Skip to content
Website
🧱 CFC 250Cold water, hot water and recirculation distributionChapter 10 of 10 in the section

Limiting the temperature at the draw-off point: thermostatic mixer, setting and sensitive uses

This chapter covers the positioning, calibration and checking of thermostatic mixers in sanitary distribution. You will learn to reconcile the bacteriological hygiene requirement of sixty degrees in the storage cylinder with protection against scalding at the draw-off points. You will be able to size the mixing device, secure sensitive uses such as nurseries and record your settings in a report.

Key takeaways

  • Maintaining sixty degrees in sanitary storage eliminates the risk of legionella growth in the installation.
  • A central or terminal thermostatic mixer limits the mixed water to fifty or forty degrees depending on the use of the building.
  • Nurseries and medico-social institutions require strict mechanical limiting to protect vulnerable users.
  • Systematic recording of temperatures with an immersion thermometer ensures a compliant commissioning report.

Reconciling thermal shock and skin safety: the central role of the thermostatic mixer

The sanitary installer faces a permanent physical contradiction when designing and installing distribution networks. On the one hand, legionella prevention requires domestic hot water to be stored at a temperature equal to or above sixty degrees in the water heater or storage cylinder, in accordance with the hygiene requirements of SIA 385/1. On the other hand, water distributed at such a temperature causes a third-degree skin burn in an adult in less than five seconds, and almost instantaneously in an infant.

Fail-safe thermostatic mixer
A mechanical or electronic device that regulates the mixing of hot and cold water to deliver mixed water at a constant value. It incorporates a wax-cartridge or bimetallic mechanism that shuts off the flow of mixed water if the cold water supply fails.

To solve this equation without compromising sanitary prophylaxis, the thermostatic mixer acts as an impassable technical barrier. Installed directly at the outlet of the water heater or at the start of a distribution substation, it mixes the very hot stored water with a fraction of cold water from the drinking water network. The volume circulating in the main loop or routed to the floor manifolds is thus immediately brought down to a stabilised nominal value, limiting accelerated scaling of the terminal pipes.

On risers fitted with a hot water circulation loop, the circulation return must be managed rigorously. The head thermostatic mixer must be connected according to a four-way diagram or be fitted with a bypass with a certified non-return valve to prevent lukewarm return water from disturbing the sensitivity of the thermostatic cartridge. A faulty hydraulic configuration causes differential pressure oscillations and unwanted temperature fluctuations at the most distant taps.

Limiting protocols, early-childhood facilities and recorded acceptance

In buildings housing vulnerable persons such as nurseries, kindergartens and medico-social institutions, the risk of scalding requires a drastic lowering of the set point. The maximum temperature permitted at the draw-off point for hand washing and showers is set at forty degrees, or even thirty-eight degrees according to the cantonal regulations applicable to early childhood. Since young children's avoidance reflexes are incomplete, water at fifty degrees causes serious injuries in about ten seconds.

  1. Bringing the circuit hydraulically up to operating conditionsCheck that the hot water cylinder temperature is stabilised at sixty degrees and that the dynamic pressure of the cold water network is balanced with that of the hot water circuit.
  2. Setting the mechanical stop ringRemove the cover or protective handwheel of the centralised mixer. Turn the micrometric calibration screw until a constant forty degrees is obtained, measured with a thermometer with certified calibration.
  3. Tamper-proof locking of the operating elementSnap on the notched locking ring and seal the cover with a lead seal or an anti-tamper clip to prevent any modification by the users of the site.
  4. Instantaneous cold water cut-off testClose the cold water isolation valve upstream of the mixer. The residual hot water flow must drop below the dripping threshold in less than one second to confirm anti-scald safety.
Exposure time causing a severe skin burn according to domestic water temperature
Water temperature at draw-offSkin effect on adult skinSkin effect on child's skin (nursery)Use permitted according to SIA 385/1
65 °CDeep burn in 1.5 secondsInstantaneous third-degree burnProhibited at draw-off (storage only)
60 °CDeep burn in 5 secondsSevere burn in 1 secondWater heater storage and disinfection
50 °CTolerance of more than 2 minutesSkin injury from 10 to 15 secondsMaximum permitted in collective housing
38 °C to 40 °CNo risk of injuryTotal absence of thermal dangerMandatory in nurseries and care facilities

