Skip to content
Website
🧱 CFC 250Drinking water: introduction, protection and meterChapter 7 of 10 in the section

The outdoor tap: draining, frost protection and backflow protection

By the end of this chapter, you will be able to size and connect an outdoor draw-off point that complies with the SSIGE guidelines. You will master the selection of devices protecting against the return of polluted water by back-siphonage or back-pressure, as well as the rules for installing a self-draining, through-wall frost-proof tap with a downward slope towards the outside.

Key takeaways

  • A submerged garden hose creates a direct risk of biological or chemical contamination of the drinking water network.
  • The SSIGE guidelines require a suitable protective device against backflow on every outdoor draw-off point.
  • The frost-proof tap places its shut-off mechanism in the heated zone to prevent the body from bursting in freezing conditions.
  • The façade penetration requires a minimum slope towards the outside to ensure complete gravity drainage.

Backflow protection: securing the public network against outdoor uses

The outdoor draw-off point is one of the most vulnerable links in an indoor sanitary installation. As soon as a garden hose is connected to the tap nozzle, its open end may end up submerged in a rainwater collection tank, a garden treatment tank, a bucket of detergent or an inflatable pool. If a main pipe breaks on the public network or if pressure suddenly drops in the riser, a vacuum is created instantly in the supply pipe. Without a certified mechanical barrier, the siphon effect draws the polluted liquid directly into the building's drinking water system and then into the municipal distribution pipe.

To neutralise the risk of back-siphonage or back-pressure on ordinary watering points, the installer uses two main technical principles. The first is to fit an end-of-line disconnector or a safety combination unit for garden taps, combining a non-return valve and a pipe vacuum breaker. As soon as the upstream pressure drops below atmospheric pressure, the vacuum breaker admits free air, cutting the liquid column cleanly and eliminating any suction effect. For fixed high-risk or automated installations, such as buried irrigation systems with fertiliser dosing, fitting a controllable reduced-pressure-zone backflow preventer, either the non-verifiable type CA or the verifiable type BA, becomes mandatory upstream of the branch.

Backflow protection devices for outdoor draw-off points
Use configurationFluid category (SSIGE guidelines)Mandatory protection deviceMechanical operation
Simple garden tap with removable flexible hoseCategory 3 fluidCombined non-return valve and end-of-line vacuum breaker (type HA or HD)Mechanical closing of the valve and immediate air admission when pressure is cut
Buried irrigation network without added productsCategory 3 fluidNon-verifiable reduced-pressure-zone backflow preventer (type CA)Discharge to atmosphere physically separating the drinking water network from downstream
Irrigation system with fertilisation or additive suctionCategory 4 fluidVerifiable reduced-pressure-zone backflow preventer (type BA)Maintaining an intermediate chamber open to the air, with periodic inspection

The self-draining frost-proof tap: through-wall installation and drainage slope

Using an internal stop valve with a manual drain cock has recurring operational weaknesses: the occupant often forgets to close the valve and open the drain before the first autumn frosts, causing the pipe to burst through the expansion of ice in the wall. The self-draining façade tap solves this human failure. Its principle relies on a through-wall body whose sealing seat and shut-off valve are located not outside, but at the inner end of the tube, deep within the heated or temperate volume of the building. A long axial operating rod connects the external control handwheel to this internal valve.

Self-draining frost-proof tap
Through-wall façade tap whose shut-off seat remains located in the frost-free zone. As soon as the handwheel is closed, the residual water in the wall penetration is pushed outwards by depressurisation, completely emptying the pipe exposed to the cold.
  1. Core drilling and fitting the sleeveDrill through the external wall with a core drill of the diameter suited to the through-wall bush. Fit a watertight protective sleeve to isolate the copper or stainless steel tube from the masonry and the grout.
  2. Setting the slope towards the outsidePosition the through-wall body with a continuous downward slope of 1 to 2% towards the outer nozzle. This gradient ensures that the volume of water downstream of the seat drains spontaneously by gravity each time the tap is shut off.
  3. Internal connection and wall fixingConnect the pipe to the cold water distribution, fitting a dedicated isolation valve. Fix the external wall plate to the render or dressed stone with a weather-resistant seating gasket.
  4. Checking drainage on disconnectionCheck the automatic drain by closing the tap: water should drip briefly from the tap nozzle. Remind the client that quick-release couplings with aquastop must be disconnected in winter to allow air to enter.

The two shut-off and safeguard devices: applying the SSIGE guidelines

An outdoor watering connection is one of the most vulnerable points of an indoor sanitary distribution network. As soon as a flexible hose remains connected to the draw-off tap, its free end frequently dips into a retention basin, a rainwater tank, a pesticide mixing tub or a muddy area. If a sudden pressure drop occurs on the public drinking water network during a main pipe break or a high fire-fighting demand on a nearby hydrant, an immediate vacuum is created in the riser. The hose then acts as a perfect siphon: the soiled liquid outside is drawn in a few seconds into the heart of the building's distribution pipes, contaminating the drinking water intended for human consumption.

To eliminate this danger of back-siphonage and backflow, the SSIGE guidelines for drinking water installations require two inseparable devices on every outdoor draw-off point without a visible air gap. The first is an anti-pollution non-return valve, placed upstream of the draw-off point. This mechanical valve prevents any fluid from flowing back as soon as the downstream pressure exceeds the upstream pressure. The second mandatory device is a pipe vacuum breaker or atmospheric vent. If pressure drops in the supply pipe, this air-admission valve opens under atmospheric pressure, immediately cutting the water column and breaking the siphon effect before the water in the hose can flow back.

