Skip to content
Website
🧱 CFC 201 / 211.0Mortars, site-mixed concretes and placement productsChapter 1 of 10 in the section

Concrete to SN EN 206: select exposure class for the structure

On Swiss construction sites, ordering ready-mixed concrete tolerates no guesswork. This chapter teaches you how to decipher a complete mix design to standard SN EN 206, select exposure classes suited to the structure's environment, and avoid contractual pitfalls linked to technical deviations upon delivery.

Key takeaways

  • A complete designation specifies strength, exposure classes, consistency, and Dmax.
  • The choice of exposure classes directly dictates durability and mix design.
  • The consistency ordered must suit the formwork without ever adding water on the construction site.
  • Any deviation from the specifications immediately incurs the contractor's contractual liability.

Deciphering the complete designation according to standard SN EN 206

In the field, the standardised designation of ready-mixed concrete constitutes the direct technical link between the civil engineer's drawings and the batching plant. A specified mix design is not just a matter of compressive strength; it defines a set of fresh and hardened properties essential to the durability of the structure. Reading this string of characters correctly avoids truck mixer rejections and ensures placement in accordance with recognised trade practices.

Complete concrete designation
Standardised sequence according to standard SN EN 206 grouping compressive strength class, environmental exposure classes, maximum aggregate size (Dmax), consistency class, and, where applicable, chloride content or special requirements.
Key parameters of a standardised concrete mix design
ParameterCode examplePractical meaning for the construction site
StrengthC25/30 or C30/37Characteristic compressive strength on cylinder and cube at 28 days.
ExposureXC4, XF1, XD1Environmental actions sustained by the element in service.
AggregatesDmax 32 (or 16)Maximum aggregate size suited to reinforcement and thickness.
ConsistencyF3, F4, or C3Workability at delivery measured by flow table or degree of compactability.
ChloridesCl 0.20Maximum chloride ion content by mass of cement.

The choice of maximum aggregate size (Dmax) directly influences internal compaction. A Dmax of 32 mm is perfectly suited to massive strip footings and standard foundation slabs, whereas a Dmax of 16 mm is required for thin, heavily reinforced walls or complex geometries to prevent honeycombing. Similarly, the consistency class (generally measured by flow table from F1 to F6 according to the flow table test method) determines fluidity: F4 concrete flows easily from the skip or pump line, whereas F2 concrete requires vigorous and continuous vibration.

Selecting the exposure class and avoiding contractual deviations

Exposure classes define the chemical and physical actions that concrete will experience during its service life. Under standard SN EN 206, a single structure often combines several classes. An unsheltered external retaining wall will typically be classified as XC4 (carbonation-induced corrosion with cyclic wet and dry conditions) and XF1 (moderate freeze-thaw attack without de-icing agents). If this same wall borders a cantonal road subject to winter brine spray, it must switch to XD3 and XF4, requiring an air-entraining agent and sulfate-resistant cement.

Common mapping of exposure classes in building construction
Main classType of actionTypical structure example in Switzerland
X0No risk of corrosion or attackInternal unreinforced concrete, blinding concrete.
XC1 to XC4Concrete carbonationXC1/XC2 for dry internal slabs; XC4 for external facades.
XD1 to XD3Chlorides other than from sea water (de-icing salts)XD3 for underground car park slabs, access ramps, and road edges.
XF1 to XF4Freeze-thaw attackXF1 for exposed facades; XF4 for kerbs and saltwater gullies.
XA1 to XA3Chemical attack from soil/groundwaterBuried structures in contact with aggressive groundwater.

The frequent trap lies in unagreed cost optimisation. Ordering C25/30 XC2 concrete instead of the specified C30/37 XC4 saves a few francs per cubic metre on purchase, but constitutes a major departure from the specifications. A contractor who places an under-dosed or unsuitable mix design commits a direct breach of contract. Under art. 365 CO, the contractor is liable for the quality of the material supplied. If the batching plant delivers a non-compliant mix or if the site foreman signs off on a downgraded delivery note, the company bears all remediation, expert assessment, or reconstruction costs set out in art. 368 CO.

  1. Order verificationCompare point by point the concrete schedule in the works contract (strength, XC/XF/XD, Dmax, consistency) with the batching plant's approved quote.
  2. Inspection upon truck mixer arrivalRequire the delivery note immediately before any unloading. Check the strength class, stated exposures, batching time, and specified consistency.
  3. Managing non-conformitiesIf the delivery note indicates a downgraded concrete (e.g. XC2 instead of XC4), reject the skip immediately, record the exact reason on the delivery note, and notify the site management.

Order specifications: consistency, aggregate, and placement method

On the construction site, ordering from the batching plant is not limited to compressive strength class or environmental exposure. The site foreman and the site manager must lock down three decisive physical parameters: maximum aggregate size ($D_{max}$), consistency class, and delivery method. An error in these criteria compromises element compaction, increases the risk of segregation, or blocks the concrete pump.

