Skip to content
Website
🧱 CFC 250Appliances, connections and built-in fittingsChapter 5 of 10 in the section

Connecting a washing machine: trap, loop height, stop valve and safety tray

This chapter details the installation rules for connecting a washing machine while avoiding major water damage. You will learn how to set the discharge height precisely to neutralise continuous siphoning, how to connect a vented trap that complies with sanitary rules, how to position a stop valve that can genuinely be operated, and how to secure installations on upper floors with a suitable collecting tray.

Key takeaways

  • A swan-neck pushed too far into the pipe causes the drum to empty continuously through suction.
  • The top of the drain hose loop must be between 60 and 90 centimetres above the finished floor.
  • The waste trap requires a permanent break in the head of water to preserve the water seal.
  • An easily operated isolating valve avoids keeping the hose under permanent static pressure.

Drainage: loop height, vented trap and prevention of self-siphoning

The classic mistake when connecting a washing machine is to push the flexible corrugated hose to the bottom of the drain standpipe. When the end of this hose dips below the water level in the machine's drum or reaches the water seal of the wall trap, draining creates continuous mechanical suction. The clean water admitted by the solenoid valve escapes straight to the sewer without the machine's pressure switch being able to stabilise the level. The cycle stays blocked, the heating element heats dry, or the machine shows a permanent fill fault.

Drum self-siphoning
Hydraulic phenomenon whereby the gravity flow of the drain creates a negative pressure in the pipe, sucking out the water held in the drum as soon as it fills if the upper air gap is not guaranteed.

To break this siphon effect, the drain pipe must incorporate an air break open to atmosphere. The sanitary installer fits an open drain sleeve or a recessed appliance trap with an air inlet. The flexible drain hose slides into it without a crimped watertight connection and is held by a rigid hose guide. The upper loop of the hose must sit above the maximum water level of the drum.

  1. Fitting the rigid drain pipeFix to the wall a drain pipe made of polyethylene or sound-insulated material, 50 or 56 millimetres in diameter, with a minimum fall of 1.5 per cent towards the stack.
  2. Positioning the trapInstall a removable exposed trap or a recessed box with an inspection hatch, ensuring a minimum water seal of 50 millimetres.
  3. Fitting the guide bendBend the corrugated hose over the plastic guide supplied and clamp it at the upper part to prevent any accidental slipping into the pipe.
  4. Checking ventilationCheck that there is a sufficient annular gap between the hose and the standpipe to allow free air to enter without foam being forced back.

Supply and retention: controlled stop valve and safety tray on upper floors

The drinking water supply to a laundry room or a private washing machine requires fittings designed to withstand the water hammer caused by the sudden closing of the solenoid valves. A straight or angle tap of three-quarters of an inch, incorporating a check valve and an integrated aerator, is always installed. This device prevents any return of polluted water into the building's cold water distribution network in accordance with the rules of the Swiss Society of the Gas and Water Industry.

The accessibility of this valve is essential for protecting the works. A valve hidden behind a heavy washing machine or built in behind a fixed piece of furniture remains permanently open. Under the continuous static pressure of the network, which commonly exceeds 4 bar in Swiss installations, flexible reinforced rubber hoses eventually burst through ageing or night-time overpressure.

Safety devices against damage from washing appliances
EquipmentMain functionConstruction site check point
Visible quarter-turn valveImmediate isolation by the userHeight between 100 and 120 cm, handle free of any obstruction
Mechanical water stop safety deviceAutomatic shut-off in the event of hose ruptureScrewed directly onto the tap outlet without an intermediate elbow
Watertight retention trayCollection of seepage and drum leaksPositioned under the machine and connected to the drainage system

When the appliance is installed on an upper floor or on a screed without overall floor waterproofing, a synthetic retention tray is essential. This tray, about ten centimetres deep, must be able to hold the entire capacity of a machine during a cycle, i.e. 50 to 70 litres, or be connected to a secure free drain. The sanitary installer ensures proper coordination on the construction site in accordance with art. 364 CO, which makes the contractor liable for the careful execution of the work in order to protect the floors below from destructive water damage.

Hydraulic commissioning: drainage dynamics and supply integrity

Commissioning a washing machine is not limited to connecting two hoses and screwing on a sealing ring. The peak discharge of a domestic drain pump commonly reaches twenty to thirty litres per minute. When the discharge hose is inserted into the drain pipe, the cross-section and the air balance must absorb this volume without causing splashing at the head of the stack or backflow through the water seal. A trap installed with a counter-slope or with an insufficient water seal destabilises the drainage: the pneumatic shock wave created by the ejected water plug drives out the residual seal of the adjacent appliance, letting drain odours rise.

On the supply side, the dedicated stop valve must be operable without tools and without contortion. A globe or ball valve hidden behind laundry-room furniture or placed under the worktop at arm's length breaches the operating rules: in the event of failure of the appliance's internal solenoid valve or rupture of the flexible hose, the user must be able to cut off the water supply instantly. Reinforced connecting hoses are subject to severe mechanical fatigue stresses due to the water hammer caused by the abrupt closing of the solenoid valves. The sanitary installer makes sure to fit, if the configuration of the distribution riser requires it, a diaphragm water hammer arrester approved by the SSIGE upstream of the draw-off point.

  1. Checking the water seal and air balanceFill the drain trap manually before connecting the appliance. Run a short rinse cycle to trigger forced draining at maximum flow, then visually check that there is no emulsion or overflow through the upper opening of the vented trap.
  2. Checking watertightness at working pressureOpen the stop valve fully and check the three-quarter-inch connection fitted with its new flat elastomer seal. Leave under continuous pressure for fifteen minutes without starting the machine to check the integrity of the hose crimps and the valve body.
  3. Validating the mechanical flow interruptionClose the isolating valve while water is being drawn off to confirm a clean cut-off of the flow, the absence of seepage at the gland and the free accessibility of the operating handle for the end user.