Classification of contamination risks at an outdoor water point according to the SSIGE guidelines
Typical outdoor useFluid category (standard)Identified health riskMandatory device
Simple lawn watering with a hanging hoseCategory 2 fluidChange in taste or temperature without toxicitySimple verifiable check valve
Garden hose lying on the ground or submerged in a containerCategory 3 fluidPresence of bacteria, slightly harmful substancesHydraulic backflow preventer with integrated vacuum breaker
Fixed irrigation system with liquid fertiliser injectionCategory 4 fluidProven toxicity, dangerous chemical moleculesReduced-pressure-zone backflow preventer, non-verifiable or verifiable
Direct filling of a garden pond without a break tankCategory 5 fluidSerious pathogens, microbiological agentsBooster set with break tank and total overflow of type AA or AB

Through-wall installation of the self-draining tap and setting the slope

To reconcile health protection against backflow with protection against winter frost, without imposing a tedious manual draining on the owner, the rule of good practice is to install a self-draining façade tap. This one-piece component relocates the hydraulic shut-off mechanism: the operating handle is on the rendered external façade, but the actual stop valve is at the end of a through-wall rod, beyond the perimeter insulation, in the heated volume of the cellar or technical room. As soon as the external handle is closed, the internal valve cuts off the pressurised water supply, while an internal channel releases the standing water contained in the through-wall tube body, which drips out to the outside.

  1. Core drilling the wall and fitting the sleeveDrill through the concrete or masonry external wall with a diamond core drill, applying a continuous slope of 2% towards the outside from the start of drilling. Fit an airtight and watertight protective sleeve to isolate the copper or stainless steel tube from the masonry and the façade insulation.
  2. Adjusting the length and sealingCut the tap body and the central operating rod to the total thickness of the finished wall, including render and external thermal insulation. Fix the façade plate with suitable plugs, then carefully seal the base with an elastomeric sealant resistant to ultraviolet rays to prevent any rain infiltration behind the render.
  3. Internal connection and flow checkConnect the upstream pipe to the drinking water distribution with a dedicated stop valve fitted with a service drain plug. Carry out repeated opening and closing tests to confirm that the barrel decompresses without resistance and that the vacuum breaker immediately breaks the vacuum.

Outdoor point pathologies: diagnosing frost damage, reverse slope and non-compliant disconnection

The most common malfunction found during winter frosts concerns so-called frost-proof taps that were compliant when leaving the workshop. In nine cases out of ten, the damage comes from leaving a quick-release hose coupling with a closed spray lance on the tap nozzle. This accessory blocks the mechanical venting: the water cannot drain by gravity out of the through-wall tube. The trapped water freezes within the thickness of the façade, expands the copper or brass shaft and causes the tube to rupture or the internal valve to come loose during the spring thaw, causing flooding in the inner partition or the cellar.

In the event of bursting or a permanent leak at the gland, the repair procedure requires closing the dedicated isolation valve located in the heated room, depressurising the pipe and removing the axial operating rod from the façade. If the internal seat is deformed by ice, complete replacement of the through-wall cartridge is unavoidable. The core-drilled opening in the wall must then be probed. If the opening has a reverse slope towards the habitable rooms, the drain water stagnates at the bottom of the housing. The sanitary installer must elongate the opening with a hammer drill to restore a downward slope of 1 to 2% towards the outside before injecting new closed-cell polyurethane foam and sealing the mounting plate.

If the watering network is supplied by a conventional tap without a certified backflow preventer, any accidental siphoning caused by a pressure drop on the public network makes stagnant or fertiliser-laden water flow back from the garden hose into the drinking water distribution. On finding this, the installation must be taken out of service immediately, drained, flushed in reverse flow, then fitted with a combined device compliant with the SSIGE guidelines, combining a non-return valve and a pipe vacuum breaker.

Frequently asked questions

Why does a frost-proof garden tap burst despite its self-draining feature?

The main cause is the permanent connection of a garden hose fitted with a closed spray gun. The mechanical vacuum breaker of the device cannot draw in the air needed to break the water column. The water remains trapped inside the wall penetration. At the first prolonged frost, the trapped water freezes, expands and splits the metal tube within the thickness of the building's insulation.

How do you correct a frost-proof tap installed with a reverse slope towards the inside?

The reverse slope prevents gravity drainage towards the outside when the mechanism is closed. Disconnect the internal connection in the heated zone, remove the external wall plate, enlarge the through hole to tilt the housing towards the garden with a minimum slope of 1%, then wedge the whole assembly rigidly before redoing the perimeter air and rain seal.

What backflow protection does the SSIGE require on a watering point?

According to the SSIGE guidelines for drinking water installations, outdoor watering presents a risk of immersion in water soiled by fertilisers or bacteria. The distribution must be secured by a hydraulic backflow preventer or at least by an assembly combining a non-return valve and an automatic vent breather, preventing any vacuum from drawing the contents of the hose into the drinking water network.

How do you winterise a traditional outdoor installation without an automatic frost-proof system?

On a conventional installation, the installer must close the internal stop valve located in the frost-free zone, open the small drain cock on the body of this valve to empty the façade pipe into a bucket, then open the outdoor tap fully and leave it open all winter to allow the residual moisture to expand freely.

Texts and standards cited

  • Directives SSIGE W3Guidelines for drinking water installations, general principles of distribution and protection of water quality
  • Directives SSIGE W3/E1Protection against backflow in indoor drinking water installations

In the same section