Selection criteria for ordering fresh concrete based on formwork conditions
Structural elementUsual consistencyRecommended $D_{max}$Placement method
Thick foundation slab with light reinforcementC3 (very plastic) to F432 mmDirect discharge via chute or skip
Standard wall thickness 20 to 25 cmF4 (very fluid) or F516 mm to 22 mmConcrete pump or skip with tremie pipe
Heavily reinforced column or nodeF5 (fluid) or SCC (self-compacting concrete)8 mm to 16 mmPumping from the bottom or skip with hose sleeve
Topping slab on prestressed unitsF416 mmStationary concrete pump or truck-mounted pump

The choice of aggregate directly affects pumping behaviour. Crushed quarry aggregate requires more cement paste and admixtures than rounded alluvial aggregate to achieve the same workability. For long-distance pumping or substantial heights in Romandie, always clarify the nature of sands and gravels with the plant dispatcher to avoid line blockages.

Construction site receipt, delivery note, and non-conformity management

  1. 1. Immediate check of the delivery noteVerify exact correspondence between the written order and the paper or digital delivery note prior to discharge: complete standardised designation, exposure class, strength class, consistency, batching time, and volume.
  2. 2. Visual inspection and consistency measurementObserve mix homogeneity at the start of discharge. In case of doubt regarding workability, perform a slump test (Abrams cone) or flow table test before authorising discharge into the skip or pump hopper.
  3. 3. Sampling for test specimensCast the test cubes or cylinders required by the site quality control plan, and store moulds protected from drying out and thermal shock according to testing standards.
  4. 4. Managing rejection and traceabilityIf the concrete received deviates from the specifications (e.g. internal non-frost-resistant concrete delivered for an external wall), reject the truck mixer, record the exact reason on the delivery note with the driver's signature, and notify the site management.

Any deviation between the order and the engineer's specifications falls squarely under the masonry contractor's responsibility. Under art. 365 CO, the contractor is liable for the quality of materials supplied for the work. Accepting a downgraded concrete to achieve marginal purchase savings exposes the company to complete element replacement if defects appear (freeze-thaw scaling, early carbonation, reinforcement corrosion). Furthermore, CO requires the contractor to carry out the work with due care; placing a mix non-compliant with tender drawings triggers civil liability in the event of failure or damage.

Crisis management: mix design non-conformity and order disputes

On the construction site, discovering a deviation from the specifications often happens too late—when the truck mixer is already discharging or during post-pour delivery note audits. Substituting a specified mix with an ordinary variant to cut costs is a severe technical fault. Standard SN EN 206 links exposure class directly to the structure's real durability: concrete batched without an air-entraining agent under de-icing salt exposure, or with an excessive water/cement ratio under carbonation risk, will cause premature reinforcement deterioration.

  1. Immediate rejection upon deliveryIf the delivery note indicates an exposure class, maximum aggregate size Dmax, or consistency class not conforming to the complete designation of the concrete ordered, reject the truck mixer before any discharge begins. Record the exact reason on the note and have the driver sign.
  2. Immediate notice to site managementPursuant to art. 365 CO, the contractor immediately reports any defective material or incident jeopardising the work to the client or their representative. In the event of inadvertent pouring of a non-compliant mix, record the precise location on concreting drawings and demand grading curves and batch records from the plant.
  3. Precautionary sampling and core drillingHave additional specimens taken on site by an accredited laboratory to test strength and porosity. If the concrete has already hardened without prior testing, schedule core drilling to verify in-situ density and actual strength in accordance with the civil engineer's instructions.

In the event of a structural failure attributable to blatant disregard for strength or mix specifications, the site manager or site foreman may face criminal liability under CP if recognised rules of the building trade were knowingly breached, endangering life or limb.

Frequently asked questions

What should be done if the delivered consistency is stiffer than stated on the note?

Adding water to the mixer drum on the construction site is strictly forbidden, as this practice destroys the water/cement ratio and the exposure class under standard SN EN 206. The chargehand must reject the delivery or request the addition of a compatible plasticiser under the sole responsibility of the batching plant, recording the adjustment and mixing time on the delivery note.

How should one respond if the delivered Dmax bridges in the reinforcement?

Stop concreting immediately to prevent honeycombing and voids around the reinforcement. The complete concrete designation must strictly comply with clear rebar spacing. If the delivered aggregate is oversized (for example 32 mm instead of 16 mm), the truck mixer must be sent back to the plant. The engineer must approve any remediation method for the area already poured.

Who bears the additional cost if the engineer imposes a higher exposure class during construction?

If the change results from evolving requirements from the client compared to the initial quote, this constitutes an order variation entitling the contractor to an additional charge under standard SIA 118. The contractor must give written notice of the price difference before ordering concrete from the plant, detailing the financial impact on the affected measured quantities.

Can XC1 concrete be poured for a sheltered external wall?

No, this is a serious non-conformity. Even when protected from direct rain, an external element undergoes ambient air humidity fluctuations and requires at least class XC4 under standard SN EN 206. Class XC1 is reserved for concrete inside dry buildings without condensation. Using class XC1 externally accelerates carbonation and causes premature deterioration of reinforcing steel.

Texts and standards cited

  • SN EN 206Concrete: specification, performance, production, and conformity
  • norme SIA 118General conditions for construction works
  • CO art. 365Material and ground: the contractor is liable for the quality of materials supplied; if any circumstance compromises proper execution of the work, the contractor must immediately inform the client, under penalty of bearing the consequences (para. 3)
  • CPBreach of the recognised rules of building: penalises anyone who knowingly or through negligence breaches recognised building rules, endangering life or physical integrity

In the same section