Skip to content
Website
🧱 CFC 250Water hygiene: legionella, temperatures and stagnationChapter 4 of 10 in the section

Thermal shock: procedure, duration, burn risk and informing occupants

This chapter details the complete organisation of a curative thermal shock in drinking water networks. You will learn how to structure the information given to users, define intervention windows without any risk of accidental contact, run the flushing outlet by outlet at 70 °C and coordinate human and technical monitoring on the construction site to protect occupants and installers.

Key takeaways

  • Prior written notices distributed to every occupant eliminate any risk of serious bodily burns.
  • The employer applies art. 3 OPA to ensure the protection of sanitary fitters and third parties.
  • The technical protocol requires seventy degrees continuously for three minutes at each draw-off point.
  • The presence of a pair of sanitary installers secures the circulation loop and the draw-off areas.

Prior written notice and setting the intervention windows to prevent accidents

In Swiss residential or office buildings, thermal disinfection is a curative shock intervention against a proliferation of Legionella in the domestic hot water network. While the technical guidelines of the Swiss Gas and Water Industry Association govern normal distribution in order to limit scaling and the risk of bodily harm, raising the water to seventy degrees turns every tap into a severe hazard. At this temperature, skin contact of less than one second causes a third-degree thermal burn requiring hospital treatment. The sanitary installer cannot rely on simple verbal coordination with the property management or the caretaker: the intervention requires formal written notification, distributed to letterboxes and posted on the landing doors at least seventy-two hours before the operations begin.

Vulnerability of human skin to domestic hot water
Water temperatureTime before serious burnEffect on the skinOperational risk level
50 °CMore than 5 minutesSimple erythema without permanent damageSafe distribution zone
60 °CApproximately 3 to 5 secondsSuperficial or partial-thickness burnUsual cylinder outlet threshold
65 °CApproximately 2 secondsDeep second-degree burnHigh danger for vulnerable persons
70 °CLess than 1 secondIrreversible tissue destructionDanger of acute bodily injury

The time slot must target periods of very low demand, generally mid-morning between nine o'clock and eleven thirty, or planned night shifts in residential accommodation buildings. The information notices state the ban on drawing water, including at the cold water tap, where heating by conduction or a return of superheated water remains possible in narrow service ducts. The document gives the on-call contact details of the sanitary foreman on site and asks users to lay shower heads at the bottom of bathtubs beforehand to guard against steam splashes.

Holding 70 degrees, methodical flushing and monitoring of draw-off points

The thermal bactericidal action rests on a strict temperature-time relationship: the distributed sanitary water must reach seventy degrees Celsius at every draw-off point and flow continuously for three minutes. For the CFC 250 sanitary installer, the operation starts with the temporary bypassing of the central thermostatic mixing valves that normally limit the flow temperature to the dwellings. At the foot of the riser, monitoring is carried out with a calibrated digital pipe-contact thermometer or an immersion probe fitted on the drain valve.

  1. Physical locking-off of public access pointsFitting construction site barrier tape and locking collars on the taps of common rooms, shared laundries and workshop showers accessible to third parties.
  2. Checking the starting temperature levelTemperature check on the sanitary distribution and confirmation that the circulation loop passes the stable threshold of seventy degrees before the floors are opened.
  3. Methodical draw-off of the terminalsProgressive operation carried out by the sanitary fitters, from the riser closest to the distribution to the furthest apartment, with the mixer set to hot water.
  4. Cross-checked measurement and recordingKeeping the temperature probe in the flow at the aerator for three full minutes, entering the readings on the protocol and closing slowly to prevent water hammer.

Monitoring in the field absolutely requires two qualified sanitary fitters. One technician runs the purges and the temperature measurements while the second monitors the risers in the service duct, checks the stability of the pressures and physically prevents an absent-minded resident from approaching a draw-off point. Personal protective equipment is essential: long neoprene gloves proof against moist heat, a full face shield against scalding aerosols and a protective apron. Any end tap that fails to hold the seventy-degree set value has its aerator removed immediately or is reported for replacement of a scaled-up cartridge.

On-site signage, locking-off of outlets and protection under the OPA

Injecting high-temperature water into an occupied network without physically marking the hazard directly exposes users to a major bodily injury. Even if a general notice was distributed beforehand, occupants frequently forget. The sanitary team must secure the common areas and temporarily disable the most sensitive draw-off points, starting with shower cubicles, sports changing rooms and shared laundries.

  • Posting fluorescent yellow and red notices on every landing door, in lift cars and above the banks of letterboxes, reminding people not to touch the mixers.
  • Mechanical locking-off of the taps accessible to uninformed third parties or children, using lock-off caps secured with a cable tie or an operating padlock.
  • Systematic removal of shower heads and shower hoses in the common areas, temporarily replaced by plugs or drain hoses directed to the drain to prevent any accidental spraying.
  • Fitting red adhesive warning tags directly on the mixer spouts of laundries, workshops and floor sinks.

Presence on site must be organised as a coordinated pair. A first installer remains stationed in the basement to monitor the production of domestic hot water, the pressure gauges and the circulation pumps, while the second fitter goes through the floors equipped with a reliable radio link. This organisation makes it possible to stop the circulation of superheated water instantly if a sudden leak at a seal or a hose failure were to occur under the effect of expansion.

