Skip to content
Website
🧱 CFC 250Appliances, connections and built-in fittingsChapter 8 of 10 in the section

Accessible sanitary facility: heights, turning space, grab bars and taps

This chapter details the openings and setting-out dimensions essential for delivering a sanitary unit that complies with requirements for people with reduced mobility. You will learn how to lock in the centre distance of the support frames, the exact height of seats and controls, the anchoring of wall reinforcements and the clear turning space on the finished floor before the lightweight partitions are closed.

Key takeaways

  • The position of the wall-hung WC pan is set at 46 centimetres above the finished floor level.
  • The 140 centimetre turning space requires rigorous coordination of thicknesses with the tiler.
  • The multiplex timber fixing cross-members are inserted into the metal framework before any wall cladding.
  • Operable taps require a cartridge with no resistance and a control within easy reach.

Fix the frame heights and wall reinforcements before the lining

In a bathroom for a person with reduced mobility, a setting-out error is unforgiving. Once the plasterboard is screwed on and the tiles are glued, readjusting a water outlet or raising a support frame becomes technically or financially disproportionate. The sanitary installer must coordinate with the quantity surveyor and the screed layer to mark the one-metre finished level line. A variation in the thickness of screed or tile adhesive changes the usable height of the ceramic fixture by the same amount.

For the wall-hung WC pan, the standard support frame is not always suitable for the loads of a person leaning with their full weight on the front edge. Reinforced self-supporting brackets should be selected, plugged into the raw concrete slab before the levelling screed is poured. The threaded rods carrying the ceramic are adjusted by calculating the floor finishing build-up precisely. To obtain a finished pan at 46 cm, the axis of the porcelain fixing studs is generally set at around 38 to 40 cm from the raw floor, depending on the specified seat model.

Setting-out heights for accessible sanitary facilities according to SIA 500
Sanitary elementRecommended finished heightExecution toleranceReference point
WC pan seat46 to 48 cm+/- 5 mmTop of the closed seat
Washbasin without pedestal75 to 80 cm+/- 10 mmTop edge of the basin
Clear space under washbasin67 cm minimum0 mm set backKnee clearance in a wheelchair
Flush control axis85 to 100 cm+/- 20 mmPlate or remote flush button
Washbasin mixer tap80 to 90 cm+/- 10 mmOperating lever at rest

The anchoring of fold-down or wall-mounted grab bars requires a minimum mechanical pull-out resistance that simple plasterboard cladding cannot provide. These bars must withstand a static vertical load of 100 kg applied at their end without the partition deflecting. The sanitary installer must integrate into the thickness of the 75 or 100 mm metal profiles cross-members made of birch multiplex board at least 30 mm thick, or dedicated galvanised steel plates, fixed to the framework studs. Once the board is fitted, marking the exact location of this reinforcement avoids drilling into a void when fitting the accessories.

Ensuring free turning space, washbasin clearance and operability

The clear turning space is the second major constraint, dictated as soon as the partitions are set out on the raw slab. The SIA 500 standard prescribes a circle with a minimum diameter of 140 cm, free of any fixed obstacle, allowing a standard-sized wheelchair to make a complete turn. This manoeuvring space must lie outside the swing of the bathroom door, unless the door opens outwards or slides on the surface.

The accessible washbasin requires a particular technical approach to the trap and the waste. A traditional bottle trap hanging under the basin prevents a frontal approach by injuring the thighs or hitting the wheelchair footrests. Fitting a concealed trap under a watertight box or a tubular trap offset against the rear wall ensures a clear space under the basin at least 67 cm high and 30 cm deep. The PE waste pipe axis, with a diameter of 50 mm, must be positioned precisely in the framework so as not to interfere with fixing the support bar or the supply pipes.

Mixed water and its control must be usable without twisting the wrist. Taps with notched rotary knobs are prohibited in favour of single-lever mechanical mixers fitted with an extended lever of at least 12 to 15 cm, or infrared sensor systems. The resistance to opening must not require excessive force. In the accessible level-entry shower area, the tap is installed at a height between 85 and 100 cm above the finished floor, positioned so that a person seated on a fold-up seat can reach the handle without contortion. To avoid scalding in the event of accidental pressure on the lever, fitting a thermostatic system with a safety stop at 38 degrees Celsius remains the technical rule accepted by the trade.

