Skip to content
Website
🧱 CFC 250Appliances, connections and built-in fittingsChapter 2 of 10 in the section

The flush-mounted outlet: position, projection, protection and preparation for waterproofing

By the end of this chapter, you will be able to determine exactly the projection of a flush-mounted body according to the finished thickness of the lining, secure the penetration against construction-site water ingress, prepare a clean substrate for the waterproofer's sleeve and formalise acceptance of the interface through a written record before tiling.

Key takeaways

  • The installation depth depends on the build-up of lining, composite waterproofing and tile with its adhesive.
  • The mounting template and factory boxes define the minimum and maximum permitted dimensions.
  • Test plugs and protective covers must withstand splashes of levelling mortar.
  • A joint inspection record signed before the tiler starts work formally delimits the waterproofing responsibilities.

Determining the axis position and locking the projection of the flush-mounted body

Connecting a flush-mounted mixer tolerates no geometric approximation. A depth error of a few millimetres forces the ordering of expensive specific extensions or, conversely, prevents the finishing rosette from sitting flat against the facing. The projection is always calculated from the axis of the supporting frame or the raw wall, taking into account all the successive layers: the thickness of the reinforced plaster boards or the masonry lining, the liquid waterproofing system layer under tiles assigned to CFC 282, the thickness of the adhesive mortar bed and finally that of the tile or ceramic.

Universal flush-mounted bodies and modern installation boxes have engraved marks showing the permissible "minimum" and "maximum" limits relative to the surface of the laid tiles. The gap between these two marks generally does not exceed 20 to 30 mm. The sanitary installer must obtain the data sheet of the chosen tile as well as the reference level mark or one-metre level line above the finished floor in order to position the axis of the mixer, traditionally set between 100 cm and 110 cm above the shower tray or the tiled floor.

Typical breakdown of a wall thickness in a wet area
Wall componentAverage thicknessEffect on sanitary projection
Metal frame or raw masonryVariable (75 to 150 mm)Rigid fixing support for the box
Moisture-resistant backing board (single or double)12.5 to 25 mmStarting face for the sanitary cut-out
Waterproofing under tiles (CFC 282)1 to 2 mmOverlap zone of the sleeve
Adhesive mortar and ceramic tile10 to 15 mmFinal bearing surface of the rosette

Protecting the outlet, preparing the substrate and recording the interface handover

Once the pressurised pipes are connected and the flushing tests carried out, the flush-mounted outlet body must be sealed and mechanically protected. Installation boxes have rigid plastic protective covers which must remain in place throughout the finishing work. These covers prevent splashes of plaster, adhesive or mineral dust from contaminating the connection threads and the mixing chamber. Synthetic test plugs fitted with O-rings ensure watertightness during the drinking-water pressure test without damaging the conical seats.

The preparation of the substrate around the penetrating body directly determines the success of the waterproofing under tiles carried out under CFC 282. The sanitary installer makes a clean, precisely fitted cut-out in the lining, leaving a maximum perimeter gap of 5 to 10 mm around the box or the factory collar. If the opening has been drilled in solid masonry, the annular void must be carefully filled with a non-shrink repair mortar, struck off perfectly flush with the board or the plaster so as to provide a flat surface that is free of dust and grease.

  1. Fixing and checking plumbSecure the box firmly on its metal crossbar or by mechanical anchoring, then check the horizontal and vertical levels with a straightedge.
  2. Fitting the plugs and pressure testScrew in the factory test plugs to carry out the hydraulic pressure test without the final trim.
  3. Finishing the surrounding bearing surfaceMake good the cut-out opening to present a continuous, clean substrate at the connection collar.
  4. Signing the handover recordCheck the conformity of the projection with the tiler and have the acceptance of the substrate recorded in writing before the membrane is applied.

