Drainage: stack, primary ventilation and sound insulation: the execution reference
This section is aimed at sanitary installers, lead fitters and foremen dealing with gravity drainage requirements in buildings. It brings together the rules for sizing, air-flow routing and acoustic installation, to ensure smooth flow, eliminate structure-borne noise and maintain the integrity of the water seals without ever causing backflow into the neighbours' premises.
- 10chapters
- 22 000words
- 6sections in the training course
- 60chapters in total
Key values to remember 4
50 mm
Minimum water seal height for a sanitary fixture trap
1 %
Usual minimum gradient for a horizontal drainage collector
0.5 bar
Resistance of socket joints to temporary overpressure without disconnection
25 to 30 dB(A)
Usual installation sound level requirement for sleeping rooms
Technical scope of internal drainage and installation interfaces
The internal gravity drainage system ensures the unobstructed passage of domestic wastewater and soil water from the fixture outlet to the exit of the building envelope. Design and installation comply with the requirements of SN EN 12056 for hydraulic and air-flow behaviour, and with the noise protection requirements of SIA 181. The sanitary installer is responsible for the choice of internal diameters, the geometry of branch connections, the vibration damping of the clamps and the air circuit that ensures the stability of the traps.
The installer's responsibility ends at the outer face of the foundation slab or basement wall crossed by the watertight sleeve. External buried collectors, trenches and inspection chambers at the plot boundary fall under civil engineering and drainage contractors. Likewise, if the route passes through a reinforced concrete load-bearing slab, the sanitary installer provides the openings and fits the approved fire-stopping sleeve, but does not alter the structural reinforcement without the written consent of the civil engineer, in accordance with the rules of the contract for work and services under art. 365 CO in the event of an unforeseen obstacle.
- Included: drainage stacks, 45° branches, acoustic Y-junctions, secondary and primary ventilation, horizontal collectors suspended in the basement.
- Included: internal lifting devices, non-return valves for fixtures below the backflow level and clamps with elastomer lining.
- Excluded: air ducts for controlled mechanical ventilation (CFC 244) and floor waterproofing of wet rooms (CFC 282).
- Excluded: excavations, external gravel bedding and connections to the public sewer (CFC 201 and CFC 411).
Logical reading order and operational progression
Building a high-performing gravity system leaves no room for improvisation. A trap that loses its seal or a hydraulic knock against a partition almost always results from poor coordination between the gradient, the air venting and the mechanical decoupling. We propose a structured ten-step path to master the work, from rough setting-out to handover without defects.
- 1. Master the flow dynamicsChapters L4-01 and L4-02 lay the foundations: setting the gradient to prevent the separation of solids, and guaranteeing the primary air flow that prevents siphoning of the traps located lower down.
- 2. Isolate sound transmissionChapter L4-03 details the SIA 181 standard: use of heavy mineral-filled wall pipes, acoustic clamps with decoupled fixed point and insulation of the bends at the stack base.
- 3. Protect the fixtures and their connectionsChapters L4-04 and L4-05 deal with the regulatory water seal height, the risks of evaporation and the sizing of shared collectors receiving several neighbouring fixtures.
- 4. Manage risk areas and special pointsChapters L4-06, L4-07 and L4-08 cover lifting below flood level, the strict separation of the wastewater/rainwater networks required by water protection regulations and the fire-stopping of slab openings.
- 5. Diagnose, unblock and remediateChapters L4-09 and L4-10 provide the method of investigation by camera or mechanical drain rod in the event of blockages, as well as the systematic tracing of returning foul odours.
By following this logic, the fitter prevents sound-insulation disputes and complaints about sewer odours from the moment of commissioning. Rigorous application of geometric tolerances and compliance with the standards guarantee quiet, durable installations that are easy to inspect during maintenance operations.
📘 Chapters in this section 10
Gradient: the useful minimum, excessive gradient and deposits in the pipe
Set the ideal gradient to carry away heavy solids without ever leaving the bottom of the collector dry.
Drainage: stack, primary ventilation and sound insulationVenting the stack: primary ventilation, negative pressure and the trap that empties
Calibrate the primary ventilation to stop whistling and siphoning of the connected fixtures dead.
Drainage: stack, primary ventilation and sound insulationSilencing the stack: sound-insulated pipe, brackets with isolating lining and cladding
Neutralise drainage impact noise with decoupled fixings and certified acoustic pipes.
Drainage: stack, primary ventilation and sound insulationThe water seal: height, evaporation in an empty dwelling and diaphragm trap
Maintain a tight water seal even after several weeks of prolonged vacancy of the dwelling.
Drainage: stack, primary ventilation and sound insulationConnecting several fixtures: distances, diameters and mutual suction effect
Arrange your branch connections without risking the loss of a shower trap's seal when a neighbouring cistern is flushed.
Drainage: stack, primary ventilation and sound insulationDraining below the collector level: lifting station, non-return valve and pumped discharge
Protect basements against backflow from the public sewer by choosing the appropriate lifting station.
Drainage: stack, primary ventilation and sound insulationTwo networks: separation at plot level, inspection chambers and incorrect connections
Avoid any connection error between the rainwater and wastewater networks when crossing the plot boundary.
Drainage: stack, primary ventilation and sound insulationPassing through a slab: fire-stop sleeve, sealing and acoustic decoupling
Guarantee fire resistance and sound insulation when passing through each load-bearing slab.
Drainage: stack, primary ventilation and sound insulationA blocked drain: locate, clear, inspect and find the cause
Quickly clear stubborn deposits with the appropriate mechanical drain-cleaning tools without perforating the pipe.
Drainage: stack, primary ventilation and sound insulationThe smell that keeps coming back: trap, ventilation, WC pan seal, in that order
Methodically identify the exact origin of odour returns between a dry seal, a blocked vent and a trap.