On the construction site, if the execution drawings provided by the site management contain dimensions that reduce the clear turning space below the usable threshold or omit the thickness of the finishes, art. 365 CO para. 3 requires the installer to warn the principal without delay. This written notice relieves the sanitary installer of liability before the screeds cover the floor pipework.

Support frames and load-bearing reinforcements: setting the WC pan and the bars

In a bathroom accessible to people with reduced mobility, the sanitary installer bears direct responsibility for the usage dimensions well before the plasterer and the tiler come in. Once the moisture-resistant plasterboard is fitted and the tiles are glued, correcting a wrong seat height or moving the axis of a concealed tap requires the complete demolition of the partition. Mounting the frames on the surface or in a service duct therefore requires an absolute check of the official level line of the floor. The cumulative thicknesses of the floating screed, any decoupling mat and the porcelain stoneware must be deducted to the millimetre to adjust the telescopic feet of the frame.

The SIA 500 standard sets the top height of the wall-hung pan seat between 46 and 48 cm above the finished tiling. A standard factory-supplied support frame is pre-set for a common height of 40 to 42 cm. If the fitter does not compensate for this 6 cm difference on the threaded rods when tightening the feet to the raw floor, the pan will be too low to allow side transfer from a wheelchair. In addition, the spacing of the fold-down or fixed grab bars requires the prior incorporation of reinforcing cross-members in galvanised steel or multiplex plywood panels at least 30 mm thick firmly anchored to the metal studs. Toggle anchors or hollow-wall plugs in a simple plasterboard sheet never withstand repeated pull-out stresses.

The four accessibility dimensions fixed before lining the walls
Sanitary elementDimension on raw floor (70 mm screed reference)Finished usage dimensionDirect impact in case of setting error
WC pan threaded rods390 to 410 mm from the raw floor460 to 480 mm on the seatWheelchair transfer impossible if too low; feet dangling if too high
Cross-members for grab bars770 to 820 mm from the raw floor700 to 750 mm bar axisImmediate pull-out from the partition in the absence of a recessed load-bearing block
Axis of the WC frame relative to the side wall450 mm raw axis, finished450 mm net at the tilingInsufficient space to bring the wheelchair alongside the WC pan
Concealed washbasin waste socket520 to 550 mm from the raw floorClear space under the basinKnees blocked during frontal approach under the vanity top

Operable taps and wall controls: alignments and clearances

The clear turning space with a minimum diameter of 140 cm, required by the SIA 500 standard for buildings with adaptable housing, determines the location of every sanitary projection. No exposed connection may encroach on this manoeuvring volume at floor level. For the washbasin, a trap recessed in the masonry or concealed behind the dry partition, connected to a specific flat pipe, is imperative. Any exposed vertical waste under the basin prevents the legs of a person seated in a wheelchair from fitting under it and exposes the user to the risk of burns from contact with the hot water drain pipe.

Operable taps require handles designed to be actuated without a strong palm grip. The installer favours mixers fitted with an extended ergonomic control lever or contactless electronic activation by infrared sensor. In the level-entry walk-in shower, the thermostatic mixer must be positioned between 85 and 100 cm above the finished floor, offset from the axis of the fold-down seat so that it remains accessible both from outside the shower tray and by the seated occupant. A pre-set mechanical-stop anti-scald safety system protects users with impaired bodily sensation.

  1. Take the level references of the floorLocate the one-metre level line transferred by laser by the project manager. Calculate the actual floor build-up (screed and tiling) before starting to mount the frames for wall-hung pans and sinks.
  2. Position and fix the stiffening cross-membersBolt the fixing plates for the grab bars to the partition studs. Check the horizontal alignment of the reinforcements at a finished height between 70 and 75 cm above the tiled floor.
  3. Seal the openings for the concealed tapsFit the installation bodies of the thermostatic shower mixer and the remote WC flush control. Adjust the plastic protection sleeve to the expected thickness of the wall tiling.
  4. Measure the lateral turning clearancesCheck with a tape measure that there is a lateral clearance of at least 90 cm on one side of the WC to allow the wheelchair to pull up alongside, before signing the setting-out record.