The most frequent dispute in water damage cases arises from the interface between the flush-mounted sanitary body and the liquid waterproofing sleeve applied by the applicator. If the opening is poorly filled or if the box is not flush within the system supplier's tolerances, the perimeter waterproofing tears under thermal expansion. According to art. 365 para. 3 CO, if a circumstance jeopardises the proper execution of the work, the contractor informs the client. The sanitary installer therefore records, in a dated self-inspection record, the position, alignment and projection dimension of each outlet before the plasterers and tiler start work.

Axis setting, finished projection and waterproofing allowance

Installing a thermostatic mixer or a shower distribution box tolerates no approximation. On a dry-lined or masonry wall, the installation depth of the base body determines the success of all the final fittings. A box fixed too far back prevents the cartridges from being screwed in and the decorative rosette from being clipped on, forcing the installer to order expensive extensions that are often not available at short notice. Conversely, an outlet that projects too far prevents the finishing trim from being pressed against the tiles, leaving an unsightly gap through which spray water penetrates behind the cover plate.

The fundamental reference remains the one-metre level line transferred by the masons. The operating axis of a shower mixer is set between 110 and 120 cm from the finished level of the shower area, while the elbow outlet for the hand shower is generally positioned at 100 cm and the overhead shower between 210 and 220 cm. However, height is not the main risk: it is the cumulative thickness of the wall build-up that causes disputes. The sanitary installer must obtain the exact composition of the wall before mechanical tightening on the rails or fixing bars: thickness of the plasterboard or fibre-cement board, type of liquid waterproofing system, adhesive layer and thickness of the porcelain stoneware or ceramic tile.

Effect of the wall substrate composition on the installation dimension of the flush-mounted box
Base substrateWaterproofing build-up and facingEstimated total thicknessSanitary point of attention
Light metal partition with reinforced plasterboard (2 x 12.5 mm)Liquid-applied waterproofing system under tiles (AUL) + adhesive + thin tile (8 mm)36 to 40 mmPosition the box on its medium-density template to avoid crushing the boards when the screws are tightened.
Masonry of clay brick or calcium silicateCement levelling render (15 mm) + bonded waterproof membrane + large-format porcelain stoneware (12 mm)32 to 38 mmCut a clean chase without bursting the brick cells; wedge the body with rapid-setting mortar without distortion.
Tile-ready backing board of extruded rigid foam (20 mm)Liquid waterproofing membrane with reinforced tape + glass mosaic (4 mm)27 to 30 mmClamp the flush-mounted box on a rigid metal crossbar located at the back of the foam board.

The horizontality and verticality of the box require the systematic use of a precision spirit level on the flats provided by the manufacturer. A fitting body tilted by only two degrees causes a glaring visual offset of the twenty-centimetre square finishing plate once the tiles are laid. This error cannot be corrected on the decorative trim.

Body protection, interface with the tiler and written record

As soon as the hot and cold water pipes have been connected and are under test pressure, the sanitary installer locks the temporary protection of the mechanism. No construction site may leave an internal thread or a cartridge chamber exposed to the open air. Contemporary boxes include a rigid synthetic cover clipped or screwed on at the factory. This component protects the seal seats against splashes of skim plaster, abrasive sanding of plaster and adhesive mortar smears. This cover also serves as a cutting template for the tiler and must under no circumstances be removed before the tiles are laid.

The demarcation of responsibilities between the sanitary installer and the waterproofer or tiler remains the critical point of the warranty on the work. The sanitary installer prepares the substrate: careful filling with levelling mortar around the box body, dust removal and degreasing of the box's adhesion collar. The waterproofer then steps in, laying the membrane or liquid coating with a specific pre-formed elastomer sleeve enclosing the body. The installer does not carry out the waterproofing under tiles, but delivers a rigid base that is watertight under hydraulic test and accessible to receive the sleeve.

