Skip to content
Website
🧱 CFC 250Appliances, connections and built-in fittingsChapter 6 of 10 in the section

The kitchen: manifold, isolating valves, waste outlet and space for the furniture

Installing water and waste stubs without a validated kitchen fitter's plan exposes the construction site to heavy rework. You will learn how to lock down the essential dimensions before core drilling, how to position accessible isolating valves, and how to fix the sound-insulated waste outlet within the free volume of the sink base unit without blocking drawers or constraining built-in appliances.

Key takeaways

  • Always demand the kitchen fitter's technical layout plan before drilling the slab or the partition.
  • Do not allow any technical stub to protrude directly behind the position of a fully integrated dishwasher.
  • Set the axis of the waste outlet between 450 and 500 millimetres above the finished floor level.
  • Group the manifold or the isolating valves under the sink to guarantee quick individual shut-off.

The final kitchen fitter's plan: the absolute reference before any drilling

Installing plumbing stubs in a kitchen from the architect's 1:50 plan alone almost always leads to integration failure. Modern kitchen fitting relies on modular elements accurate to the millimetre: base units with deep-pull runners, waste drawers suspended under the bowl, or fully integrated dishwashers flush with the splashback. If the waste outlet or the water supplies come out outside the narrow dead space reserved by the manufacturer, the kitchen fitter cuts the back panels, removes a drawer or demands that the pipes be moved when the wall tiling has already been grouted.

Constraints on stub positions according to the kitchen furniture
Kitchen elementPermitted zone for connectionsMain furniture constraintRisk if the dimension is wrong
Sink base unit (600 to 900 mm)Centred in the carcase, between 450 and 550 mm from the finished floorClearance for waste drawers and stainless steel or composite bowlCollision with the runner mechanism or the trap
Fully integrated dishwasherNo stub behind the appliance; offset to the sink unitFull installation depth with no service voidAppliance protruding by 50 mm relative to the worktop
Low pan drawerProhibited, unless fully recessed in the masonryDrawer back receding to 30 mm from the finished wallDrawer stop blocked or destructive cutting of the wood
Refrigerator with water dispenserIn the plinth or set back in a recess boxLow ventilation and rear compressorCrushing of the supply hose or overheating

The technical plan supplied by the kitchen fitter states precisely the "technical installation zone". This zone forms a horizontal and vertical band where protrusions are tolerated. To secure the plumber's work, dimensions must always be referenced to the official 1-metre level line marked with a chalk line on the structural work, taking into account the thickness of the sound insulation, screed and floor covering build-up.

Manifold, dedicated isolating valves and waste outlet height

In a communal or individual kitchen, every consuming fixture must have a means of shut-off operable without tools. Installing a mini-manifold or recessed boxes fitted with angle isolating valves with integrated filters guarantees this independence. The plumber arranges the cold and hot water supplies symmetrically, with hot water conventionally on the left, spaced 80 to 150 mm from the cold water depending on the intended terminal tapware.

  1. Checking axes and setting outTransfer the 1 m level line. Mark the width of the sink base unit from the validated kitchen fitter's plan. Set out the axis of the waste outlet and mark the hot and cold water outlets at equal distance from the central axis.
  2. Fixing the drinking water stubsSeal or screw the connection boxes for multilayer or PE-Xc pipes onto a rail. Position the water connections between 550 and 600 mm above the finished floor. Fit a double-outlet isolating valve on the cold water for the dishwasher.
  3. Installing the sound-insulated waste socketInstall the waste pipe in cast iron or sound-insulated plastic pipe of nominal diameter 56 mm. Finish flush with the wall face with an airtight plug with elastomer seal or an adapter socket for a swivel trap.
  4. Pressure test and gauge checkPut the pipes under test pressure in accordance with the SSIGE guidelines. Fit construction site protective caps and check that there is no obstacle within the insertion envelope of the furniture.

A waste outlet installed too low prevents the correct connection of a macerator or limits the water seal of a space-saving trap. Installed too high, beyond 520 mm from the finished floor, it works against the connection gradient of the undermount bowl, creating permanent standing water and greasy deposits in the tailpipe. The plumbing foreman checks these levels before the screed layers come in, so as to correct slab penetrations without destructive chiselling.

Provisions for built-in appliances: the impossible technical void

The classic error on new housing construction sites is to position the water and waste stubs directly in the theoretical axis of the dishwasher or steam oven. Modern built-in appliances, in particular 60 cm wide fully integrated dishwashers, occupy the entire volume of the recess, i.e. a usable depth of 550 to 570 millimetres for a standard 600 millimetre worktop. Installing an angle valve, a water tap point or a waste socket on the raw partition within this footprint mechanically prevents the appliance from being pushed fully home, leaving the unit front protruding from the general alignment of the kitchen.

All isolating valves, distribution branches and waste traps dedicated to the machines must absolutely be offset into the neighbouring carcase housing the sink. This sink base volume is the only accessible zone where the presence of a suspended bowl leaves enough clearance to operate the isolating valves in the event of a leak and to connect the flexible supply and waste hoses without creating a crushed bend. The kitchen joiner then makes a clean hole-saw opening in the side panel of the sink base unit, flush with the technical back.

For the dishwasher waste, a direct tapping onto the sink trap tubing by means of a barbed connector with integrated non-return valve remains the usual method. Where the configuration requires an independent waste stack in the sink base unit, it must be made in sound-insulated waste pipe of 40 or 50 millimetre diameter, discharging at a minimum height above the overflow level of the sink, to prevent any gravity backflow of greasy water into the dishwasher.

