plant operator notices an excavator bucket strike, slippage of the mechanical protection, or penetration of angular crushed aggregate through the waterproofing system, backfilling operations must stop immediately. Closing an excavation over damaged waterproofing delays discovery of the leak until the first groundwater rise or major rain event, incurring disproportionate remedial costs.
- Halting earthworks and securing the areaImmediately freeze the movement of dumpers and excavators in the affected zone. Secure excavation faces in accordance with the provisions of the Construction Works Ordinance concerning batters and earthworks.
- Manual clearing and inspectionCarefully dig out by hand or with a round shovel to expose the damaged area without worsening the tear. Summon the site management to record the extent of the damage via a photographic joint inspection record.
- Cutting back and repair according to standard SIA 272Cut out the deteriorated section of the drainage sheet. Clean the concrete substrate, apply bonding primer, and torch-weld a bituminous reinforcement patch overlapping the puncture by at least 150 mm on all sides. Then restore the continuity of the mechanical protection layer.
- Formal sign-off prior to resumptionDraft an excavation closure sign-off sheet signed by the site foreman and the civil engineer before authorising the resumption of backfilling in controlled 30 cm layers.
Should a dispute arise over subsequent ground settlement or shearing of the barrier at the base junction, the initial joint inspection record is authoritative. In accordance with CO, approval discharges the contractor for apparent defects recorded, but latent defects resulting from deliberate concealment at the time of closure remain entirely their liability.
Frequently asked questions
What should be done if the dimpled protection slips down the wall during compaction?
Stop the roller compactor immediately. Slippage indicates a failed top fixing or an excessive layer thickness dragging the sheet downwards. Manually dig out the materials over the affected height, reposition the protection board, reinforce mechanical fixings above finished ground level, and resume backfilling in reduced passes not exceeding 30 cm compacted thickness.
Can a punctured bituminous membrane be repaired without uncovering the entire wall base?
Yes, if the puncture is localised and located above the base junction zone. Excavate the backfill using a hand shovel over 50 cm around the hole. Clean the substrate, apply a bituminous primer, then torch-weld a patch with rounded corners overlapping by at least 15 cm. Then replace the mechanical protection before adding any further gravel.
Who must sign the pre-backfill inspection record if the waterproofing was installed by a subcontractor?
The joint document must bear three mandatory signatures: the waterproofing subcontractor certifying the integrity of their system, the site foreman or site manager of the masonry general contractor taking custody of the structure for earthworks, and the site management or civil engineer. This protocol formally closes installation liability and authorises the start of backfilling under the mason's supervision.
Can recycled aggregate be used as backfill material against protected waterproofing?
Only if its grading and cleanliness comply with cantonal directives and the crushed constituents do not present overly sharp edges liable to puncture the protection. Recycled gravel containing scrap metal fragments or residual glass is strictly prohibited. As a rule, a buffer layer of filtering material or rounded sand remains required along the vertical face.
Texts and standards cited
- norme SIA 272Waterproofing and drainage of underground and buried structures
- CO art. 365Defective materials and ground: contractor's immediate duty to notify
- COApproval of the work and discharge of the contractor except for concealed defects
