Key takeaways
- Stainless steel ties must systematically slope downwards towards the protective outer leaf.
- The forty-millimetre cavity requires absolute cleanliness, free from mortar snots.
- Ventilation is provided by open perpends every metre at the top and base.
- The lower flashing turns up the load-bearing masonry to shed water outwards.
Fixing stainless steel ties and inspecting the cavity
The stability of the outer leaf and the integrity of the thermal insulation rely on the rigorous installation of wall ties. Stainless steel ties of a grade suited to the outdoor environment connect the outer masonry to the inner load-bearing wall. Insufficient tie density compromises wind suction resistance, while an inverted slope turns each metal rod into a conduit guiding rainwater towards the load-bearing leaf. Adhering to installation tolerances guarantees structural performance without creating water ingress paths.
- Main area density: install a minimum of 5 ties per square metre, staggered to homogenise mechanical resistance.
- Edge and corner reinforcements: reduce spacing to 3 units per linear metre along external corners, internal corners, and opening reveals.
- Downward slope: give each tie a minimum fall of two to three millimetres downwards, directed towards the outer leaf.
- Drip feature: equip the tie with an integrated drip ring, clipped halfway across the cavity to stop capillary water movement.
The nominal thickness of the cavity must reach at least 40 millimetres to permit natural convective airflow. Rigid insulation, held flush against the load-bearing substrate by independent retaining discs, must not buckle. If the insulation swells or pulls away from the substrate due to inadequate fixing, the effective cross-section of the cavity is reduced, restricting moisture dissipation and nullifying the facade's drying capacity.
Continuous ventilation and base-of-wall waterproofing
The ventilated cavity acts as a thermal and hygrothermal exhaust duct. Rainwater that inevitably penetrates the joints of the outer leaf under wind pressure must run down unimpeded to base level, then exit outwards without ponding or rising by capillary action. This system requires continuous waterproofing detailing at the masonry base, combined with calibrated ventilation and drainage openings.
| Wall zone | Opening type | Maximum spacing | Technical function |
|---|---|---|---|
| Masonry base | Open perpend | 100 cm | Condensate drainage and air intake |
| Masonry head | Open perpend or vent grille | 100 cm | Convective air exhaust and stack effect |
| Under lintels | Protected slot | 80 cm | Intermediate exhaust on tall facades |
| Cill upstand | Open perpend | 2 per cill | Drainage below window sub-cill |
- Waterproofing membrane installationInstall a flexible bituminous or synthetic waterproofing flashing mechanically fixed to the inner load-bearing masonry, extending at least 150 millimetres above the finished external ground level.
- Base screed slopingForm a mortar fillet with a fall at the bottom of the cavity to naturally guide drainage water towards the base of the outer leaf.
- External drip overhangProject the waterproofing membrane out through the external masonry joint to create a free drip edge shedding water clear of the plinth zone.
- Weep vent installationLeave the vertical perpends of the first course open at regular intervals, incorporating calibrated rodent and insect grilles.
The site supervisor arranges the methodical inspection of the cavity base before installing each closer block. If defective elements on the internal structural work compromise the correct laying of the waterproofing membrane, the contractor alerts site management in accordance with the duty of diligence governing contract execution under the Code of Obligations (CO).
Insulation installation and stainless steel tie anchoring
In a cavity wall with masonry cladding, driving rain inevitably penetrates the outer leaf through micro-cracks in the pointing mortar. The moisture safety of the structure relies entirely on the capillary break provided by the cavity and on the strict orientation of the wall ties. An inverted slope on an anchor bracket turns each metal rod into a gutter guiding water ingress directly against the insulation board or into the internal load-bearing brickwork.
- Drip feature (drip ring)
- Plastic disc or mechanical fold located on the shank of the stainless steel tie in the centre of the cavity, designed to interrupt capillary water movement towards the load-bearing wall and shed it by gravity to the bottom of the cavity.
Anchor ties must strictly be made of austenitic stainless steel of a suitable grade (generally A2 or A4 depending on chloride exposure). Galvanised steel ties are strictly prohibited in a ventilated cavity: permanent moisture combined with alkaline mortar dust destroys the zinc layer in a matter of seasons. Inserting ties into the bed joints of the clay or calcium-silicate load-bearing wall requires a downward slope of at least 2 to 3% towards the outer leaf.
- Reinforced density: increase to 8 or 10 ties per m² along openings (window and door reveals) and at building corners across a 1 m wide band.
- Insulation fixing: each mineral wool or rigid foam board must be held tight against the inner substrate by the collared washers of the ties, with no gaps or discontinuities.
- Staggered layout: alternate the heights of tie courses to distribute wind loads uniformly without creating thermal bridging lines.
- Systematic cleaning: scrape off any squeeze-out of adhesive or fresh mortar covering the metal tie using a jointer or trowel.