Recording the setting data is the contractual element that guarantees proper execution of the work under the Code of Obligations (CO). The sanitary team leader records in a self-inspection report the date of the intervention, the initial temperature at the hot water heater, the value calibrated on each mixing bank and the response time of the safety cut-off. This document is countersigned by the site management at acceptance of the installations and appended to the operating file handed over to the client.

Hydraulic architecture: substation mixer and terminal mixers

The design of domestic hot water networks according to SIA 385/1 is based on a clear separation between energy transport and delivery at the draw-off point. To neutralise the risk of legionella, the set-point temperature at the generator and in the primary loop must remain permanently at a level equal to or above 60 °C, with a circulation return not dropping below 55 °C. Conversely, the skin integrity of users, particularly in school, medico-social and early-childhood premises, requires a strict cap at the tap outlet. This dual technical requirement rules out any direct compromise on production and shifts the obligation to lower the temperature onto dedicated thermostatic devices, judiciously inserted in the distribution diagram.

Two types of installation compete on the construction site: the centralised thermostatic mixer in a distribution substation or at the foot of the riser, and the decentralised mixer placed under each sanitary fixture or integrated into the tap body. The choice directly determines the microbiological safety of the terminal network. Distributing mixed water at 38 °C or 40 °C over long linear pipes creates an ideal thermal zone for bacterial growth. This is why collective mixed-water distribution requires the volume of water downstream of the control device to be limited to the strict minimum, respecting the rule of a maximum of three litres of stagnant water per section without circulation loop.

Comparison of thermostatic device installation options according to distribution constraints
ConfigurationHydraulic installationSanitary advantagesOperating constraints
Central riser mixerIn the service shaft, connected to the DHW flow at 60 °C and the cold waterSecures several wet rooms or washbasin banks simultaneouslyMixed water at 40 °C must not be circulated in a loop; very limited downstream volume
Thermostatic mixer under basinFitted on the supply hoses under the washstandKeeps the water at 60 °C right up to the foot of the sanitary fixtureMore non-return valves and increased cartridge maintenance
Terminal thermostatic tapExposed or concealed tap with integrated mechanical stopImmediate protection at the point of use with lockable settingCartridge directly exposed to scaling from both cold and hot water

Calibration procedure, recording of limiting and traceability

Anti-scald safety does not rely on the manufacturer's graduated markings but on an actual physical measurement taken with the real water flow present. A thermostatic cartridge reacts to the balance of dynamic pressures between sanitary hot and cold water. Any hydraulic imbalance not compensated by upstream pressure regulators distorts the mixing. The setting of the mechanical stop must always be adjusted in situ, using a calibrated instant-reading thermometer, at the nominal flow rate of use.

  1. Bringing the network up to thermal operating conditionsOpen the upstream draw-off points to ensure that the main loop supplies the mixer with sanitary water stabilised at its contractual nominal temperature (minimum 60 °C at the flow).
  2. Thermometric measurement at the jetDraw water at full flow for 60 seconds. Immerse the measuring probe in the direct flow under the spout and adjust the internal notched ring of the cartridge until the required limit value is stabilised.
  3. Mechanical locking and sealLock the stop screw or the mechanical stop pin. On collective installations or in nurseries, fit a tamper-proof cover or a plastic lead seal to prevent any modification by users.
  4. Cold water failure testSuddenly close the cold water isolation valve supplying the mixer: the cartridge must instantly cut off the hot water flow to rule out any risk of scalding spray.

The thermal readings must be rigorously transcribed in a sanitary commissioning report handed to the site management and the building operator. This document specifies the identification of the device, the room served, the mixed water temperature measured and the type of physical locking applied. The non-return valves integrated upstream of the mixer are an integral part of this check: a leaking valve causes hot water backflow into the cold water network, producing unwanted temperature rises at neighbouring WC cisterns or taps.