Island connections and coordination with the furniture base

In configurations with a central island, the plumbing pipes have no wall lining to conceal adjustments. The stubs pass directly through the raw concrete slab or run in the technical void under the screed before coming through the finished floor. The exit point must fall strictly within the technical carcase provided by the kitchen layout, without encroaching on the position of the unit's adjustable feet or conflicting with full-extension pan drawers, which often come down to within a few centimetres of the carcase base.

Typical positions and levels of kitchen plumbing stubs
Appliance or draw-off pointMandatory installation zoneAxis height above finished floor (FFL)Recommended connection diameter
Sink tapware (cold / hot water)In the sink base unit, centred on the bowl550 to 600 mm3/8'' male thread or 1/2'' angle valve
Sink and dishwasher waste outletIn the sink base unit, offset by 100 mm450 to 500 mmPE-HD socket or Geberit Silent Ø 56 / 63 mm
Dishwasher / washing machine supplyIn the sink base unit (never behind the appliance)550 to 650 mm3/4'' male appliance isolating valve
Built-in steam oven / steamerIn adjacent carcase or accessible technical plinth300 to 400 mm1/2'' angle valve with 3/4'' connector
Island stub (water and waste)Defined footprint of the internal technical carcaseRaw outlet 100 mm above the screedWaste Ø 56 mm min. + water pipes in conduit
  1. Validation of the kitchen fitter's provision planRequest the dimensioned technical layout plan from the kitchen supplier, expressly stating the width of the carcases, the position of the vertical partitions and the exact depth of the lower drawers.
  2. Setting out on the floor from the level lineTransfer the exact axis of the sink base unit onto the raft or raw slab, referring to the planned finished walls and taking into account the thickness of the plasterboard lining or the levelling screed.
  3. Installing and protecting the stubs before the screedFix the passage bends firmly with acoustic clamps and close the ends with watertight protective caps to prevent any ingress of laitance during pouring of the screed.
  4. Checking gauges on acceptance of the structural workCheck the conformity of the levels and squareness of the outlets before the kitchen fitter starts, so as to correct out-of-plumb faults without having to cut back into the floating screed.

Managing installation conflicts and remedial measures from below

When the connection comes out in the wrong place for lack of a validated kitchen fitter's plan, the conflict is generally discovered when the carcases are installed. The most critical case remains the water or waste stub coming out directly behind a fully integrated dishwasher or a low pan drawer. These appliances offer no rear technical void: the sheet metal sits flush with the finished partition to within two millimetres. If the pipes emerge in this space, the appliance refuses to go into its recess, blocking the alignment of the fronts and the installation of the worktop.

The first measure on the construction site is to record the finding with the site management and the joiner before any rough cutting of the rear panels. Any alteration of the carcase by the kitchen fitter weakens the unit and affects its factory warranty. Two technical remedial options are available depending on the progress of the screeds and the nature of the partition. If the wall is plasterboard on a metal frame, a targeted opening of one panel between two studs makes it possible to move the distribution manifold back or to shift the waste tee towards the axis of the sink base unit.

  1. Low diversion in the plinth zoneCut the supply pipes from below and divert the pipework into the plinth void, generally 80 to 100 millimetres high, to enter through the open back of the sink unit.
  2. Correcting the waste gradientIf the waste socket is too high for the deep bowl of an undermount sink, fit a short bend and extend the waste pipe through the plinth to the adjacent carcase.
  3. Offsetting the isolating valvesExtend the multilayer branches to place the angle isolating valves and the solenoid valve in a zone accessible without tools, imperatively within fifty centimetres of the door.

Frequently asked questions

What should be done if the waste outlet is too high for an undermount sink?

An undermount bowl sits a further twenty millimetres below the granite or composite. If the wall waste outlet is more than 500 millimetres above the finished floor, the flat trap can no longer ensure the minimum water seal without backing up towards the bowl. The only reliable solution is to open up the partition and lower the PE-HD or Geberit Silent socket to 450 millimetres, otherwise continuous standing water will result.

Where should the supply for a built-in dishwasher be positioned if there is no service void?

As the appliance occupies the full depth of the unit up to the raw wall, no valve or wall trap may appear within its sixty-centimetre footprint. The cold water stubs and the waste connection must be offset sideways into the neighbouring carcase housing the sink. The water supply pipe and the waste hose pass through the side panel of the unit via a deburred opening.

Why prohibit installing plumbing stubs from a provisional architect's plan?

Architect's 1:50 plans show a layout intention but ignore the real widths of filler strips, the final thickness of the worktop and the plinth heights chosen by the manufacturer. A ten-centimetre shift places a manifold under the axis of an intermediate unit partition. Requiring the kitchen fitter's technical layout plan with written validation by the site management avoids costly corrective core drilling.

How can accessibility of the isolating valves be guaranteed under a very crowded sink?

Between the waste disposer, the drawer-mounted recycling system and the additional instantaneous water heater, the sink base volume is saturated. The manifold and valves must be fixed laterally on the partition, between 350 and 450 millimetres from the finished floor, turned towards the opening. If a drawer slides out at the front, the operating handles must remain graspable without having to remove the waste bin.

Texts and standards cited

  • norme SIA 118General conditions for the execution of construction work and handling of notices of interruption or modification of the works
  • directives SSIGE W3Guidelines for drinking water distribution installations, requirements for sizing, isolating valves and protection against backflow

In the same section