Connecting the retention tray, gravity drainage and sound insulation

Installing a washing machine on an upper floor requires a protective measure against water damage in the form of a prefabricated retention tray. This tray collects pump seepage, detergent drawer overflows or drum seal failures. The sanitary installer must connect the drain of this tray without creating a rigid link that would transmit vibrations. Drainage must be by gravity to a stack or a floor drain, necessarily provided with a permanent water seal or a dry anti-odour valve, since the tray is not supplied with water daily to replenish a conventional trap.

Analysis of washing machine connection faults and sanitary corrective actions
Fault observedDirect consequence for the workInstaller's corrective measure
Watertight fitting of the hose into the drainSelf-siphoning of the drum during fillingFit a sleeve with a break vent or leave a standard annular air gap
Stop valve located behind the machine drumImpossible to cut off the water in an emergency during a leakRelocate the valve to a visible surface-mounted position between 80 and 100 cm above the finished floor
Retention tray connected without mechanical decouplingTransmission of spin noise to the concrete structureInsert a flexible anti-vibration sleeve and place the tray on a sound-insulation strip
Safety tray trap without anti-drying systemEvaporation of the water seal and rise of foul airInstall a dry silicone membrane cartridge or connect to a combined trap with float

The transmission of structure-borne noise is subject to strict requirements in Swiss buildings under standard SIA 181. During spin phases exceeding a thousand revolutions per minute, the vibrations generated by the drum propagate directly to rigid pipes if the drain hose is rigidly clamped to the fixing brackets of the stack. Clamps fixed to party walls must incorporate decoupling elastomer linings. Likewise, high-density plastic pipes intended for sound-insulated drainage must be decoupled from slab penetrations by insulating sleeves in order to comply with the operating noise limit values permitted for adjacent sensitive rooms.

Fault diagnosis and remedial work after hydraulic malfunction

On a refurbishment or new-build construction site, two major hydraulic faults affect washing machine connections: endless filling through dynamic siphoning and foam backflow during rapid draining. When a machine stops and displays a water level error code, the first reflex is to check the immersion of the discharge hose. A corrugated hose dipped too deep into the drain pipe creates a continuous liquid bridge with the water seal of the trap. As soon as the drum starts to fill, the differential pressure sucks the clean water straight into the drainage collectors without the heating element switching on.

  1. Identifying and eliminating self-siphoningPull the corrugated hose out of the standpipe. Shorten the hose end to ensure a maximum penetration of 10 to 15 cm below the finished level of the socket cone. Fit a perforated centring piece or a ventilation sleeve that provides a permanent free air intake between the hose and the polyethylene pipe, thereby neutralising any negative pressure downstream.
  2. Checking drainage flow and backflowIn the event of soapy foam overflowing from the top of the wall trap, check the slope of the discharge pipe down to the stack and remove the inspection cup of the trap. Clogging by textile fibre deposits or the use of a badly oriented eccentric reducer forms an obstruction that slows the peak gravity flow.
  3. Eliminating supply leaks and securing the installationIsolate the supply at the angle stop valve. Replace the flat elastomer seals crushed by overtightening at the three-quarter-inch swivel connector. Check that the aquastop safety device is correctly positioned and reset the pneumatic or electromechanical valve integrated in the hose head.

When the appliance is installed on an intermediate floor or in an upper-floor laundry room without a watertight tanking, the failure of a solenoid valve under permanent static pressure can flood the slab within a few hours. In the event of a confirmed leak, the retention tray must channel the water to the floor drain without overflowing onto the perimeter skirting boards. The sanitary installer then replaces the standard valve with a valve with a check valve and a vent, while giving the client the instruction to isolate the supply between two cycles in accordance with the SSIGE guidelines and the rules of the trade.

Frequently asked questions

Why does the machine empty by itself during filling?

The drain hose is inserted too deep into the discharge pipe or the trap is placed below the level of the drum. The drain pump does not intervene: the clean water flows out by gravity and direct draw into the pipe. To eliminate this continuous siphoning, reposition the hose loop at least 60 cm above the floor and provide a free air intake at the top of the pipe.

How can soapy foam overflowing at the wall trap be avoided?

Modern drain pumps expel waste water at high speed with a large detergent emulsion. To prevent backflow, install a vertical pipe of 50 mm diameter to a minimum height of 30 cm above the water seal of the trap. Make sure that the appliance trap is fitted with an air inlet or vent to break the hydraulic plug effect during discharge.

Is the retention tray under the washing machine essential in an apartment?

On an upper floor, the absence of a watertight screed with a floor drain turns any supply failure into serious damage for the levels below. The safety tray in synthetic material or stainless steel is mandatory if the room does not have a waterproofed floor drain. It must be connected by gravity to the drainage network or combined with an electronic detection system that cuts the water at the main valve.

Must the stop valve always be closed after each wash?

The braided rubber supply hose remains under permanent pressure of several bar when it stays connected to the pipe. Under the effect of water hammer and ageing of the reinforcement, hose rupture is the leading cause of domestic flooding. Manually closing the quarter-turn valve, or installing a safety solenoid valve linked to the wash cycle, remains the official recommendation for protecting the sanitary installation.

Texts and standards cited

  • Directives SSIGEGuidelines for the execution of drinking water installations and the protection of internal networks against backflow and water damage.
  • norme SIA 118General conditions for the execution of construction work and rules governing the obligations and responsibilities of the contractor.

In the same section