Managing thermal drift and urgent corrective measures

When a temperature reading shows mixed water exceeding the set-point value at a sensitive draw-off point, in particular in a nursery, a school or a medico-social institution, the sanitary installer must intervene without delay to secure the installation. Water distributed above 40 °C at a fixture accessible to children presents a risk of severe burns within seconds, which formally contradicts the body-protection rules arising from SIA 385/1. The first technical measure is to temporarily shut off the tap concerned or to close its individual isolation valves under the basin to prevent any water being drawn until the fault has been fully identified.

The technical diagnosis mainly targets three recurring causes. Firstly, failure of the non-return valves integrated in the mixer connections: under the effect of limescale or unfiltered construction site debris, these valves lose their tightness and create a hydraulic bridge between the cold and hot water distribution, distorting the overall regulation of the cartridge. Secondly, seizing or ageing of the wax-element thermostatic cartridge, which is unable to compensate for flow demands. Thirdly, a marked mismatch of the dynamic supply pressures upstream of the device.

  1. Cleaning and checking the valvesHydraulically isolate the mixer, remove the strainer filters and check the tightness of the non-return valves; replace without hesitation any component damaged by limescale.
  2. Checking the thermostatic cartridgeReplace the thermostatic regulation mechanism if the cartridge shows set-point drift or if the anti-scald safety device does not instantly cut the flow when the cold water is interrupted.
  3. Stabilising upstream pressuresMeasure the dynamic service pressures with a pressure gauge and balance the network by installing a pressure reducer if the upstream difference exceeds one bar.
  4. Recalibration and joint checkCarry out a full recalibration with a calibrated thermometer and check that the temperature holds perfectly under several successive flow regimes.

Every completed corrective action must be recorded in writing on a non-conformity sheet and entered in the building's sanitary maintenance log. The mechanical limiting ring is relocked, then secured with a cover that cannot be removed without special tools, in order to prevent any uncontrolled tampering by users. The installer sends the updated test report to the site management and to the nursery management, certifying that the thermal conditions on the site are fully under control.

Frequently asked questions

What should be done if the temperature at a nursery tap exceeds 40 °C during the acceptance inspection?

The installer must immediately take the water point out of service by closing its isolation valves under the basin to rule out any risk of accident. He then checks the position of the internal mechanical limiting ring. If the physical lock is correctly positioned, the problem most often comes from a defective thermostatic cartridge or fouled upstream valves. After cleaning or replacing the components, a new joint thermometric check is carried out and validated in the acceptance report.

Why does lukewarm water flow back into the cold water network near the mixer?

This backflow indicates failure of the non-return valve fitted on the hot water inlet of the mixer. When the pressure of the domestic hot water is higher than that of the cold water, the hot water passes the leaking valve and contaminates the cold drinking water pipe. This hydraulic bridge warms the cold water pipes, promoting bacterial growth. The connection must be isolated, the valve seats cleaned and the defective valve cartridge replaced.

How can thermal disinfection of the circulation loop be reconciled with protection against scalding?

Production and the circulation loop must be maintained at a temperature of at least 60 °C according to the rules of SIA 385/1 in order to destroy legionella. To protect users at the points of use at the same time, a centralised thermostatic mixer or mechanically limited terminal mixers are installed. In this way, the water circulates at high temperature in the main hygiene loop but is automatically mixed with cold water before leaving the tap at a harmless temperature.

How often must the calibration and limiting of the mixers be checked in operation?

In buildings housing sensitive groups, such as nurseries and hospitals, an annual check of the distribution temperature at the draw-off point is recommended as part of sanitary maintenance. The technician measures the maximum temperature at the tap fully open and tests the emergency shut-off by cold water failure. The values recorded must be systematically entered in the building's sanitary log to prove that the mechanical safeguards in place are being maintained.

Texts and standards cited

  • norme SIA 385/1Domestic hot water installations in buildings - General principles and requirements

In the same section