  1. Pressure test and ventingCheck the integrity of the pipework and the flush-mounted body under service pressure in accordance with the suissetec technical guidelines. Ensure that there is absolutely no seepage at the crimped or screwed connections.
  2. Locking the plugs and the protective coverCheck that the test plugs are present and the plastic cover is closed. Clean the immediate surroundings of the box to clear the bonding zone of the collar.
  3. Geometric check of the projectionMeasure the distance between the front of the cover and the finished tiled surface mark provided by the site management. Check that the dimension lies strictly within the minimum and maximum range engraved on the template.
  4. Drawing up the interface recordSign a joint inspection record with the site management and the tiler before the liquid waterproofing layer is applied. This document certifies the full conformity of the position, the cleanliness of the body and the integrity of the protection.

The written record releases the sanitary company from any liability relating to subsequent damage to the box, fouling by mortar or a non-compliant cut of the waterproofing membrane. If the tiling conceals a misaligned outlet or if another trade forces the mechanism without prior notice, the traceability of the signed document is the only enforceable technical evidence at the final settlement of the construction site.

Managing projection deviations and rework protocol before tiling

When the actual thickness of the adhesive and tile build-up differs from the allowance drawings or when the plasterboard lining is out of plumb, the flush-mounted shower outlet ends up outside tolerances. Two deviations occur: the flush-mounted body sits too deep, preventing the watertight screwing of the rosette or the outlet elbow, or the body protrudes excessively from the finished tiling, preventing the finishing ring from coming up against the facing.

  1. Measuring the offset against the level lineCheck the centre distance and the rough projection against the metric height mark and the projected line of the finished tiling approved by the site management.
  2. Fitting the certified mechanical extensionIf the body is recessed by less than 30 millimetres too deep, fit the extension kit certified by the fitting manufacturer, including O-rings and extended screws. Beyond that, loosen the rail fixing bracket to bring the block forward.
  3. Ensuring the formal stoppage of workIf the body protrudes beyond the theoretical finished surface, require the framing or lining to be modified. Draft a written notice to the site management with a copy to the tiler in accordance with the Code of Obligations (CO), suspending the application of the waterproofing under tiles until full rectification.

The cost of reworking a flush-mounted plate after the liquid waterproofing resins have dried far exceeds that of a realignment on the raw rail. The technical correction always involves checking the air- and watertightness of the penetration before signing the interface handover record, which relieves the sanitary installer in favour of the applicator of the system under tiles, in accordance with the general rules of standard SIA 118.

Frequently asked questions

What should be done if the projection of the installation box is set back from the finished tile surface?

If the setback remains within the manufacturer's adjustment range, fit an original axis extension equipped with new seals. If the depth exceeds this tolerance, refuse makeshift stacked threaded fittings: report the anomaly to the site management in writing, open the back of the service partition if accessible or modify the wedging of the support frame before any tiling begins.

Who must cut the plastic protective template of the flush-mounted box?

The plastic or polystyrene protective template must remain intact throughout the liquid waterproofing work under tiles. It is cut only after the tile joints have dried, with a cutter, flush with the laid tile. This cut is generally the tiler's job when applying the sleeve, or the sanitary fitter's when installing the final mechanical trim.

How should one react if the tiler has applied the liquid waterproofing without the sanitary waterproofing collar?

Stop all further work immediately and refuse to install the finishing fitting. The absence of the elastomer collar connected to the installation box guarantees water ingress into the partition if the external silicone joint leaks. Send a formal notice of defects to the site management: the tiler must remove the adjacent elements and redo the waterproofing under tiles properly.

What items should be recorded on the interface record before the tiler starts work?

The jointly signed document must state: the standardised centre distance, the plumb checked with a tubular level, the projection value relative to the raw surface of the substrate, the presence of the test plugs screwed in under hydraulic pressure, the absolute integrity of the protective covers and the availability of the pre-formed waterproofing sleeves suited to the box. Attach dated photographs of all the outlets without fail.

Texts and standards cited

  • norme SIA 118General conditions for the execution of construction work concerning interface handover, notices of defects and acceptance of the work.
  • code des obligationsGeneral rules governing the contract for work and services, the contractor's obligations and the duty to notify in case of a risk of defect in the work.

In the same section