Instrumented flushing, contact time and handover protocol

To effectively eradicate the pathogenic flora attached within the biofilm without prematurely damaging the synthetic pipes or the pressed fittings, the temperature set value and the contact time must be strictly observed. According to the recognised rules of sanitary engineering in Switzerland, the distributed water must reach a level of seventy degrees Celsius at every point of the route. Once this temperature is stabilised at the draw-off outlet, the continuous flow must be maintained for three full minutes.

Contact time before deep skin burn depending on water temperature
Water temperatureTime to a 3rd-degree burnImmediate consequence for the user
50 °CApproximately 5 to 10 minutesSharp sensation of heat without immediate injury.
55 °CApproximately 15 to 30 secondsNatural withdrawal reflex, risk of superficial redness.
60 °CLess than 5 secondsSevere skin injury if the limb stays under the jet.
65 °CLess than 2 secondsAlmost instantaneous destruction of the epidermis.
70 °CLess than 1 secondSerious deep thermal burn on immediate contact.
  1. Instrumented check of each terminalMeasure the temperature with a calibrated digital thermometer with an immersion or surface probe. Record the exact value at the tap spout on the tally sheet as soon as seventy degrees is reached, then time the flow for three minutes.
  2. Depressurisation and thermal dischargeAs soon as the flushing of the last riser is complete, switch off the superheating of the sanitary water. Circulate the cooled water and open the low purge points until the general temperature of the network falls below fifty degrees at the tap.
  3. Checking the thermostatic cartridgesTest the operation of the collective mixing valves or floor thermostatic mixers. High temperatures can cause mechanical jamming of the wax regulating elements or suddenly scale up the built-in non-return valves.
  4. Lifting the lock-off and sign-offRemove the warning signs, refit the carefully disinfected shower heads and sign the operation report with the property management or the building's representative to formally close the procedure.

Handling unforeseen events, thermal failures and the emergency protocol

A thermal disinfection operation involves a significant hydraulic uncertainty. Even with written information given to occupants forty-eight hours in advance and notices posted at the foot of the riser, a person may open a tap without precaution or a faulty mixer may let very hot water through. As soon as an incident occurs or a thermal anomaly appears on the network, the sanitary team applies a strict shutdown and securing procedure in accordance with the general requirements of the OPA.

Decision tree in case of an incident during the thermal shock
Anomaly observedProbable technical causeImmediate corrective actionSecuring measure
Bodily burn to a userUnexpected draw-off of 70 °C water at a point not locked offCooling with tempered running water and calling 144Closing the starting valve of the riser concerned
Sudden drop in temperature at draw-offInsufficient buffer volume or thermal back-up exceededInterrupting the flushing on the group of fittings in progressMaintaining heating until a stable return to 70 °C at the cylinder
Leak or pipe joint disconnection on the distribution networkExcessive thermal expansion on unguided synthetic pipeImmediate isolation of the section with a shut-off valvePartial draining to the nearest drain point
No hot water at the furthest pointPoorly balanced circulation loop or jammed regulating valveProlonged forced flushing with a contact thermometerContinuing the cycle for three minutes once stabilised

In the event of a skin burn, the absolute priority remains first aid: cool the affected area with tempered water from the cold water network for at least fifteen minutes and alert the medical emergency services if the injury exceeds the surface of the palm of a hand. As regards the installation, the team leader immediately locks off the section concerned, switches the production control back to standard mode and records the event in the construction site log. The company's liability is assessed on the rigour of the monitoring during the operation and on the material proof of the written notification given to the tenants or to the property management.

Frequently asked questions

How should you react if an occupant ignores the ban and scalds themselves during flushing?

Immediately cut the hot water at the start of the apartment riser concerned to neutralise the residual risk. Have first aid given by applying continuous cold water to the burn and call 144 if blisters appear. Note the exact time and the state of the notice on the landing door, and check that the written information receipt is present in order to establish the traceability of the prevention measures put in place.

What should you do if a thermostatic mixer blocks the passage of water at seventy degrees?

Apartment thermostatic cartridges incorporate a safety stop often set at 38 °C which prevents the passage of the thermal shock water. To disinfect the fitting, the handle must be removed or the cartridge temporarily bypassed according to the manufacturer's instructions. If access is impossible, the terminal must be removed and disinfected separately by chemical soaking, otherwise the decontamination of the draw-off point remains incomplete.

Why limit the duration of the thermal shock on networks made of synthetic materials?

Pipes made of cross-linked polyethylene or multilayer material undergo accelerated degradation of their molecular structure above 70 °C, while also undergoing strong linear thermal expansion. Prolonged holding at high temperature risks deforming the fixings, damaging the pressed joints and causing disconnections. As soon as the three minutes of flushing at 70 °C are reached at the tap, close the draw-off point to preserve the network.

What monitoring should be applied to inaccessible rooms or locked apartments?

A locked apartment represents a dead leg liable to re-seed the whole network after treatment. The installer must record in writing the impossibility of access on the flushing protocol given to the property management. The isolating valves in the landing duct supplying that dwelling must be closed during the thermal shock to prevent any unsupervised draw-off, then reopened only during a later scheduled visit for individual purging.

Texts and standards cited

  • OPAOrdinance on the Prevention of Accidents and Occupational Diseases: protective measures and installations taken by the employer in accordance with the rules of technology
  • Directive SSIGE W3Guidelines for drinking water installations: hygiene principles, temperature maintenance and control of Legionella proliferation in distribution networks

In the same section