Air cavity, continuous ventilation and base drainage management
A functional cavity performs two distinct roles: breaking all capillary contact between the two leaves and drying out the outer leaf via natural ascending air convection. To fulfil this role, the clear cavity width must never drop below the accepted tolerances, otherwise falling aggregates risk bridging the cavity. Visual inspection during construction is a daily duty of site supervision.
| Element | Minimum dimension | Consequence of an execution defect |
|---|---|---|
| Clear cavity (width) | 30 to 40 mm | Mortar bridging, direct wetting of the outer face of the insulation. |
| Low ventilation open perpends | 500 mm² per m² of facade | Under-ventilation, moisture stagnation at base level, and mould growth. |
| High air exhaust (under roof/lintel) | Continuous 10 mm linear opening | Thermal stack effect stops, internal condensation on the outer leaf. |
| Waterproofing flashing fall | 5% outwards | Water backflow towards the internal slab or plinth brickwork. |
At the base of the wall, water collection and drainage require meticulous detailing. The waterproofing flashing (bituminous or flexible polymer membrane) must turn up at least 150 mm on the load-bearing leaf, be mechanically fixed below the insulation, and then fall continuously towards the first course of the outer leaf. The vertical joints of the first facing course are left open (one open perpend every three or four blocks) to drain condensates and water ingress outwards, ideally protected by stainless steel rodent grilles.
- Plinth membrane installationBond or mechanically fix the waterproofing flashing to the bare load-bearing wall, above the finished external ground level, observing the minimum upstand against the inner masonry.
- Insulation board applicationInstall the first row of waterproof perimeter insulation, overlapping the upper fixing of the membrane to ensure runoff shedding.
- Drip edge and weep vent detailingPosition the membrane overhang on the base of the outer leaf, with a fold forming an external drip, then lay the first course leaving the perpends free of mortar.
- Inspection prior to closureManually clear mortar snots that dropped to the bottom of the cavity during the initial courses using a scraper or through temporary cleanout openings at the base of the wall.
Managing non-conformities and remediating moisture defects
In a cavity wall, water penetration towards the inner leaf stems almost exclusively from three execution errors: ties installed sloping inwards guiding condensation water, a cavity clogged by mortar snots forming a capillary bridge, or a wall base lacking a drip edge and functional weep vents.
- Detection and elevation haltAs soon as a drainage defect or mortar bridge is detected, the chargehand halts the outer leaf construction to open up the affected joints before the mortar cures fully.
- Formal notification to site managementThe contractor exercises their duty to notify under art. 365 CO para. 3 by immediately confirming in writing any detail defect or obstruction compromising cavity drainage.
- Mechanical remediation and cavity clearingLocally remove bricks at the base of the wall, scrape mortar deposits off the waterproofing membrane using a narrow trowel, and reset the tie drip washers.
- Re-establishing ventilation areasInstall clean rodent grilles in the open perpends at the base and head, ensuring the required clear ventilation area across the entire facade run.
If an expert report reveals a widespread lack of drainage after completion, the client's rights are exercised under the Code of Obligations (CO) and standard SIA 118. Rectification requires opening targeted areas at the base of the facade to clear the waterproofing membrane, correct the angle of the stainless steel ties, and rebuild the weep outlets. Local remediation of these non-conformities typically costs between 4,000 and 12,000 CHF per facade, depending on the required scaffolding height.
Frequently asked questions
How do you correct a stainless steel tie installed sloping down towards the insulation?
If the mortar in the load-bearing wall has already set, never bend the rod forcefully, as this risks cracking the brick or pulling out the anchor plug. Adjust the plastic retaining disc to recreate a low drip point directed towards the outer leaf, or crop the defective tie flush and install a new compliant stainless steel tie slightly sloping outwards.
How do you prevent mortar accumulation at the base of the cavity during construction?
Bricklayers suspend a timber cavity batten on ropes at the bottom of the cavity, above the waterproofing membrane. With each course of bricks laid, the batten is raised one step to catch and clear fresh snots dropping behind the insulation. This prevents the lower weep vents from becoming permanently clogged before the masonry is closed up.
What is the minimum cross-section for ventilation openings at the base and head of the wall?
According to recognised technical rules, continuous ventilation requires a minimum of 500 mm² of free opening per linear metre of facade. In construction site practice, bricklayers leave an open perpend without mortar every two or three bricks, both at the base and under the parapet coping flashing, systematically fitted with a calibrated rodent comb or grille.
What should be done if the wall base waterproofing membrane is punctured during drilling?
Any puncture in the waterproofing membrane compromises the drip detail and allows water to run into the slab. Clear the contaminated area, degrease the repair surface, and apply a bituminous or EPDM waterproofing patch cold-bonded with a minimum overlap of ten centimetres. A rigorous visual inspection is mandatory before closing up the facing masonry.
Texts and standards cited
- norme SIA 118General conditions for construction works
- CO art. art. 365 COMaterials and ground: the contractor immediately reports any circumstance compromising the works