Managing dimensional deviations and corrections before closing the walls

On an accessible bathroom construction site, a setting-out error is unforgiving once the tiling is laid. The four critical dimensions — seat height of the wall-hung WC, clearance under the basin, spacing of the wall reinforcements for grab bars and the 140 cm net turning circle — are all locked in on the raw metal framework. If the level line of the structural work drifts, or if the final thickness of the screed and tile build-up is changed along the way, a support frame fixed too low will make the pan non-compliant as soon as the fixtures are commissioned.

As soon as a dimensional deviation is found during the dry check of the load-bearing structure, the sanitary installer must stop the plasterboard lining. A written joint inspection record must be drawn up with the site management and the plasterer-painter, recording the actual finished floor dimension validated at the laser level. Correcting the threaded rod of a Geberit frame or adjusting the multiplex timber anchoring cross-member takes twenty minutes before boarding; demolishing sealed tiling afterwards to move an angled bar or to raise a concealed waste elbow incurs disproportionate costs and destroys the work of the adjacent trades.

Deviations in functional dimensions and corrective measures before lining
Check pointExecution toleranceConsequence after tilingCorrective measure on raw framework
WC pan seat height (46 to 48 cm finished floor)+/- 5 mmWheelchair transfer impossible, non-complianceLoosen the telescopic feet of the frame and adjust with a laser
Clearance under washbasin (70 cm knee clearance)+10 / -0 mmFootrests hitting or trap blocking accessRaise the fixing studs and move the concealed trap back
Reinforcements for wall grab bars+/- 10 mmAnchoring screws in a void behind the tilingInsert a multiplex board backing fixed to the partition profiles
Clear turning area (140 cm net diameter)-0 mmWheelchair blocked by the fixtureMove the frame sideways before final fixing

When the error is discovered late on finished tiling with no internal reinforcement present, the installer must under no circumstances mount a grab bar with simple expansion plugs for hollow walls in the plaster. The pull-out load required to support a person then requires the targeted removal of the tiles and the careful opening of the partition to incorporate the required cross-members, otherwise the installation will fail.

Frequently asked questions

How do you adjust the height of the accessible WC pan if the finished screed level changes by 3 cm?

If the partition is not yet lined, loosen the locking screws of the telescopic feet of the self-supporting support frame to correct the axial height of the threaded rods according to the new official level line. If the tiling is already laid, the frame can no longer be modified; the only remaining technical option is to fit a specific raised pan of suitable shape, provided the waste axis remains within the tolerance of the connector.

Why should conventional exposed traps under a wheelchair-accessible basin be prohibited?

A conventional straight or bottle trap under the basin strikes the knees and footrests of a wheelchair user, while also risking contact burns from very hot waste water. The Swiss standard requires a specific flat trap to be recessed into the service partition or a pipe offset towards the rear to completely clear a free space 70 cm high under the underside.

What solution should be adopted if no grab bar reinforcement was inserted in the dry partition?

If the lining is complete and tiled without internal reinforcement in multiplex timber or steel, fitting wall grab bars on plasterboard plugs is ruled out because the fixing would give way at the first heavy pull. The only reliable solution is to remove the tiling locally, open the board to insert a rigid reinforcement anchored to the metal studs, or switch to bars fixed on vertical posts anchored directly in the raw slab.

What criteria govern the choice of taps for a contactless accessible sanitary facility?

The mixer must be operable without pronounced muscular effort, either by means of an extended medical lever that is easy to operate with the wrist or elbow, or via a contactless optoelectronic detection cell. The equipment must imperatively include a thermal safety stop or a factory-set thermostatic cartridge to eliminate any risk of scalding if the user cannot quickly withdraw their hands from the flow.

Texts and standards cited

  • norme SIA 500Barrier-free construction: dimensional requirements, mounting heights, turning areas and accessible sanitary equipment
  • norme SIA 118General conditions for the execution of construction work: execution rules, tolerances and joint inspection records

In the same section